Aoyue INT 2703A+ Manual de usuario

AOYUE®

INSTRUCTION MANUAL

Thank you for purchasing Aoyue Int2703A+ Repairing System.

It is important to read the manual before using the equipment.

Please keep manual in accessible place for future reference.

INT2703A+

Advanced Lead-Free

Repairing System

TABLE OF CONTENTS

Product Description ……………………………………………… 3

Specifications ……………………………………………………... 4

Package Inclusion ……………………………………………..… 5

Functions and Features ………………………………….…… 6

Safety Precautions …………………………………………….… 7

Assembly and Preparation ……………………………….…… 8

Control Panel Guide …………………………………..………… 9

Operating Guidelines ………………………………..….. 10—17

Auto-Sleep Functions …………………………………… 18—20

Digital Calibration ………………………………………… 21—23

Care and Maintenance …………………………………… 24— 26

Basic Troubleshooting Guide ……………………… 27— 29

Replacement Tips ……………………………………………… 30

Air Nozzles ………………………………………………………… 31

This manual is designed to familiarize and instruct the op-

erator with the proper usage and maintenance of the

equipment. The “Care and Safety Precautions” section

explains the hazards of using any type of soldering or re-

working device. Please read carefully and observe the

guidelines in order to maximize usage and minimize the

risk of injury or accidents .

The Aoyue INT2703A+ Advanced Lead-Free Repairing System is a

reworking equipment that combines the functionality of Hot Air Gun,

Soldering Iron, Smoke Absorber, and Desoldering Gun in one package.

The dual port system of the Int2703A+ allows simultaneous use of

the desoldering gun and soldering iron.

The nozzle is specially designed with air spreader technology to

disperse heat and air evenly greatly enhancing the heat output for more

effective reflows. When paired with our fourth generation BGA nozzle

technology, reworking larger BGAs (CPUs GPUs) will be even more

efficient and repeatable.

It has several safety features such as the auto-cooling process of

the Hot Air Gun. This functionality protects the device (and its

components) from excessive heat upon reaching any of the following

conditions: (1) when the soldering gun remained idle on its resting

handle after a certain period and (2) when the temperature of the

device is above a safe threshold upon turning off.

It has several advanced features such as solder iron and

desoldering gun digital calibration, configurable auto sleep for the hot-

air gun, soldering iron and desoldering gun.

There is an automated function that allow the programming of a 5

segment reworking profile for automated and consistent reflows.

Finally, the unique, innovative design with digital control panel and

display provides precision, safety, and ease of use to match all

reworking requirements.

PRODUCT DESCRIPTION

MAIN STATION

Power Input : available in 110V / 220V

Station Dimensions: 188(w) x 126(h) x 250(d) mm

Weight: 5.6Kg

SOLDERING IRON

Power Consumption: 70W

Temperature Range: 200°C - 480°C

Heating Element: Ceramic Heater

Output Voltage: 24V

HOT AIR GUN

Power Consumption: 500W

Temperature Range: 100°C - 480°C

Heating Element Metal Heating Core

Pump/Motor Type: Diaphragm Pump

Air Capacity: 23 l /min (max)

DESOLDERING GUN

Temperature Range: 200°C - 480°C

Heating Element: Ceramic Heater

Output Voltage: 24V

SPECIFICATION

Specifications are subject to change without prior notice.

PACCKAGE INCLUSIONS

* Type of soldering tip included might change depending on availability.

** Kindly refer to soldering iron stand installation insert for parts and

instructions.

1 unit Int2703A+ Main Station with Hot Air Gun and holder.

1 pc. 20094 Spare Heating Element (Hot Air Gun)

1 pc. 1130 Air Nozzle (Single ø4.4mm)

1 pc. 1197 Air Nozzle (Single ø9 mm)

1 pc. 3232W Multi-Chambered Air Nozzle (BGA 31 x 31 mm)

1 pc. 30202X Plastic Mesh Cover

1 pc. 30201X Suction/Vacuum Cover

2 pcs. 30181X Black Filter Pads

1 pc. B012 Soldering Iron with Smoke Absorbing function

1 pc. WQ-2B Soldering Tip*

1 pc. 30150J Heat Resistant Pad

1 pc. 2663B Soldering Iron Stand**

1 pc. B1003A Desoldering Gun with 301212 tip (1.8mm)

1 pc. 201413 Desoldering Gun Holder

1 pc. 302082 Desoldering Tip (1.0mm)

1 pc. 302092 Desoldering Tip (1.5mm)

1 pack 3017J Filter Pads (6pcs.)

1 pc. 201252 Spring Filter

1 pc. 3024X Spring Filter Cap

1 pc. 201242 Cleaning Pin

1 pc. 20178 Cleaning Drill

1 pc. H022 Cleaning Gel

1 pc. G001 IC Popper

1 pc. 939 Vacuum Pen

1 pc. Power Cord

1 pc. Instruction Manual

FUNCTION and FEATURES

●Microprocessor-controlled ESD safe equipment.

●4-in-1 repairing system combining Hot Air Gun, Soldering Iron,

Smoke Absorber and Desoldering Gun in one sophisticated

package.

●Advance technology air spreader nozzle

●Digital control and display of hot air temperature, soldering iron

temperature, desoldering gun temperature and air pressure with

touch type panel controls for precision and ease of use.

●The desoldering gun is equipped with air cylinder type vacuum

pump for stronger suction and zero-crossing circuit that

prevents electrical surges.

●Integrated smoke absorber functionality with filter pad to

efficiently absorb and filter harmful fumes.

●Automated reflow function with 5 segment programmable

profile.

●Uniquely designed compound tip that integrates the ceramic

heating element and sensor in just one component. Replacing

tips is as easy as slipping it in/out of the compatible 24V

soldering iron.

●User configurable 1 to 60 minute idle-to-auto-sleep mode for

additional device protection and power saving.

●Built-in auto-cooling process that protects the system and its

components from excessive heat, prolonging usage life.

●Large selection of air nozzles.

●Compatibility with different kind of soldering tips.

SAFETY PRECAUTIONS

CAUTION: Improper usage can cause serious injury topersonnel

and/or damage to equipment. For your own safety, please observe

the ff. precautions.

●Check each component after opening the package to make sure

everything is in good condition. If there are any suspected damage,

do not use the item and report the issue to your vendor.

●Turn OFF the main power switch and unplug the device when

moving the device from one location to another.

●Do not strike or subject the main unit to physical shock. Use

carefully to avoid injury and damage to any part.

●Handle with care.

- Never drop or sharply jolt the unit.

- Contains delicate parts that may break if the unit is dropped.

●Make sure the equipment is always grounded. Always connect

power to a grounded receptacle.

●Temperature may reach as high as 480°C when switched ON.

- Do not use the device near flammable gases, paper and other

flammable materials.

- Do not touch heated parts, which can cause severe burns.

- Do not touch metallic parts near the tip.

●Disconnect the plug from the power source if the unit will not be

used for a long period.

- Turn off power during breaks, if possible.

●Use only genuine replacement parts.

- Turn off power and let the unit cool before replacing parts.

●The unit may produce a small amount of smoke and unusual odor

during initial usage. This is normal and should not yield any

negative result when reworking.

●Soldering process produces smoke — use on well ventilated place.

●Do not alter the unit, specifically the internal circuitry, in any

manner.

ASSEMBLY and PREPARATIONS

A. Main Station

As soon as the equipment has been removed from the package,

REMOVE THE SCREW located at the center of the bottom of the

main unit. This screw holds the pump in place during transportation.

B. Soldering Iron

1. See instructions on 2663B soldering iron holder assembly guide

on page 10.

2. Connect the soldering iron cord assembly to the soldering iron

output terminal found at the lower middle portion of the main

unit.

3. Place the soldering iron to the soldering iron stand.

C. Smoke Absorber

1. Attach the smoke absorbing tube to the suction vacuum cap.

Make sure the cord connections are free from tangles.

D. Hot Air Gun

The Hot Air Gun holder was installed on the station upside down for

packaging purpose. To set up the Hot Air Gun holder:

1. Loosen the two screws that secure the holder to the station.

2. Turn the holder right side up.

3. Re-fasten the two screws.

4. Place the hot air gun onto the holder in preparation for usage.

E.Desoldering Gun

1. Connect the cord of the desoldering gun to the desoldering gun

terminal .

2. Connect the vacuum tube to the suction vacuum cap.

3. Place the desoldering gun onto the holder in preparation for

usage.

WARNING: Failure to remove the screw before using the

equipmentcancausedamagetothesystem.

