Anytek T12+ Manual de usuario
1
◆Preface
Thank you for purchasing the Anytek T12+ Car Dash
Cam.
Please ensure that you have read the product manual
and instructions in full, prior to installation and use.
Failure to do so may result in product failure/damage or
incorrect operation and therefore impact the product
performance
◆Copyright infringement warning
Please note that this product is only for personal use, the
method of use shall not violate the goods infringe on
domestic or international copyright laws. Even recorded
images for personal use only, please note that in some
cases to use this product to record performances,
exhibitions or business activities of the image may
infringe the copyright or other legal rights and interests of
others.
◆NOTE
- Do not open or disassemble the product, which could
lead to electric shock or equipment damage. If necessary,
2
referred to the service center or professional treatment.
- The product can be used in other applications, such as
photography, self-timer and so on.
- Do not stack items on the device, do not press the
screen, may cause the screen breakage.
- Do not use sharp objects touching the screen, in order
to avoid damage to the screen.
- Do not let children play with the device.
- When the device is working, if the car charger pulled
out from the cigarette lighter, the device will shut down.
If the following situations arise , please contact the
service center:
- Charger cable is damaged or broken;
- Housing damaged, transformer damage or the internal
components exposed;
Please note that the charger itself consumes power, if the
device is not in use, pull out the charger to avoid the
battery discharged.
◆The working conditions
- Don't be exposed to high temperatures or direct
3
sunlight, especially in the car. Avoid the dust get into the
device.
- Avoid to use in damp environment . Please note that in
a closed environment, the moisture in the air easy to
condense and attached to the device.
- Avoid touch and intense impact.
-Keep the device and its accessories away from
flammable and explosive, corrosive liquid or gas.
- Cleaning the device, please put down from the scaffold
before it. Using a soft wet cloth clean screen and device
surface.
- Don’t to disassemble, modify or repair the device by
yourself. This may lead damage to the device. Please
send it to special authorization service center for
maintenance.
◆Temperature and humidity
Normal operating temperature +0 ° - +50 °, humidity
15% --65%.
Please place the device in a safe place.
◆Transport
4
- In the case of sudden changes in temperature or
humidity, may cause moisture condensation inside the
device, which can cause prepare a short circuit.
- Protect the device, avoid the dust or encounter
collisions in the process of transportation .
- When in transport, please use the original packaging.
◆Car adapter (car charger)
Connect the car adapter with your car cigarette lighter
socket (DC 12V or 24 V).
◆Product Overview
1. Full HD Video Recording（1920*1080@30fps）
2. 4G+1R Multi-layer filter lens, 170 degree wide angel
lens
3. 9.66 inch IPS panel（1280*320）
4. quipped with G+G capacity touch screen
5. Support WDR
6. Automatic recording when start up
7. Support loop recording( video/ audio)
8. Support continuous shooting
9. Collision file lock
5
10. Parking monitor
11. Support TF card up to 32GB
12. Support recording video while charging
◆Product structure
1 GPS 2 TF card slot 3 AV-IN
4 USB port 5 Camera Lens 6 Power
Button
7 LCD
Screen 8 Reset 9 Loudspeak
er
6
ON/ OFF Button
Function 1: Power ON/ Power OFF
Press the power button to turn the Dash Cam on. It will
automatically start recording once it receives power.
When power is turned off manually or power is removed,
the Dash Cam will save the current file and turn off.
Function 2: Background light ON/ OFF
When standby, short press the power button to enter
screen saver. Short press again to turn off the screen.
【NOTE】
A. Turn on/ff the screen will not influence the video
recording.
B. After short pressing the power button to turn off the
screen, touch the screen can wake up the screen.
◆Installation of Dash Cam
1. Turn off the vehicle engine
2. Insert the TF Card into the card slot
【NOTE】
A. Please use the high speed TF card( above class 6).
The capacity of the TF card should be no less than 4GB
7
and max to 32GB.
B. Please pay attention to the card direction when
inserting the card into the card slot.( Please refer to the
icon near the card slot).
3. Fix the Dash Cam on the original rear view mirror of
the vehicle.
4. Insert car charger into the car cigarette lighter
5. Connect the recorder's USB port to the car charger
with a charging extension cable.
[Note] The wiring extension cable can be laid along the
edge of the windshield of the car during wiring.
6.Install the rear camera on the rear of the vehicle and
pay attention to the direction when installing. Wiring can
be laid along the roof of the vehicle. After the installation
is complete, connect the rear plug to the AV-IN hole of
the recorder.
7. Adjust the lens position to ensure that the lens is level
with the ground.
8. Start the engine and check if the machine is installed
correctly.
8
【NOTE】Turn vehicles ignition to accessories, and the
Dash Cam will power ON and start recording
automatically, you will hear an audible tone once
powered.
◆Video operation
1. Turn on the vehicles’ engine, the Dash Cam will
power ON and start to recording videos.
2. In the main interface, click to enter video recording
interface, click the icon “ ” to start recording. When
the icon “ ”appears and flashed , it stops recording.
3. If need to return to the main interface, click the return
icon.
Click the “function setting” to enter setting menu. Then
click “video recording” to set video recording.
4. Power off the vehicle engine, the Dash Cam will save
the recording video files and turn off the Dash Cam
automatically. The files will be saved in the TF card piece
by piece. When the card is full, the previous files will be
covered by the later files.
【NOTE】
9
A. The recording time setting has 1/3/5min. If choose any
of it, when the TF card is full, the previous files will be
covered by the later files.
B. The files of front and rear camera will be saved
separately in the TF card. Under the catalog “DCIM”
and the folders will be named of “DCIMA” and
“DCIMB” .
◆Photo Operation
1. In the main interface, click “photo shooting” to enter
photo mode. Click the icon “ ” can take one piece of
photo.
2. If need to return to the main interface, click the return
icon “ ”.
3. In the main interface, click “ function setting” to enter
setting menu. Click the photo setting to set the photo
setting.
◆Video Playback
1. In the main interface, click “ file management” to
enter playback mode.
2. Click UP/DOWN icon to find the video/photo. Click play
10
icon “ ” to playback.
◆One button lock function
When recording, click the lock icon “ ”to lock the
present file. The locked file will have “ ” icon. To
unlock the file, click unlock icon “ ”. The locked file will
not be covered.
◆One button mute function
In the main interface or video recording mode, click the
icon “ ” to turn on/ turn off the audio.
【NOTE】The setting will be saved automatically, the
mute function do not need to be set again when reuse the
Dash Cam.
◆Switch the cameras lens on the screen
In the video recording interface, slide right/left to switch
the front and rear camera on the screen as well as the
picture in picture mode.
◆Time/ date setting
In the main interface click “function setting” to enter
function setting interface. Click the function setting to
enter the general setting. Click time/date to set the time/
Tabla de contenidos
Otros manuales de Cámara de salpicadero de Anytek
