Antec P193 V3 Manual de usuario

P193 V3

SER

’

ANUAL

ABLE OF

ONTENTS

NTRODUCTION

1.1 Case Specifications. .. .. 3

1.2 Diagram . . 3

ARDWARE

NSTALLATION

UIDE

2.1 Setting Up . . 4

2.2 Power Supply Installation 4

2.3 CP Series Power Supply Mount .. 5

2.4 Cable Management . 5

2.5 Motherboard Installation.. . 5

2.6 Internal 3.5” Device Installation . 6

2.7 External 3.5” Device Installation 7

2.8 External 5.25” Device Installation . 7

2.9 Internal 2.5” Device Installation . 8

ONNECTING THE

RONT

I/O

ORTS

3.1 USB 2.0 Ports . . 9

3.2 USB 3.0 Port . . 9

3.3 AC’97 / HD Audio Ports . 9

3.4 Switch and LED Connectors 10

3.5 Rewiring Motherboard Header Connections 10

OOLING

YSTEM

4.1 TriCool™ Fans . 11

4.2 Optional Fans. . 12

4.3 Washable Air Filters .. . 13

P193

SER

’

ANUAL

At Antec, we continually refine and improve our products to ensure the highest quality. It’s possible

that your new case will differ slightly from the descriptions in this manual. As of the date of

publication, all features, descriptions, and illustrations in this manual are correct.

Dis

laim

This manual is intended only as a guide for Antec’s computer enclosures. For more comprehensive

instructions on installing the motherboard and peripherals, please refer to the user’s manuals that

come with those components.

The P193 does not come with a power supply unit (PSU). Make sure you choose a power supply that is

compatible with your computer components and has a long enough power harness to reach your

motherboard and peripheral devices. We recommend our CP Series, TruePower Series or Signature

Series power supplies for the latest ATX specification compliance, broad compatibility, and energy-

saving capability.

Although care has been taken to prevent sharp edges in your Antec case, we strongly recommend

taking the appropriate time and care when working with it. Avoid hurried or careless motions. Please

use reasonable precaution.

This manual is not designed to cover CPU, RAM, or expansion card installation. Please consult the

motherboard manual for specific mounting instructions and troubleshooting. Before proceeding,

check the manual for your CPU cooler to find out if there are steps you must take before installing the

motherboard. While installing hardware, keep your case on a flat, stable surface.

1.1 C

ASE

PECIFICATIONS

Case Type

Advanced Mid Tower

Color

Gunmetal Gray

Dimensions

20.3" (H) x 8.1" (W) x 23.3" (D)

514 mm (H) x 241 mm (W) x 590 mm (D)

* Actual clearance for width is 9.5” / 241 mm due to the side panel fan

Weight

43.2 lbs / 19.6 kg

Cooling

1 x Rear 120

mm TriCool

™

exhaust fan

-2 x Top 140 mm exhaust TriCool™ fan

-1 x Side 200 mm Big Boy 200™ fan for dual video cards

-1 x Lower (optional) chamber 120 mm TriCool™ fan

-1 x Front (optional) 120 mm fan mount for HDD

-1 x Middle (optional) 120 mm fan mount for video cards

rive Bays

Drive Bays:

-4 x External 5.25” drive bays

-1 x External 3.5” drive bay

-6 x Internal 3.5” drive bays

-2 x Internal 2.5” drive bays

Expansion Slots 7

Motherboard Size

Mini-ITX, microATX, Standard ATX, Extended ATX

Front I/O Panel

2 x USB 2.0

1 x USB 3.0

AC’97 / HD Audio In and Out

IAGRAM

1. Rear 120 mm TriCool™ fan

2. Top 140 mm TriCool™ fans

3. 200 mm side Big Boy 200™ fan

4. Washable air filters

5. Motherboard mount

6. Power supply mount

7. 5.25” drive bays

8. 3.5” hard drive bays

9. Front I/O panel

ARDWARE

NSTALLATION

UIDE

ETTING

1. Place the case upright on a flat, stable surface with the

rear of the case facing you.

2. Remove the thumbscrews from the right side panel.

Grip the panel at the top and bottom and slide it toward

you to open the case.

3. Remove the screws from the left side panel. Grip the

panel at the top and bottom and slide it toward you to

remove the left side panel.

Note: Do not use your fingernails to pry or lift the

panels.

Inside the case you should see two separate chambers: the upper chamber for the motherboard,

externally accessible drives and hard drives; and the lower chamber for the power supply and hard

drives. You will also find some wiring with marked connectors (USB, PWR, etc.), the installed I/O panel,

a box containing one set each of drive rails for a 5.25” drive and a floppy disk drive, and a tool box

attached to the upper HDD cage containing more hardware (screws, brass standoffs, spare silicone

grommets, etc.).

OWER

UPPLY

NSTALLATION

Most power cables can be routed behind the motherboard through the cable management

compartment. If some cables can’t reach, run them through the passage that goes straight into the

motherboard compartment.

1. Remove both side panels.

2. If you are installing an Antec CP series power supply, you will need to

remove the PSU adapter plate.

3. Slide the power supply into the case. If not routing cables through the

cable management compartment behind the motherboard, route

cables through the covered opening. This will save a few inches of

cable travel and help improve airflow in the power supply

compartment.

Note: Power supplies with fans on the bottom will need to be

mounted so that the fan is facing the top of the case. There are

mounting holes for power supplies to be installed upside up or

upside down.

4. Secure the power supply by fastening it to the back of the case with

the provided screws.

ERIES

OWER

UPPLY

OUNT

Your Antec P193 enclosure

comes with a power supply mounting

adapter to mount either a standard-size power supply or the unique

Antec CP Series high-performance power supply. This adapter is

mounted to the chassis with standard Phillips-head screws. In order to

install the CP Series power supply, remove the mounting plate first.

ABLE

RGANIZERS

There is a cable management compartment between the motherboard and right side panel. You can

tuck or route excess cables in this compartment.

1. Remove both side panels.

2. Choose the cables you would like to pass through the holes behind the motherboard tray and pull

them out of the power supply chamber toward the right side of the case.

3. Use the cable ties provided to hold them in place.

4. Feed the cables back through the insertion point nearest the destination of the cable. Connect the

cable and then pull the slack back to the right side of the case.

OTHERBOARD

NSTALLATION

1. Lay the case down, with the open side facing up. The

drive cages and power supply should be visible.

2. Make sure you have the correct I/O panel for your

motherboard. If the panel provided with the case isn’t

suitable, please contact your motherboard

manufacturer for the correct I/O panel.

3. Align your motherboard with the standoff holes and

remember which holes are lined up. Not all

motherboards will match with all the provided holes;

this is normal and won’t affect its functionality.

4. Remove your motherboard by lifting it up.

5. Install standoffs as needed and put the motherboard

back in.

6. Screw in your motherboard to the standoffs with the

provided Phillips-head screws.

Note: The P183 comes with a CPU cutout on the motherboard tray, which will allow you to change

your CPU heatsink without removing the motherboard.

NTERNAL

3.5”

EVICE

NSTALLATION

With the front bezel facing you, swing the front door open. It can swing 270º so the door is parallel with

the side of the case. You can see there are four 5.25” and one 3.5” external drive bays. Inside the case

there are two 3.5” drive cages, which can house up to six hard drives.

Note: We recommend using the lower HDD cage to maximize cooling and quiet computing.

Upper HDD Installation

1. Remove the thumbscrew holding the upper HDD cage.

2. Pull the HDD cage from its position by pulling the ring toward you.

3. There are two HDD trays inside the cage. Squeeze the metal clips on each side of the tray and slide

the tray out.

4. Mount your hard drive into the drive tray with the special screws provided. Don’t over-tighten the

screws as this will reduce the vibration and noise dampening ability of the silicone grommets.

Note: Always mount the HDD with the thicker side of the silicone grommets facing up.

5. Slide and lock the tray back into the cage.

6. Slide the cage back into the case and fasten the thumbscrew.

7. Find the right Molex or SATA connector on the power supply and connect it to the hard drive.

8. Repeat the same procedure for the other drives.

Lower HDD Installation

1. Remove the thumbscrew holding the lower HDD cage.

2. Pull the HDD cage from its position by pulling the ring towards

you.

3. You can mount up to four hard drives inside the cage. They are

mounted vertically with the silicone grommets sitting at both

sides.

4. Mount your hard drive into the drive cage with the special screws

provided. Don’t over-tighten the screws as this will reduce the

vibration and noise dampening ability of the silicone grommets.

Note: Always mount the HDD with the thicker side of the silicone

grommets facing up.

5. Slide the cage back into the case and fasten the thumbscrew.

6. Find a Molex or SATA connector on the power supply and connect

it to the hard drive.

XTERNAL

3.5”

EVICE

NSTALLATION

There is one external 3.5” drive bay.

1. Carefully remove the plastic drive bay cover and metal plate covering the drive bay.

2. Find a pair of 3.5”drive rails in the hardware kit box.

3. Mount the drive rails onto the sides of the 3.5” device. Make sure the metal portion is angled on

the outside and facing forward.

4. Slide the device into the drive bay until it clicks into place.

5. Connect a small 4-pin connector from the power supply to the 4-pin connector on the floppy drive.

XTERNAL

5. 5”

EVICE

NSTALLATION

There are four 5.25” drive bays and 8 drive rails.

1. Carefully remove the plastic drive bay cover / filter and metal

plate covering the drive bay.

2. Mount the drive rails onto the sides of the 5.25” device. Make

sure the metal portion of the rail faces the front of the drive.

3. Slide the device into the drive bay until it clicks into place.

4. Mount the other devices accordingly.

5. Connect the appropriate Molex or SATA power connector from

the PSU to the power connector on the device.

NTERNAL

.5”

EVICE

NSTALLATION

Your case has two HDD trays in the upper HDD cage that can each support one 2.5” device. Note that

installing a 2.5” device in one of these trays will make it unavailable for 3.5” device use.