CONTROL PANEL GUIDE

LEGEND:

1 — Airflow Gauge

2 — Hot Air Gun Temperature Adjustment Buttons

3 — Hot Air Gun Airflow Adjustment Buttons

4 — Soldering Iron Temperature Control Buttons

5 — Desoldering Gun Temperature Control Buttons

6 — Hot Air Gun Output Terminal

7 — Smoke Absorber Terminal or Vacuum Cap

8 — Desoldering Gun Receptacle

9 — Soldering Iron Receptacle

10 — Main Power Switch

11 — Desoldering Gun Temperature Display

12 — Desoldering Gun Function Activation Switch

13 — Soldering Iron Temperature Display

14 — Soldering Iron Function Switch

15 — Smoke Absorber Function Switch

16 — Hot Air Gun Air flow Display / Automate Display

17 — Hot Air Gun Automate Function Selector

18 — Hot Air Gun Temperature Display /Automate Display

19 — Hot Air Gun Function Switch

6 7 8 9 10

AOYUE®

REPAIRING SYSTEM Int 2703A+

18 19

OPERATING GUIDELINES

IMPORTANT REMINDERS:

1. Make sure the equipment is placed on a flat stable surface

and all the heat-generating components placed on their

respective holders or stands.

2. Ensure all function switches are OFF prior to reworking.

3. Ensure all terminal connections are properly secured.

IMPORTANT: Pleasereferto the CONTROL PANEL GUIDE page

forbuttonsanddisplaypaneldirectory.

A. INITIAL PROCEDURES

1. Plug the device to the main power source using the power cord

provided in the package.

2. With all function switches deactivated and all terminal connections

properly secured, switch ON the device by activating the main

power switch (“10” from the control panel).

3. The display panels, will temporarily show the product name

“AOYUE Int 2702” and then display “OFF”. The system will remain

at this state until the user activates a function.

SOLDERING IRON

OPERATING GUIDELINES

ASSEMBLY and PREPARATIONS

Otros manuales para INT 2703A+

Tabla de contenidos

Otros manuales de Pistola de soldar de aoyue

aoyue

aoyue SP4000 Manual de usuario

aoyue

aoyue Tesla Series Manual de usuario

aoyue

aoyue Int701A++ Manual de usuario

aoyue

aoyue 8011 Manual de usuario

aoyue

aoyue INT 738 Manual de usuario

aoyue

aoyue SP2000+ Manual de usuario

aoyue

aoyue INT9378 Manual de usuario

aoyue

aoyue 937 Plus Manual de usuario

aoyue

aoyue 2900 Manual de usuario

aoyue

aoyue 888A Manual de usuario

aoyue

aoyue Int732 Manual de usuario

aoyue

aoyue Tesla Manual de usuario

aoyue

aoyue 469 Manual de usuario

aoyue

aoyue Int936A Manual de usuario

aoyue

aoyue SP2000 Manual de usuario

aoyue

aoyue INT 2702A+ Manual de usuario

aoyue

aoyue Int3210 Manual de usuario

aoyue

aoyue 469 Manual de usuario

aoyue

aoyue 853a+ Manual de usuario

aoyue

aoyue 2901 Manual de usuario

aoyue

aoyue Int2930 Manual de usuario

aoyue

aoyue INT 738H Manual de usuario

aoyue

aoyue 853 Manual de usuario

aoyue

aoyue 968A+ Manual de usuario

Manuales populares de Pistola de soldar de otras marcas

Bakon

Bakon 3200 Manual de usuario

Proxxon

Proxxon Gaslotset MGS Manual de usuario

jbc

jbc SFR-A Manual de usuario

jbc

jbc CL8010 Manual de usuario

HAKO

HAKO FX-8804 Manual de usuario

SATA

SATA 02002A Manual de usuario

Velleman

Velleman HRJA151 Manual de usuario

Weller

Weller WSM 1 Manual de usuario

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Instrucciones de montaje

ersa

ersa i-CON 1V Manual de usuario

Hakko Electronics

Hakko Electronics FX-100 Manual de usuario

Weller

Weller WAD 101 Manual de usuario

Weller

Weller WXD 2 Manual de usuario

AlienTek

AlienTek T100 Manual de usuario

Atten

Atten ATETOOL AT-689A Manual de usuario

Surtek

Surtek 112554 Dimensiones y guía de instalación

Parkside

Parkside PLBS 30 A1 Manual de usuario

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Manual de usuario

aoyue INT 2703A+ Manual de usuario

Manuales populares de Pistola de soldar de otras marcas