Aqua Control EVOLUTION Manual de usuario

1Aqua Control, Inc. 60 Hz. Evolution Series Owner’s Manual

60 Hz. EVOLUTION INSTRUCTION MANUAL

Aqua Control, Inc.

6A Wolfer Industrial Drive

Spring Valley, IL 61362 USA

P: 1-800-377-0019

F: 815-664-4901

www.aquacontrol.com

Unit Serial Number:

___________________________________________

Light Set Serial Number:

___________________________________________

Distributor:

___________________________________________

Install Date:

___________________________________________

UNIT IDENTIFICATION

2 Aqua Control, Inc. 60 Hz. Evolution Series Owner’s Manual

SAFETY INSTRUCTIONS

IMPORTANT: Reading and understanding these instructions and warranty disclaimer

are necessary prior to product installation and operation.

• Under NO circumstances should anyone enter the water with the electrical equipment plugged in.

• NEVER run the unit out of the water. It may damage the motor seals.

• NEVER lift or drag the fountain by the power or light cord.

• Suitable for FRESHWATER applications only.

• The fountain suction screen should be inspected for clogging on a monthly basis. If matted weeds,

leaves or plastic bags are present, remove them with a bristle brush. Failure to keep the suction

screen clear of blockages will cause low water ﬂow and may cause premature motor failure. This

type of failure is NOT covered under the Aqua Control, Inc. Manufacturer’s Warranty.

• In freezing conditions, the fountain must be removed from the water body and stored in an area

above 32°F.

• Aqua Control, Inc. or its distributors are not liable for electrician’s fees incurred for troubleshooting

electrical issues.

TABLE OF CONTENTS

Assembling Your Floating Evolution 3

Control Box Installation 4

• Timer Programming

• StartUp

Accessory Installation 5

• Nozzle Installation

• Converting to a Torrent Pattern

• Light Set Installation

Evolution Parts List 6

Light Kit (optional) Parts List 7

Stationary Evolution Parts List 8

Troubleshooting Guide 9

Warranty Disclaimer 10

Parts Included

• 1/2HP Fountain (with Tornado and Torrent Spray Pattern capabilities) (1)

• Motor Cord or Quick Disconnect (1)

• Control Box (1)

• Mooring Rope (100’)

• Mooring Stakes (2)

Optional Accessories

• Lighting Kits

• Nozzle Kits

3Aqua Control, Inc. 60 Hz. Evolution Series Owner’s Manual

ASSEMBLING YOUR FLOATING EVOLUTION

Step #1

Place motor cord and fountain

pump thru the center of ﬂoat.

Align notch on fountain pump

with slot in ﬂoat.

Float should be positioned print

side up.

Step #5

Continue to ‘Control Box

Installation’ to complete startup

and installation.

Step #4

Place fountain in pond and

pull to desired location in

pond. Drive in mooring

stakes. (Note: Keep motor

and lighting cord plugs dry)

Step #3

Tie mooring (rope) lines to

mooring stakes.

If an optional nozzle or light

set were purchased see page

5 before putting unit in the

water.

Step #2

Measure and cut the

mooring rope into two

lengths. Tie to tabs on ﬂoat.

Motor Cord

Mooring Lines

Motor Cord

Quick Disconnect

Mooring Stake

4 Aqua Control, Inc. 60 Hz. Evolution Series Owner’s Manual

CONTROL BOX INSTALLATION

Step #1

Plug fountain motor cord

& light set cord (optional)

into the control box.

Receptacles in the control

box are labeled ‘LIGHTS’

& ‘FOUNTAIN’. Do not

reverse the plugs. The

photo cell controls the

light receptacle.

Step #2

Set ON/OFF times using

tripper pins. Insert ON

(Green) and OFF (Red)

trippers into dial at desired

times. Turn dial clockwise

and align arrow with Time-

of-Day (AM or PM) in

window.

Step #3

Plug control box cord into

standard 115V household

outlet.

Step #4

Turn on control and test

GFCI (Push ‘TEST’ button

and then Push ‘RESET’).

NOTE: Install control box in an area with natural light. Placing the control box in a

shaded area or an area that is lit at night will not allow the photo cell to properly

operate an otional light set.

Light Set Cord

Fountain Motor Cord

Control Box Cord

GFCI Reset

Timer with Pins

Photo Cell

GREEN

OFF

RED

5Aqua Control, Inc. 60 Hz. Evolution Series Owner’s Manual

OPTIONAL NOZZLE INSTALLATION

OPTIONAL LIGHT SET INSTALLATION

Step #1

Disconnect the unit from power.

