Antari DNG-250 Manual de usuario

DNG-250 Low Fog Generator

User Manual

- ENGLISH

中文

Spare Parts of

1. Fan

2. Catchment

3. Power Socket

4. Resetable Fuse

5. Rocker Switch

6. P.C Board DMX 5Pin

7. P.C Board DMX 3Pin

8. LCD-TFT

9. USB

10. Tank & tank cap

11. Fog Conducting Hose

12. Power Cord & Plug

13. Pu Tube

Thank you for choosing Antari’s DNG-250 Low Fog Generator. The machine has some

terrific new features on top of the ones of its previous version DNG-200. With the 3.5

TFT color touch panel, users can operate more easily. The dimension is exactly the same

as DNG-200, but the output volume and continuity are comprehensively increased,

hence a total up-grate in performance. No CO2 is needed for DNG-250 Low Fog

Generator; therefore, there’s no risk to human body nor environment. DNG-250 is a real

green effect machine.

Please follow these operation, safety and maintenance instructions to ensure a longer

and safe life of your DNG-250 Low Fog Generator.

Pay attention to all warning labels and instructions printed on the exterior of the machine.

Safety Instructions

If you have questions about how to operate the machine safely, please contact your local

Antari dealer for help.

Keep this device dry.

Always connect to a grounded circuit to avoid risk of electrocution.

Before connecting the machine to power, always check the voltaged indicate on the

machine matches to your local AC voltage. Do not use the machine if AC power

voltage does not match.

Disconnect the machine from AC power before servicing and when not in use.

If the supply cord is damaged, contact your local Antari dealer for replacement.

This product is for indoor use only! Do not expose to rain or moisture. If fluid is

spilled, disconnect AC power and clean with a damp cloth. If fluid is spilled onto

electronic parts, immediately unplug the machine and contact your local Antari

dealer for advice.

No user serviceable and modifiable parts inside. Never try to repair this product, an

unauthorized technician may lead the machine to damage or malfunction.

For adult use only. Children being supervised not to play with the machine. Never

leave the machine running unattended.

The machine is not to be used by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge.

Installed in a well ventilated area. Provide at least 50 cm space around the machine.

Never add flammable liquid of any kind to the machine.

Make sure there are no flammable materials close to the machine while operating.

Only use Antari fluid. Other fluid may lead to heater clog and malfunction.

If the machine fails to work, unplug the machine and stop operation immediately.

Contact your local Antari dealer for .

Before transporting the machine, make sure the fluid tank is completely drained.

Smoke fluid may present health risks if swallowed. Do not drink smoke fluid. Store it

securely. In case of eye contact or if fluid is swallowed immediately look for medical

advice.

Unpacking and Inspection

Open the shipping carton and verify that all equipment necessary to operate the system

has arrived intact. If any shortage or damage due to transportation, please contact your

Antari dealer and send back with original packaging for inspection. The shipping carton

should contain the following items:

-DNG-250 Low Fog Generator

-Two power cords for connecting to Neutrik PowerCon connectors.

-3M fog conducting hose

-User's manual (item 2-4 placed in the compartment on the top of the machine)

-Water collection tray (preinstalled in the machine)

-3M PU tube, 6mmØ

Setup

The wheels at the bottom of the DNG-250 help to move the machine; wheel fixing

mechanisms are located at the diagonal line. Position the machine at a spot, press

down the fixing mechanism to prevent it from moving. To move the machine, press

the opposite side of the fixing mechanism to release it. Please note that the machine

is not allowed to place on a slope due to its big size. (refer to figure 1)

Figure

Please aim the key on the PowerCon terminal of the power cord to the slot of the

connector on the machine, plug it in and turn it about 10°clockwise until the power

cord is completely fixed. The upper power cord is for the fog generator and the bottom

one is for the compressor. (refer to figure 2 and 3)



Before connecting the machine to power supply, make sure to check the needed

voltage and watt indicated on the metal plate of the machine.

Connect the machine with the black fog conducting hose; it is a three-meter pipe. The

length of the pipe can be adjusted to fit the actual need. (refer to figure 4)

Fill Antari FLL Low Fog Effects Fluid to the tank, tighten the tank cap. (refer to figure

Figure4 Figure5

Operation

1. After confirming the voltage, connect the power cord to a grounded outlet then turn

on the lower power switch and then the higher one. The warmup starts now, and the

TFT touch panel will show the percentage of the whole warmup process until 100%

that the warmup is completed.

Figure

2. TFT touch panel introduction：

2-1 Main Menu：

2-2 Manual mode：

2-2-1 Manual mode setting：

Continuous mode ON / OFF

Output volume 20% - 100%

Manual mode

Heater status

DMX

Enforceable fluid drawing

Main menu

Heater on/off

Timer mode

Current setting of output volume

Current setting of fan speed

Manual mode setting

Start / Stop

Return

Preset 1

Preset 2

Return

2-3 Timer mode：

2-3-1 Timer mode setting:

Interval 5 secs – 200 secs

Duration 5 secs – 200 secs

Continuous mode ON / OFF

Output volume 20% - 100%

2-4 DMX：

Return

Start / Stop

Current setting of

fan speed

Current setting of output

volume

Current setting of

interval time

Current setting of duration time

Timer mode setting

Return

DMX address:

DMX status

DMX setting

Heater temperature status

Return

Current setting of fan speed

2-4-1 DMX setting：

DMX address setting

2-5 Enforceable fluid drawing:

When the tank is refilled with fog fluid, use this to draw the fluid. Press

“Pause” once the output is back to avoid damp in fog. Default duration of the

fluid drawing is 1 min.

