ANYTHING3D XT-100 Manual de usuario
XT•350
&
XT•100
MOTORIZED TURNTABLES
MANUAL
The information in this manual is furnished for information use only, is subject to
change without notice, and not be construed as a commitment by Anything3D Corp.
Anything3D Corp assumes no responsibility or liability for any errors or inaccuracies
that may appear in this book.
© 000 001 Anything3D Corp. All right reserved.
CONTENS
1. Safety instructions ..................................................
. Introduction ............................................................ 6
3. Complete set of equipment .................................... 10
4. Description........................................................... 1
5. Installation ........................................................... 14
6. Operating controls ................................................ 16
7. Preparing for photography ..................................... 1
7.1 Connecting the Turntable .................................. 1
7. . Starting the Turntable ...................................... 7
8. Operating modes .................................................. 9
9. Rotation speed adjustment mode ........................... 33
10. Manual mode...................................................... 37
11. Slave mode......................................................... 40
1 . Optional auto mode ............................................. 43
13. Frequently asked questions ................................. 46
14. Recommendations for use ................................... 48
15. Troubleshooting ................................................ 53
16. Maintenance ...................................................... 55
17. Specification ...................................................... 57
18. Product warranty................................................. 59
NIKON is a registered trademark of Nikon Corporation.
Anything3D and Anything3D logo are registered trademarks of
Anything3D Corporation.
Photo3D and Photo3D logo are registered trademarks of Anything3D
Corporation.
MS Windo s is a registered trademark of Microsoft Corporation.
4
1. SAFETY INSTRUCTIONS
1. SAFETY INSTRUCTIONS
1. Please, carefully read these instructions.
. The turntable must be installed on a flat
horizontal surface, otherwise it won’t work
properly.
3. Use AC power source indicated in the
specification ONLY.
4. Turn on the equipment only via proper
ly earthed sockets.
5. Never use a damaged power cable.
6. When using an extension piece, make sure
that the total current value doesn’t exceed
the permissible one.
Figure 1.1
Figure 1.2
5
1. SAFETY INSTRUCTIONS
7. The total current consumed by all devices
through the common outlet should not ex
ceed its rated current.
8. Always turn off the turntable if the power
cable or socket is damaged, if liquid has
got inside the turntable or if the turntable
works improperly.
9. After switching the turntable off DO NOT
switch it on again before seconds have
elapsed.
10. Always switch off your turntable by using
the button on the power panel.
11. Never take the plug out of the socket
before the indicators on the control panel
go off.
1 . Before cleaning the table disconnect it
from the power source.
13. Never use volatile flammable liquids
to clean the turntable.
Figure 1.3
6
1. SAFETY INSTRUCTIONS
14. DO NOT perform maintenance and repair
of the turntable yourself. In case of any
trouble contact ANYTHING3D.
15. Make sure that during rotation the turnta
ble spinning surface doesn’t contact with
the external objects.
16. See to it that the load on the turntable is
as close to the center as possible or else it
might cause damage to the turntable.
(Fig. 1.4)
17. Never place the photographed objects on
the turntable while it is spinning.
CorrectIncorrect
Figure 1.4
to contents
7
1. SAFETY INSTRUCTIONS
8
2. INTRODUCTION
2. INTRODUCTION
ANYTHING3D XT100 AND XT350 MOTOR
IZED TURNTABLES are intended for automa
tion of 3D photography process. With 3D
photography the objects you are taking pic
tures of can be seen on the computer screen
and you can get the complete visual informa
tion about all their features! Our turntable lets
you get the 3D images series of any object
you choose. This widely adaptable kind of 3D
images is in great demand. They could be
used in Internetshops, on the model agen
cies sites, at the advertising shows, presen
tations, etc.
XT350 model 39" in diameter is intended
for making the photos of people and large
objects. XT350 turntable is capable of
bearing the heavy objects with a weight of
up to 350 lb.
XT100 model is 0" in diameter and bears
the objects with a weight of up to 100 lb.
XT350 and XT100 turntables have the
same indication, controls and functional abil
ities. In addition to the common function
abilities ХТ350 turntable is equipped with a
frame number sound indication, as well as
with a pullout handle and wheels to move the
turntable around your photo studio.
The turntable enables a series consisting of
different quantities of images (3 , 16 or 8
frames). You may take any number of frames
depending on your quality and technical re
quirements. A series of 3 frames produces a
9
2. INTRODUCTION
10
2. INTRODUCTION
highquality 3D photo with a bigger file size. A
series of 8 frames gives the smallest file size
and requires the least time to be loaded
through the Internet. A series of 16 frames is
a compromise between quality and file size.
ANYTHING3D XT100 AND XT350 MOTOR
IZED TURNTABLES render 3D photography
as simple as 1, ,3! You may take pictures in
manual, semiautomatic or automatic
modes. The enhanced indicating system
gives you complete control over the process
of photography. Due to its adjustment sys
tem the turntable is well adaptable to the var
ious photo studio equipment and cameras.
The best results will be attained by means of
using a modern digital camera and a set of
the studio lighting equipment as in this case
you make the best of all the turntable appli
ances for automatic photography in order to
compile a 3D series.
The original Anything3D software included in
the complete set offers a wide variety of 3D
series processing options and their further
usage.
Este manual sirve para los siguientes modelos
1
Otros manuales de Placa giratoria de ANYTHING3D
