AOR AR-STV Manual de usuario
®
AR-STV
WIRELESS CAMERA DETECTOR
Operating manual
AOR, LTD.
TABLE OF CONTENTS
Introduction -------------------------------------------------------------------------------------- 2
1-1 Maintaining the unit --------------------------------------------------------------------------- 2
1-2 Power requirements -------------------------------------------------------------------------- 2
1-3 Supplied accessories ------------------------------------------------------------------------ 3
1-4 Features ----------------------------------------------------------------------------------------- 3
2 Control and functions------------------------------------------------------------------------- 3
2-1 Front panel controls--------------------------------------------------------------------------- 3
2-2 Rear Panel -------------------------------------------------------------------------------------- 6
3 Connections--------------------------------------------------------------------------------------- 7
4 Power Switch------------------------------------------------------------------------------------- 7
5 Operations of the AR-STV ------------------------------------------------------------------- 7
5-1 isplay ------------------------------------------------------------------------------------------- 7
5-2 Operation mode ------------------------------------------------------------------------------- 8
5-2-1 Search mode -------------------------------------------------------------------------------- 8
5-2-2 Memory mode ------------------------------------------------------------------------------- 11
5-2-3 Setting mode -------------------------------------------------------------------------------- 13
5-3 PC interface ------------------------------------------------------------------------------------ 15
6 Specifications------------------------------------------------------------------------------------ 6
7 Limited warranty (USA only)---------------------------------------------------------------- 7
FCC statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
1
Introduction
Thank you for purchasing the AR-STV Wireless Camera etector.
The AR-STV is a wireless camera receiver with a 2.5 inch color LC display, still picture recorder
and sensor that captures analog video signals in real-time. It is mainly designed for use in
surveillance applications.
Its built-in clock allows images to be time-stamped and a (non-supplied) S memory card can be
used to store images.
© This manual is protected by copyright AOR, LT . 2013. No information contained in this manual
may be copied or transferred by any means without the prior written consent of AOR, LT .
AOR and the AOR logo are trademarks of AOR, LT . All other trademarks and names are
acknowledged.
- Maintaining the unit
There are no internal operator adjustments. In the unlikely event of service being required, please
contact your dealer for technical assistance.
Level of risk:
As the AR-STV operates with a 6 V C power source, there is little chance of serious injury as long
as common sense is applied.
Observe the polarity of connections if using an external battery charger. C input is a nominal 6V
C, with the connector wired center conductor positive. Reverse polarity connection will damage the
AR-STV and could lead to the risk of fire or explosion under severe circumstances.
NEVER connect the AR-STV directly to the AC outlet.
Handling the AR-STV:
Use a soft, dry cloth to gently wipe the AR-STV clean. Never use abrasive cleaners or organic
solvents which may damage certain parts. Treat the unit with care, avoid spillage or leakage of
liquids into the cabinet and power supply. Special care should be taken to avoid liquid entering
around the keys, main dial or via the connectors.
[Note: Never push or knock the LC screen – it is very fragile and sensitive to shock.]
Special remarks:
o not use or leave the AR-STV in direct sunlight (especially the TFT display). It is best to avoid
locations where excessive heat, humidity, dust and vibration are expected. Always keep the AR-STV
free from dust and moisture.
-2 Power requirements
The AR-STV is designed for operation from a nominal 6 V C (4 AA size alkaline battery or Ni-MH
cells). The external 6V C power supply may be used to charge the internal Ni-MH cells.
Do not use an external power supply when alkaline battery cells are in the unit.
[ Notice: Always disconnect the external power supply when in use.]
2
-3 Supplied accessories
The following accessories are provided in the shipping box.
Instruction manual (this booklet)
Flexible rubber antenna
Belt clip
Soft case
Four AA size Ni-MH battery cells
C power supply / battery charger
-4 Features
Built-in 2.5 inch color LC display
Built-in clock for time stamp
Store images on a (non-supplied) S (or S HC) memory card
etect NTSC, PAL, CCIR, EIA or scrambled reverse polarity video signals
Receives and displays video signals on L-band (1.2 GHz) or S-band (2.4 GHz)
The USB connector makes it easy to download stored images into a computer
Easy to operate with four AA size batteries
Continuous search between 900 ~ 2800 MHz
10 search banks
Easy menu-driven operation
2 Controls and functions
2- Front panel
The front panel of the AR-STV is dominated by the large color LC . On the top right corner of the
AR-STV, there is a red LE marked as “STA” (Status). The LE blinks while in the search mode.