Confirm

Cancel

Current address

Countdown

Pause

Start

Return

2-6 Heater：Heater can be activated or deactivated manually. Default setting is

activated.

2-7 Main menu：

2-7-1 DMX setting

DMX address setting. Please refer to page 8 for detail.

2-7-2 Basic information

Software version

Current working voltage (settable)

Usage time (from power on)

2-7-3 Setting

LCD brightness (Low/Medium/High/Auto)

*LCD light will shut down in 1 min when “Auto” is selected.

Action before shut down will be automatically proceeded after

warming up is finished.

Restore default setting.

Chinese/English

Software update (for Antari’s distributors’ use only)

Activate

Return

Deactivate

Heater activated

Heater deactivated

Return

DMX Connector Pin Assignment & instruction

3-1 The machine provide 3 or 5 pin XLR connector for DMX connection.

Diagram below indicate pin assignment information.

PinFunction

1 Grounding

2 Data -

3 Data +

3-2 DNG-250 DMX instruction

DNG-250 low fog generator has built-in DMX 512 function with 3 Pin and 5 Pin

sockets to choose from. After connecting to DMX, TFT touch panel can’t be used,

and all actions are controlled by DMX. Only DMX address can be entered with

TFT touch panel.

3-3 DMX 512 settings

Function

Figures

Meaning

Output Volume

0 - 4

Off

5 - 255

1 - 100%

4-1 RDM (Remote Device Management) Function

DNG-250 is equipped with RDM function which allows users to control the unit

through devices with RDM ANSI E1.20 protocol. This is a protocol enhancement

that allows bi-directional communication between a controller and attached RDM

compliant devices over a standard DMX line. Users may set, monitor and

manage the RDM supported devices and equipment in DMX network.

RDM Function

Otros manuales para DNG-250

Tabla de contenidos

Otros manuales de Máquina de niebla de Antari

Antari

Antari M-1 Manual de usuario

Antari

Antari Z-1500II Manual de usuario

Antari

Antari M-1 Manual de usuario

Antari

Antari Z-800II Manual de usuario

Antari

Antari Z-800II Manual de usuario

Antari

Antari HZ-300 Manual de usuario

Antari

Antari Ip-1000 Manual de usuario

Antari

Antari Z II Series Manual de usuario

Antari

Antari F-5D Fazer Manual de usuario

Antari

Antari F-1 Fazer Manual de usuario

Antari

Antari F-4D Fazer Manual de usuario

Antari

Antari Z Series Manual de usuario

Antari

Antari F-6 Manual de usuario

Antari

Antari M-7 RGBA Manual de usuario

Antari

Antari HZ-500 Instrucciones de instalación

Antari

Antari ICE-100 Manual de usuario

Antari

Antari Z-300II Fazer Manual de usuario

Antari

Antari Ip-1000 Manual de usuario

Antari

Antari Z-800 III Manual de usuario

Antari

Antari M-7 RGBA Manual de usuario

Antari

Antari S-120 Manual de usuario

Antari

Antari W-508 Manual de usuario

Antari

Antari Z Series Manual de usuario

Antari

Antari PM-1 Manual de usuario

Manuales populares de Máquina de niebla de otras marcas

Boost

Boost BOOST-FOG400LED-BK Manual de usuario

Home Accents Holiday

Home Accents Holiday FM1000-ASH Manual de usuario

EuroLite

EuroLite ZEITGEIST FOG-1200 Manual de usuario

Dyna-Fog

Dyna-Fog CYCLONE ULTRA 2734 Manual de usuario

PROEL

PROEL DRAGO HEAVY PLFD150HY Manual de usuario

Sparklyn

Sparklyn Y846 Manual de usuario

Magicfx

Magicfx CO2 Gun Manual de usuario

Ibiza

Ibiza LSM500LAS Manual de usuario

Venue Lighting Effects

Venue Lighting Effects ULTRA MINI-FOGGER Manual de usuario

High End

High End F-100 Manual de usuario

Chauvet

Chauvet ARENA 2100 FLEX Manual de usuario

Beamz

Beamz F1600 Manual de usuario

Sagitter

Sagitter SG ARS900C Manual de usuario

KISANKRAFT

KISANKRAFT KK-STF-480 Manual de usuario

Orion

Orion OT-U250PP Guía

Beamz

Beamz S2500 Manual de usuario

American DJ

American DJ Dyno-Fog II Manual de usuario

JB Systems

JB Systems FX 1700 Manual de usuario