Step #2

Insert Flow Straightener in throat

with reinforcing ring at top.

Step #3

Place nozzle onto throat, aligning

screw holes in nozzle ﬂange with

those in throat.

Step #4

Insert (4) screws through nozzle

ﬂange, into throat & tighten.

Nozzle

Reinforcing Ring

Throat

Flow Straightener

Nozzle Flange

Pan Head Screws

Upper Bracket Slots

Step #1

Place bracket in upper bracket slot,

rotate bracket down and snap into

lower bracket slot (bottom of ﬂoat).

Light ﬁxture not shown.

Step #2

Plug light set cord into control box.

Place

Rotate

Snap

CONVERTING TO A TORRENT PATTERN

Step #1

Disconnect the unit

from power.

Step #2

Remove prop washer,

prop bolt & lock washer.

Step #3

Reinstall prop bolt & lock

washer without prop

washer & tighten.

Prop Bolt

Lock Washer

Prop Washer

6 Aqua Control, Inc. 60 Hz. Evolution Series Owner’s Manual

EVOLUTION PARTS LIST

ITEM PART DESCRIPTION QTY.

OPTIONAL NOZZLE KITS

1N EVN-0.5-ARU 1/2HP ARUM NOZZLE KIT -

EVN-0.5-CLA 1/2HP CLUSTER ARCH NOZZLE KIT -

EVN-0.5-FLE 1/2HP FLEUR DE LIS NOZZLE KIT -

EVN-0.5-MET 1/2HP METRO NOZZLE KIT -

EVN-0.5-SAR 1/2HP SPIDER & ARCH NOZZLE KIT -

EVN-0.5-TIA 1/2HP TIARA NOZZLE KIT -

EVN-0.5-G2 1/2HP GUSHER 2 NOZZLE KIT (STATIONARY ONLY) -

EVN-0.5-G4 1/2HP GUSHER 4 NOZZLE KIT (STATIONARY ONLY) -

EVN-0.5-G6 1/2HP GUSHER 6 NOZZLE KIT (STATIONARY ONLY) -

2N EVN-FS EVOLUTION FLOW STRAIGHTENER INCLUDED (1)

3N 80-BHL-0.25X0.75 1/4-15X3/4 PANHEAD HI-LO SCREW INCLUDED (4)

FOUNTAIN PARTS

1H 80NH-0.31-24 5/16-24 HEX NUT 4

2H 80WL-0.31 5/16” LOCK WASHER 4

3H 80WF-0.31 5/16” FLAT WASHER 4

1U EVU-THROAT EVOLUTION THROAT 1

4H 80BH-0.25-2.25 1/4-20X2.25 HEX HEAD 1

5H 80WL-0.25 1/4” LOCK WASHER 1

2U EV-H-FW-PROP PROPELLER WASHER 1

3U EVU-PROP-1 1/2HP EVOLUTION PROPELLER 1

4U EVU-SPACER EVOLUTION MOTOR SPACER (FRANKLIN MOTOR ONLY) 1

MOTOR & CORD OPTIONS

M EVU6-M-0.50-00 1/2HP MOTOR OPTION (1)

MC EVU6-M-0.50-02 1/2HP MOTOR WITH QUICK DISCONNECT (MOTOR CORD SOLD SEPERATELY) OPTION (1)

MC EVU6-M-0.50-050 1/2HP MOTOR WITH 50’ OF CORD & MOLDED PLUG OPTION (1)

MC EVU6-M-0.50-100 1/2HP MOTOR WITH 100’ OF CORD & MOLDED PLUG OPTION (1)

MC EVU6-M-0.50-175 1/2HP MOTOR WITH 175’ OF CORD & MOLDED PLUG OPTION (1)

C EVU6-MCD-(LENGTH) EVOLUTION MOTOR CORD WITH QUICK DISCONNECT & MOLDED PLUG

(SOLD IN 25’ INCREMENTS)

OPTION (1)

C EVU6-A-MC-050-F 50’ MOTOR CORD ASSY & MOLDED PLUG OPTION (1)

C EVU6-A-MC-100-F 100’ MOTOR CORD ASSY & MOLDED PLUG OPTION (1)

