ANTAIRA STE-502C Manual de usuario

2-Port Serial-Ethernet Server

STE-502C

Quick Start Guide

Version 1.3

Quick Start Guide Version 1.3

Serial to Ethernet Device Server

STE-502C

This document intends to provide customers with brief descriptions about the product and to assist

customers to get started. For detail information and operations of the product, refer to the product user’s

manual in the product CD.

Packaging

Check your package contains the following items:

STE-502C Serial to Ethernet Server

Quick Start Guide

Product CD

Wall mounting screws

2 Hardware Description

NOTE: Press the reset button of the STE-502C to reset to the default value. 0 shows the interface

Fig. 1 STE-502C interfaces

LED Indicators:

Message

Description

Off

Ethernet Disconnected

Blinking with Green

Data transmitting on Ethernet at 100Mbps

Blinking with Orange

Data transmitting on Ethernet at 10Mbps

Table 1. LAN LED Message

Quick Start Guide Version 1.3

Serial to Ethernet Device Server

STE-502C

Message

Description

Off

No data transmitting on COM port

Com 1(2)TX Blinking

Data transmitting on COM port

Com 1(2)RX Blinking

Data Receiving on COM port

Table 2. COM Port LED Message

Installation Procedures:

Step 1: Connect the STE-502C to power source

Step 2: Connect the STE-502C to the Ethernet network. Use a standard straight-through Ethernet cable

when connect to a hub/switch, or connect to a PC‘s Ethernet port via a cross-over Ethernet cable.

However, Always make sure your PC is on the same network sub-net as the STE-502C.

Step 3: Connect the STE-502C’s serial port to a serial device.

Step 4: Mount the STE-502C to a wall/panel with the screws included or Din-Rail rack (Require optional

item model: Din-Rail-Kit).

3 Software Setup

Default Network Setting: Default User Name/Password:

IP: 10.0.50.100 User Name: admin

Gateway: 10.0.0.254 Password: null (leave it blank)

Subnet: 255.255.0.0

Auto IP (Dynamic IP):

A DHCP server can automatically assigns the IP address and all the network settings. The STE-502C

supports the DHCP client function. By default, the DHCP client function on the STE-502C is disabled; you

may activate the DHCP client functions by executing monitor.exe (0)

Fig. 5 monitor.exe utility Dialog Window

Message

Description

Jumper JP1 Pin1 and Pin2 are shorted to disable AP firmware

Blinking (rate: 0.5 Sec)

AP firmware running normally

Table 3. RUN LED Message

Quick Start Guide Version 1.3

Serial to Ethernet Device Server

STE-502C

Assign a Static IP address by:

A Configuration by Telnet

1. Telnet to the STE-502C using DOS command “Telnet IP_address”. Example: telnet

10.0.50.100

2. Network, Link Mode, and COM Ports settings can be configured in the telnet window

B Configuration by Monitor.exe Utility

Use Monitor.exe on Product CD to configure the STE-502C.First click” Config” then assign a static

IP.

C. Configuration by Web Browser

1. Make sure the PC is on the same network as the STE-502C

2. Open a web browser, then Enter in the IP address as the STE-502C. The default user name is

admin and default password is null (leave it blank).

3. The STE-502C’s network, link mode and COM ports settings can be configured on different

web pages.

4. Click “Save Configuration” to save settings.

5. Click ”Restart” button to initiate the change.

4 Pin Assignments

The pin assignments of DB9 connector on the STE-502C is shown in the following table:

Pin#

RS-232

Full Duplex

RS-485

2 wire, Half Duplex

RS-485/RS-422

4 wire, Full Duplex

DCD

N/A

RXD

N/A (reserved)

TXD+

TXD

DATA+

RXD+

DTR

N/A

SG (Signal Ground)

DSR

N/A

RTS

DATA-

RXD-

CTS

N/A(reserved)

TXD-

N/A

Customer Services and Supports

1) Contact your local dealers or Antaira Technical Support Center at the following numbers.

1-877-229-3665

1-714-671-9000

2) Report the errors via website or e-mail

www.antaira.com / support@antaira.com

Otros manuales para STE-502C

Otros manuales de Servidor de ANTAIRA

ANTAIRA

ANTAIRA INJ-C200G-60-24-T-AIX Manual de usuario

ANTAIRA

ANTAIRA STE-6104C Series Manual de usuario

ANTAIRA

ANTAIRA STW-602C Manual de usuario

ANTAIRA

ANTAIRA STE-6104C Series Manual de usuario

ANTAIRA

ANTAIRA STE-501C Manual de usuario

ANTAIRA

ANTAIRA STE-708 Series Manual de usuario

ANTAIRA

ANTAIRA IS-STW6 Series Manual de usuario

ANTAIRA

ANTAIRA STE-502C Manual de usuario

ANTAIRA

ANTAIRA STE-708 Series Manual

ANTAIRA

ANTAIRA STE-604C Manual de usuario

ANTAIRA

ANTAIRA STE-6104C Series Manual de usuario

ANTAIRA

ANTAIRA ute-404k Manual de usuario

ANTAIRA

ANTAIRA STW-601C Manual de usuario

ANTAIRA

ANTAIRA STW-611C Manual de usuario

ANTAIRA

ANTAIRA STE-516C Manual de usuario

ANTAIRA

ANTAIRA STE-501C Manual de usuario

ANTAIRA

ANTAIRA STE-501C Manual de usuario

ANTAIRA

ANTAIRA STE-6104C-T Manual de usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario