AnyTone Ares Manual de usuario

USER'S MANUAL

CONTENTS

FUNCTIONS & FEATURES..................................................................1

STANDARD ACCESSORIE..................................................................2

OPTIONAL ACCESSORIE ....................................................................2

INSTALLATION.....................................................................................2

GETTING ACQUAINTED......................................................................6

HOW TO USE YOUR RADIO ...............................................................8

SLIDE SWTICH.....................................................................................9

ERROE CODE ....................................................................................10

SPECIFICATIONS...............................................................................11

FUNCTIONS & FEATURES

FM/AM/PA mode

◆

Weather Channel 150-170MHz programmable(Optional)

◆

CTCSS/DCS Code(Optional)

◆

PWR, RX RSSI S-Meter

◆

PC programmable

◆

Echo Function

◆

SQ, ASQ Function

◆

RF Gain Adjustment

◆

Mike Gain Adjustment

◆

H/L power

◆

Programmable RB

◆

NB/ANL Function

◆

Offset Function

◆

Beep Voice Prompt

◆

+10KHz Function

◆

TOT Function

◆

HI-CUT Function

◆

Busy channel lock

◆

Monitor

◆

LED Brightness Adjustment

◆

SWR Protection

◆

Voltage Protection

◆

STANDARD ACCESSORIES

OPTIONAL ACCESSORIE

INSTALLLATON

Radio

Screws for

bracket

DC Power

Cable

USB Programming

Cable

External Speaker

Self-tapping

Screws

Microphone

Pads for

bracket

PadsAdjusting

screws

Microphone

Hanger

Mounting Bracket Non-slip

Mat

Spare Fuses

(10A,250V)

Choose the most appropriate setting from a simple and

practical point of view. Your radio should not interfere

with the driver or crash the driver's knee or leg when

rush brake.

Using the self-tapping screws and pads(2 sets) to x 1.

the bracket.

Put the Non-slip mat on the 2 ends of the bracket and put in the radio. Then insert2.

the adjusting screws and check careful each screws, make sure the screws and

machine will not loose when the car shaking.

Choose suitable angle by the 3 screw holes in the two ends of bracket.3.

Microphone connection

Plug microphone connector into jack.1.

Pull on the screw for microphone connector.2.

MIC

VOL

MIG

OFF

RFG

TONE

ARES

DATA

RX/TX

BAND

DIM

MON

RF PWR

NB/ANL

ANL

OFF

+1OK

OFF

BAND

PWR

+30dB

753

S G

MIC

VOL

MIG

OFF

RFG

TONE

ARES

DATA

RX/TX

BAND

DIM

MON

RF PWR

NB/ANL

ANL

OFF

+1OK

OFF

BAND

PWR

+30dB

753

S G

ANTENNA INSTALLATION

POWER CONNECTION

Before using this radio, please install a high efficent and harmonious adjusted

CB antenna, suitable antenna type and correct installation will bring excellent

communication.

To match with the radio, the antenna and cable shall with characteristic impedance of

50ohm, or the antenna system will not efcient enough and will disturb TV, radio or other

electronics.

Screw the antenna connector into the antenna jack.1.

Grounding the antenna system to ensure best performance of this radio.2.

This radio adopt 13.8V power supply, never connect it to 24V battery, And the 13.8V car

battery shall with sufcient current, or the LCD will become dark and Transmit power

will drop down.

The position of antenna can be put as following example:3.

WARNING:

▲ Connect antenna rstly before transmiting, or it might damage the radio.

▲ To avoid the risk of fire, electric shock, radio damage, all base station shall

equip of lightning protector

▲ Be sure choose a matching antenna, you may enquiry our dealers.

Connect positive red power cable with the + terminal of the battery.1.

Connect negative black power cable with the - terminal of the battery.2.

Connect the DC power cable to the transceiver's power supply connector.3.

▲ We suggest not use cigar lighter as it often bring down the voltage.

▲ Locate the power cable away from high temperature, moisture, portre and cable

insulator.

▲ Use a full power cable even it is longer than need, do not take off the fuse holder

from the cable.

Connected

to chassis

Replacing Fuse

This radio adopt 10A, 250V fuse.

If the fuse blows, determine the reason, then correct the problem.

After the problem is resolved, replace the fuse. If newly installed fuses continue to

blow, disconnect the power cable and contact your autho-rized dealer or an authorized

servicecenter:

Pull the two fuse cover in difference direction and open it.1.

IN-LINE

FUSE HOLDER

Replace the broke fuse with good one, and close the fuse holder.2.

Be sure to use suggested fuse, or it might damage the radio.3.

FUSE

IN-LINE

FUSE HOLDER

IN-LINE

FUSE HOLDER

IN-LINE

FUSE HOLDER

10A 250V FUSE

Install External Speaker

If use an external speaker, please choose 8ohm speaker with 3.50mm mono band

(doulbe cable) plug.

Locate the external speaker in a suitable place.1.

Plug into the speaker jack.2.

Install Microphone Hanger

Choose a ideal location which will not interfere

the driver. Using supplied self-tapping screws and

pads(2 sets) to x the hanger.

GETTING ACQUAINTED

Front Panel

No. Functions

1S-Meter

2 Control NB/ANL function on/off

3 Control power level

4 Control Monitor/10K on/off

5Control LED brightness

6 Choose H and L band group

7 TX/RX indicator

8 PC programming port

9 Channnel dispplay

10 Mike connector

11 Power on/off volume level control

12 Squelch level control

13 Control Mike gain level

14 Control RF gain level

15 Choose AM/FM/PA mode

16 Choose working band

17 Control echo rebound times

18 Control echo duration time

19 Channel Switch

MIC

VOL

MIG

OFF

RFG

TONE

ARES

DATA

RX/TX

BAND

DIM

MON

RF PWR

NB/ANL

ANL

OFF

+1OK

OFF

BAND

PWR

+30dB

753

S G

10 15 16 1912 1814

2 3 4 5 6 7 98

11 13 17

Microphone

Rear Panel

Channel Down Channel UP

Microphone cable

Mic

PTT

Connector

No. Functions

20 External SP Jack

21 External PA Jack

22 Antenna Jack

23 Power Supply Jack

22 21

ANT.

PA.SP. EXT.SP.

POWER

Squelch Control

RF Gain Control

Mic Gain Control

Working mode Control

Working Band Control

Echo times Control

Echo duration Control

When the radio is standby, turn SQ outter shaft clockwise to adjust squelch level.

When the radio is receiving, turn RFG outter shaft to adjust RF gain. Turn it clockwise

to increase gain, anti-clockwise to reduce gain.

When the radio is transmiting, turn MIG inner shaft to adjust RF gain. Turn it clockwise

to increase gain, anti-clockwise to reduce gain.

Turn the mode switch to choose AM/FM/PA mode.

Turn the band switch to choose A/B/C/D/E/F band.

When Echo function is on, turn Tone inner shaft to adjust echo rebound times. Turn

it clockwise to increase times, anti-clockwise to reduce times.

When Echo function is on, turn Tone outter shaft to adjust echo duration time. Turn it

clockwise to increase time, anti-clockwise to reduce time.

Channel Selection

Turn the channel knob to select desired channel.

Clockwise to increase, anti-clockwise to reduce channel.

HOW TO USE YOUR RADIO

OFF/ON Radio

Turn VOL clockwise to switch on the radio, the radio emit a beep. When the LED1.

displays frequency or channel, the radio is on.

Turn VOL anti-clockwise to switch off the radio, the radio is OFF when hear Ka2.

Ta from the switch.

Volume Control

When the radio is turned on, turn VOL clockwise will increase the volume, turn VOL

anti-clockwise will reduce the volume.

Note: Adjust the volume during communication to get suitable level.

Tabla de contenidos

Otros manuales de Radio de AnyTone

AnyTone

AnyTone AT-D868UV Instrucciones de funcionamiento

AnyTone

AnyTone 578 Go Box DIY Kit Manual de usuario

AnyTone

AnyTone METIS Manual de usuario

AnyTone

AnyTone AT- 778UV Manual de usuario

AnyTone

AnyTone AT-5555 PLUS Manual de usuario

AnyTone

AnyTone 868 Manual de usuario

AnyTone

AnyTone ARES II Manual de usuario

AnyTone

AnyTone SMART II Manual de usuario

AnyTone

AnyTone GRACES Manual de usuario

AnyTone

AnyTone AT-318UV Manual de usuario

AnyTone

AnyTone MINI CB Manual de usuario

AnyTone

AnyTone AT-3318UV Manual de usuario

AnyTone

AnyTone AT-D578UV Guía de configuración

AnyTone

AnyTone AT888 Manual de usuario

AnyTone

AnyTone AT-588UV Manual de usuario

AnyTone

AnyTone SMART Manual de usuario

AnyTone

AnyTone Dual Band FM Transceiver Manual de usuario

AnyTone

AnyTone AT-398UV Manual de usuario

AnyTone

AnyTone AT-5189 Manual de usuario

AnyTone

AnyTone ARES II Manual de usuario

AnyTone

AnyTone AT-779UV Manual de usuario

AnyTone

AnyTone AT-300M Manual de usuario

AnyTone

AnyTone AT-588 Manual de usuario

AnyTone

AnyTone DORIS Manual de usuario

Manuales populares de Radio de otras marcas

EisSound

EisSound KBSound iSelect Manual de usuario

Midland

Midland 1001LWX Manual de usuario

Konig

Konig HAV-SR41 Manual de usuario

Roberts

Roberts exprssion Manual de usuario

VDigi

VDigi DD3.0 Manual de usuario

Radio Shack

Radio Shack 21-1863 Manual de usuario

Roberts

Roberts Stream 207 Manual de usuario

Sony

Sony Walkman SRF-M97 Manual de usuario

Stanley

Stanley FatMax FMC770 Manual de usuario

auna

auna DAB-Radio 10026947 Manual de usuario

SOUNDMASTER

SOUNDMASTER UR190 Manual de usuario

HYT

HYT TC-320 Manual de usuario

auna multimedia

auna multimedia Yellowstone 10026851 Manual de usuario

B-Tech

B-Tech GMRS-V2 Manual de usuario

Weierwei

Weierwei VEV-V8 Manual de usuario

SOUNDMASTER

SOUNDMASTER DAB750 Manual de usuario

Telefunken

Telefunken TF-1505 Manual de usuario

Makita

Makita LXRM03 Manual de usuario