1. Remove the thumbscrew holding the upper HDD cage.

2. Pop the pull-ring free from its holder. Remove the HDD cage

from its position by pulling the ring toward you.

3. There are two HDD trays inside the cage. Squeeze the metal

clips on each side of a tray and slide the tray out.

4. There are four silicone grommets pre-installed on the tray.

Re-configure them for a 2.5” device by moving all 4

grommets to their positions on the inside of the tray.

5. Mount your hard drive into the drive tray with the special

screws provided.

Note: Always mount the silicone grommets with the thicker

side of the silicone grommets facing up, and place the

hard drive on top. Don’t torque or over-tighten the

screws, as this will reduce the vibration- and noise-

dampening ability of the silicone grommets.

5. Slide and lock the tray back into the cage.

6. Slide the cage back into the case and fasten the

thumbscrew.

7. Find the right Molex or SATA connector on the power

supply and connect it to the hard drive.

8. Repeat steps 3-5 for an additional 2.5” drive if applicable.

Signal

Names

Signal

Names

USB

Power

USB

Power

Negative

Signal

Negative

Signal

Positive

Signal

Positive

Signal

Ground

Key

(No

Connection)

Empty

Signal

Names

(HDA)

Signal

Names

(AC’97)

MIC2

MIC In

AGND

GND

MIC2

MIC Power

AVCC

FRO-R

Line

Out

(R)

MIC2_JD

Line

Out

(R)

F_IO_SEN

Key (no pin)

FRO-L

Line

Out

(L)

LINE2_JD

Line

Out

(L)

ONNECTING THE

RONT

I/O

ORTS

3.1

USB

Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check the

motherboard manual to ensure that it matches the table below:

USB

3.0

There is a pre-routed cable for the front-panel USB 3.0 port. Plug the back end of this cable into an on-

board USB 3.0 port on your motherboard to enable the front USB 3.0 port.

3.3

AC'97

UDIO

ORTS

There is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High Definition Audio)

connector linked to the front panel of the case.

You can connect either the AC’97 or the HDA connector, depending on the model of the motherboard.

Locate the internal audio connectors from your motherboard or sound card and connect the

corresponding audio cable. Consult your motherboard or sound card manual for the pin-out positions.

Even if your system supports both audio standards, you may only use one connector.

1 2

9 10

Otros manuales de Accesorios de computadora de Antec

Antec

Antec SX1000II Series Manual de usuario

Antec

Antec ISK 300-150 Manual de usuario

Antec

Antec Three Hundred Manual de usuario

Antec

Antec Quiet Computing 0761345-03203-2 Manual de usuario

Antec

Antec Three Hundred Two Manual de usuario

Antec

Antec VSK-2000 Manual de usuario

Antec

Antec NSK 6000 Manual de usuario

Antec

Antec Nineteen Hundred Manual de usuario

Antec

Antec Quiet Computing 0761345-02267-5 Manual de usuario

Antec

Antec Plus1000 Series Manual de usuario

Antec

Antec OVERTURE II Manual de usuario

Antec

Antec KS-388 Manual de usuario

Antec

Antec TWELVE HUNDRED V3 Manual de usuario

Antec

Antec KS-788 Manual de usuario

Antec

Antec Perfomance PLUS600 Series Manual de usuario

Antec

Antec New Solution NSK6500 Manual de usuario

Antec

Antec SX830 Manual de usuario

Antec

Antec DF-500 Manual técnico

Antec

Antec Quiet Computing Two Hundred Manual de usuario

Antec

Antec Solo Manual de usuario

Antec

Antec ARIA Manual de usuario

Antec

Antec SONATA II Manual de usuario

Antec

Antec Nine Hundred Manual de usuario

Antec

Antec New Solution NSK 3400 Manual de usuario

Manuales populares de Accesorios de computadora de otras marcas

Motorola

Motorola ATRIX Manual de usuario

HP USB Media Docking Station Manual de usuario

Cherry

Cherry B.UNLIMITED 3.0 Manual de usuario

Logitech

Logitech IO2 Manual de usuario

ARM

ARM DSTREAM-ST Manual de usuario

Bartec

Bartec TC 7 Series Manual de usuario

Philips

Philips SPC3540 Manual de usuario

Logitech

Logitech mk220 Manual de usuario

SilverStone

SilverStone LC02 Manual de usuario

Flexispot

Flexispot ML2B Manual de usuario

Hamlet

Hamlet UNIVERSAL COVER 101 KBT2 Manual de usuario

Adam Equipment

Adam Equipment RS-485 Manual de usuario

Vivo

Vivo MOUNT-KB05-4DW Manual de usuario

Kvaser

Kvaser Memorator Professional Manual de usuario

DRC

DRC D-Imaging Manual de usuario

Sven

Sven Base 305 сombo Manual de usuario

Hama

Hama 108310 Manual de usuario

SpeechWare

SpeechWare FlexyMike FMK03 Manual de usuario