Front View
3
Left View Right View
Right Side of the AR-STV
Power ON/OFF switch
2 CONT (USB connector)
3 VIDEO (Video Output connector)
Slide the power switch upward to switch on the AR-STV.
To switch off the AR-STV, slide the switch downward.
Using a
USB A ←→ USB Mini (B)
cable (not supplied),
connect between the CONT (Control) connector and a
PC to download images
whi
ch have been previously
This 3.5 mm mono connector provides the
composite video output.
An external video monitor may be connected.
4
4 DC 6V (External power input connector)
5 SD (SD, SDHC memory card slot)
6 ALM OUT (Alarm output connector)
Pin assignment of the connector:
Tip --- Beep output and alarm output
Ring --Relay output (this pin will make a short circuit to the ground for 2 seconds after a video
signal is detected)
(Relay specifications: 50 V C, 150 mA max.)
Sleeve--- Ground
To charge the internal Ni-MH cells, connect the supplied C
power supply into this connector. Note that the center pin of
the jack is
positive.
Insert a (non-supplied) S memory card (up to 32 GB) into
this slot to save images.
Approx. 20,000 images may be saved on a 1GB S card.
Connect an external alarm device into this connector.
(Format: 3.5 mm stereo)
5
Left Side of the AR-STV
7 MODE (Mode selector) switch
8 REC (Record) switch
9 FREQ UP DOWN (Frequency selector switch)
2-2 Rear panel
Press this switch to select the operation mode.
Press this switch to store image onto memory.
Press this switch upward/downward to change the
receive frequency or change search direction.
With the supplied
belt clip attached.
Battery compartment
6
3 Connections
Connect the supplied flexible rubber antenna to the SMA antenna connector on the top of the AR-
STV.
If required, an external antenna may be connected with a SMA connector for the coaxial cable.
Insert the supplied 4 AA size Ni-MH cells into the
battery compartment in the AR-STV.
If the batteries are not yet charged, connect the
C power supply into the power input connector on
the right side.
4 Power switch
To switch on the AR-STV, slide the power switch on the right side of the AR-STV upward.
4- Start-up
After inserting the batteries, switch on the power switch. The LC displays search screen
and a STA (Status) LE will blink indicating the AR-STV is in the search mode.
4-2 Powering down
To switch off the AR-STV, slide down the power switch.
4-3 Low Battery
When internal battery voltage becomes low, the Low Battery indicator will appear on the LC
screen. In the meantime, a beep will sound.
When this message appears on the screen, all operations of the AR-
STV will quit automatically. Immediately switch off the AR-STV, and
replace all internal battery cells with new ones or charge the supplied
batteries by connecting the C powers supply. (Charging time approx.
10h)
5 Operations of the AR-STV
To set or remove the key lock, press the blue button and FREQ. OWN switch simultaneously.
5- Display
This section explains what you can expect to see on the AR-STV
LC monitor screen.
Once the AR-STV is properly powered up, this display will
appear on the screen:
7
( ) G 2G 3G (Hz)
The horizontal axis displays the receive frequency. The AR-STV can receive between 900 MHz and
2800 MHz.
(1G indicates 1 GHz in frequency, 2 G for 2 GHz, and 3 G for 3 GHz accordingly.)
(2) V (Video level) N (Noise level)
Video Level
The V (Video) line on the vertical axis displays the video quality threshold level.
Note that video level is NOT related to the signal strength.
Setting the video threshold level higher will display the video signal only with the better quality.
Setting the video threshold level lower will display the video signal even if it is of poor quality.
Noise Level
The N (Noise) line on the vertical axis displays the signal strength.
Setting the Noise threshold level higher can detect only strong signals.
Setting the Noise threshold level lower can detect any weak signals even of poor quality.
Video Level and Noise level can be adjusted on the Search Bank Setting Menu.
5-2 Operation Mode
There are three (3) operation modes with the AR-STV.
• Search Mode
• Memory Mode
• Setting Mode
5-2- Search Mode
This is a default operation mode of the AR-STV. On this mode, the AR-STV will search frequencies
between 900 MHz ~ 2.8 GHz (2800 MHz) continuously until signal is detected.
Once the AR-STV detects the signal, it will automatically
switch the screen to display the received video signal.
To stop searching, press the FREQ switch inward. Then
the screen on the right will appear.
8
Otros manuales para AR-STV
1
Tabla de contenidos
Otros manuales de Sensor de seguridad de AOR