C EVU6-A-MC-175-F 175’ MOTOR CORD ASSY & MOLDED PLUG OPTION (1)

5U EVU-SCREEN EVOLUTION SUCTION SCREEN 1

6H 80BHL-0.25X0.75 1/4-15X3/4 PANHEAD HI-LO SCREW 2

6U EVU-FLOAT EVOLUTION FLOAT 1

7U EVU6-CB EVOLUTION SERIES CONTROL BOX 1

8U EVU-ANCHOR MOORING ANCHOR 2

9U EVU-ROPE 100’ #6 BLACK MOORING ROPE 1

7Aqua Control, Inc. 60 Hz. Evolution Series Owner’s Manual

OPTIONAL LIGHT KIT PARTS LIST

ITEM PART DESCRIPTION QTY.

OPTIONAL LIGHT KITS

- EVL6-L3-000 3W 4 LIGHT 120V WITH QUICK DISCONNECT* -

- EVL6-L3-050 3W 4 LIGHT 120V WITH 50’ LIGHTING CORD* -

- EVL6-L3-100 3W 4 LIGHT 120V WITH 100’ LIGHTING CORD* -

- EV6L-L3-175 3W 4 LIGHT 120V WITH 175’ LIGHTING CORD* -

- EVL6-L9-000 9W 4 LIGHT 120V WITH QUICK DISCONNECT* -

- EVL6-L9-050 9W 4 LIGHT 120V WITH 50’ LIGHTING CORD* -

- EVL6-L9-100 9W 4 LIGHT 120V WITH 100’ LIGHTING CORD* -

- EVL6-L9-175 9W 4 LIGHT 120V WITH 175’ LIGHTING CORD* -

- EVL6-L9RGB-000 9W RGB 4 LIGHT 120V WITH QUICK DISCONNECT* -

- EVL6-L9RGB-050 9W RGB 4 LIGHT 120V WITH 50’ LIGHTING CORD* -

- EVL6-L9RGB-100 9W RGB 4 LIGHT 120V WITH 100’ LIGHTING CORD* -

-EVL6-L9RGB-175 9W RGB 4 LIGHT 120V WITH 175’ LIGHTING CORD* -

LIGHTING CORD OPTIONS

LC EVL6-LCD-(LENGTH) EVOLUTION LIGHT CORD WITH QUICK DISCONNECT & MOLDED PLUG (SOLD

IN 25’ INCREMENTS)

OPTION (1)

LC EVL6-LCS-050 50’ LIGHT CORD ASSY & MOLDED PLUG OPTION (1)

LC EVL6-LCS-100 100’ LIGHT CORD ASSY & MOLDED PLUG OPTION (1)

LC EVL6-LCS-175 175’ LIGHT CORD ASSY & MOLDED PLUG OPTION (1)

LIGHT KIT PARTS

1L EVL-3WF 3W EVOLUTION LIGHT REPAIR ASSEMBLY (BULB NOT INCLUDED) OPTION (1)

2L EVL-9W-SPL 9W LIGHT REPAIR ASSEMBLY - SPECIFY COLOR (INCLUDES 16/3 SPLICE KIT) OPTION (1)

3L EVL-9WF-RGB 9W RGB LIGHT REPAIR ASSEMBLY (INCLUDES 16/3 SPLICE KIT) OPTION (1)

4L EVL-BKT-1 EVOLUTION LIGHT BRACKET (FOR 3W & 9W, FLOATING UNITS) 4

5L 80WF-05 5MM FLAT WASHER 8

6L 80WL-05 5MM LOCK WASHER 8

7L 80NC-05 5MM ACORN NUT 8

3W EVOLUTION LIGHT FIXTURE PARTS

1F EV-H-MSF-4X16 4MM X 16 FLAT HEAD MACHINE SCREW 3

2F EVL-LENS 3W EVOLUTION CLEAR LENS 1

3F EVL-GSKT 3W EVOLUTION LIGHT GASKET 1

4F EVL-3WF-(COLOR) 3W LED BULB (SPECIFY COLOR) 1

EVOLUTION JUNCTION BOX

NOT SOLD SEPERATELY

1L 2L 3L

4F 1L

*Note: Replace ‘EVL6’ in all ﬂoating light set part numbers with ‘EVLS6’ if ordering lights for a Stationary

Evolution Series. See page 8 to view stationary light set brackets (included with stationary light sets) and

attachment information.

8 Aqua Control, Inc. 60 Hz. Evolution Series Owner’s Manual

STATIONARY EVOLUTION PARTS LIST

ITEM PART DESCRIPTION QTY.

STATIONARY STAND PARTS & HARDWARE

1S EVUS-FOOT STATIONARY EVOLUTION STAND FOOT 4

2S EVUS-LEG STATIONARY EVOLUTION STAND LEG 4

3S EVUS-RING STATIONARY EVOLUTION STAND RING 1

1H 80BH-0.25X0.63 1/4-20 X 5/8 HEX HEAD BOLT 24

2H 80NH-0.25-20 1/4-20 HEX NUT 24

3H 80WF-0.25 1/4” FLAT WASHER 24

4H 80WL-0.25 1/4” LOCK WASHER 24

4SL EVL-BKT-2 STATIONARY EVOLUTION STAND LIGHT BRACKET 4

1S 2S

4SL

3H 2H

STAND LEGS ASSEMBLED FOR

MAXIMUM WATER DEPTH

STAND LEGS ASSEMBLED FOR

MINIMUM WATER DEPTH

11.18.2016CS 9

Aqua Control, Inc. 60 Hz. Evolution Series Owner’s Manual

TROUBLE CHECK POSSIBLE SOLUTIONS

Fountain does not operate

-OR-

Starts then stops

Not plugged in

Cord must be plugged into a 3-wire outlet

that is protected by a GFCI or the suplied

Evolution Control Box.

GFCI Tripped

Reset GFCI. If GFCI will not reset or trips

immediately, unplug the pump & lights

and reset GFCI. If GFCI will still not

reset, there may be a problem with the

Evolution Control Box or the incoming

power. If the GFCI resets, plug the pump

in the Evolution Control Box. If the GFCI

trips, there may be a problem with the

pump cord. If the GFCI holds, plug in

the optional light kit. If the GFCI trips,

there may be a problem with the lights.

Contact Aqua Control Technical Support

to troubleshoot lights or pump

GFCI not tripped,

not running.

Disconnect power. Check propeller for

obstruction. These motors have internal

overloads. If the propeller is jammed,

the internal overload may trip. This

overload may require up to 10 minutes

to cool down & reset. If the motor

does not restart, there may be other

motor problems. Contact Aqua Control

Technical Support to troubleshoot the

pump.

Fountain spray pattern is not

reaching full size

Fountain intake clogged Disconnect power. Check suction screen

for obstruction & remove debris.

Nozzle clogged Disconnect power. Remove nozzle &

check for obstruction & remove debris.

EVOLUTION SERIES FOUNTAIN

TROUBLESHOOTING GUIDE

Aqua Control Technical Support

Available Monday thru Friday, 7:30AM - 5:00PM CST

Phone: 1-800-377-0019 or 1-815-664-4900

Email: [email protected]

-OR-

Contact Your Local Aqua Control Distributor

Tabla de contenidos

Otros manuales de Fuente al aire libre de Aqua Control

Aqua Control

Aqua Control FUSION Series Manual de usuario

Aqua Control

Aqua Control AQUATIC 1HP FUSION Series Manual de usuario

Manuales populares de Fuente al aire libre de otras marcas

Sunnydaze Decor

Sunnydaze Decor XSS-578 Manual de usuario

Campania International

Campania International Bibendum FT-400 Manual de usuario

Elkay

Elkay FLEXI-GUARD EFHA8 1M Series Manual de instalación

S.R.Smith

S.R.Smith Color Light Stream 2CLSLBK Manual de usuario

Hozelock Cyprio

Hozelock Cyprio Cascade 1500 Manual de usuario

Campania International

Campania International Juliet Fountain Manual de usuario

YARDART

YARDART FT-155 Manual de usuario

Alpine

Alpine WIN732 Manual de usuario

Campania

Campania Valencia Manual de usuario

Campania International

Campania International FT-320 Manual de usuario

GardenWize

GardenWize SWGSL230 Manual de usuario

Kelkay

Kelkay Easy Fountain Rustic Windmill Manual de usuario

Alpine

Alpine WIN258 Manual de usuario

Bond

Bond Signature Series Manual de usuario

Kenroy Home

Kenroy Home 51112COPBL Guía de instalación

EasyPro

EasyPro Tranquil Décor HBB39 Manual de usuario

Angelo Decor

Angelo Decor Castillo Manual de usuario

Campania International

Campania International Girona FT-102A Manual de usuario