Anie Jooltool Manual de usuario
1-888-337-1230 WWW.JOOLTOOL.COM INFO@JOOLTOOL.COM
by
OWNER’S MANUAL
!
POWER TOOL SAFETY RULES
Please read and understand all instructions
before using your JOOLTOOL® System
Failure to follow instructions listed below may result in serious
personal injury, electric shock and / or fire.
WORK AREA
Always secure the machine unit to a bench top
with two (2) screws using the two integrated
mounting holes, located on opposite sides of
the base of the unit.
Always work in a clean, well-lit, distraction-free work environment. Keep work
area clean and clutter free. Never work in dark areas.
Always keep bystanders, children, visitors, and all pets (animals) away from
work area while operating unit. Distractions can cause you to lose control.
Never operate tool in explosive atmospheres, such as in the presence of gases,
dust, or flammable liquids. Unit can create sparks and may ignite fumes or
dust.
Avoid vacuuming grinding debris into a canister containing wood or plastic
dust/shavings when working on any metal parts or material that can cause
sparks. Sparks can ignite inside the canister and cause fire. Disconnect vacuum
from hood/shroud when performing such work.
2
!
POWER TOOL SAFETY RULES
PERSONAL SAFETY
Avoid accidental starting. Make certain speed control switch is“OFF”before
plugging in. Leaving the speed control switch“ON”can lead to accidents.
Do not leave unit unattended. Always turn the unit “OFF” regardless of the
situation or circumstance. A running motor that is left unattended invites
accidents.
Remove all adjusting tools (keys and/or wrenches) from unit before turning
“ON.” A key or wrench that is left attached on a rotating part can cause
personal injury.
Always use common sense and pay attention to what you are doing when
using this unit. Stay alert at all times, do not use tool while tired or under the
influence of medication, drugs, or alcohol. A lack of concentration may result in
serious personal injury.
Always dress appropriately. Do not wear loose articles such as clothing,
jewelry. Hair should be contained properly. Keep loose clothes, long hair, or
jewelry away from rotating parts.
Use safety equipment: always wear eye, hand and finger protection and/or full
safety shield & fitted long sleeve clothing. A respirator is strongly
recommended for all grinding and finishing applications.Wear non-skid shoes.
Always keep proper footing and balance at all times.
Do not reach over the machine while the wheel or disc is in motion. A rotating
wheel or disc can grab any object in its path, potentially resulting in injury.
3
!
POWER TOOL SAFETY RULES
ELECTRICAL SAFETY
Always use a properly grounded 110 / 240V electrical outlet.
Always use approved electrical outlet adaptors when using the unit outside of
the U.S.A.
Never alter the plug or tamper with the converter
box in any way to fit into an electrical outlet other
than the ones described above.
Serious electrical shock and injury can occur.
Always routinely inspect the power cord for any nicks, cracks, cuts or damages.
(Make sure unit has been un-plugged prior to inspection.) If any visual or
physical damages are found, contact the manufacturer or an authorized
service center for information on replacement or repair. Refer to the warranty
page for correct instructions on returning your product, regardless if it is under
warranty or not. Do not continue to use the tool in its damaged condition,
electrical shock and injury may occur.
Never expose unit or its accessories to rain or use in damp or wet conditions.
Water or moisture entering a power tool increases the risk of electrical shock.
To avoid accidental starting, be sure switch is“OFF” before plugging in.
Plugging tool that has the switch “ON” can result in accidents.
If an extension cord is necessary, an adequate UL approved cord no longer
than 8 feet in length is recommended.This will prevent any damage to the
power adaptor or power tool unit.
SERVICE
Your JOOLTOOL System will give you great results without much maintenance.
Should it require some, it should only be performed by an authorized service
center or by the manufacturer, JOOLTOOL®. Do not attempt to repair or service
any part of the tool yourself. Doing so may result in electric shock, injury or
irreparable damage to the unit.
4
!
POWER TOOL SAFETY RULES
CLEANING
Always disconnect power from the tool before cleaning.
Always wear safety goggles when using compressed dry air for cleaning.
Ventilation openings and switch levers must be kept clean and dry.
Do not attempt to clean by inserting pointed objects through openings.
Certain cleaning agents and solvents may damage plastic parts. Some of these
are carbon tetrachloride, gasoline, chlorinated cleaning solvents, ammonia and
household detergents that contain ammonia.
GENERAL TOOL SAFETY
Staying within the tool’s designed limits will give you great results as well as a
safe & enjoyable time fulfilling your projects.Treat your JOOLTOOL™ with care.
NOTE: Always hold the workpiece with BOTH HANDS.
It is safer and will provide better control of your work.
Use only light pressure when working. Never apply excessive pressure or
torque on the disc, the spindle or any attached accessory while using the tool.
NOTE:Your JOOLTOOL™ may have an automatic “power-down”safety feature.
When excessive pressure is detected, the disc speed is reduced. If this happens,
reset your JOOLTOOL™ : turn the switch to“OFF”, unplug & replug the cord.
Always use accessories and attachments for their intended applications.
Use only Jooltool-approved accessories with this JOOLTOOL® unit.
Never use the tool with any accessories that seem damaged or excessively
worn. If in doubt, turn the tool“OFF”immediately and inspect carefully. Replace
any badly worn or broken accessories.
Always pay close attention around rotating wheels or discs. Fingers can
get hit by the spinning disc.
Never try to stop the wheels with your hands or with any object.
Allow the tool to come to a complete stop before changing attachments or
accessories.
5
!
POWER TOOL SAFETY RULES
NINJA SEE-THRU™ BACKPAD SAFETY RULES
NOTE: The rotation of the disc is COUNTER CLOCKWISE.
The motor should be completely stopped
and the switch“OFF”before installing the BACKPAD.
The BACKPAD should always be installed
with abrasive side down.
Always hold the work piece directly UNDERNEATH the disc.
Always change abrasive when there is a tear in it or if it is excessively worn.
Never reuse an abrasive once it’s been removed from the BACKPAD.
Never place workpiece on top or the side of spinning disc.The disc can eject
workpiece and may cause loss of control.
Always stop the disc if vibrating or wobbling occurs during use.
Wobbling or vibration of the disc could be caused by a damaged or
incompatible (non-JOOLTOOL™) spindle. Foreign spindles may also cause
damage to the BACKPAD. Avoid using damaged or cracked BACKPADS as they
may break apart.
Always use JOOLTOOL™ BACKPADS on your JOOLTOOL™ System with its
original spindle.This will guarantee that your discs will always be perfectly
centered and give you optimal results.
Always tighten your BACKPAD snuggly onto the spindle before use.
Never install BACKPADS while the motor is“ON”. This can cause personal injury.
6
!
POWER TOOL SAFETY RULES
ABRASIVE SAFETY - INSTALLATION & OPERATION
Always remove all protective backing film off abrasive disc before applying
onto the BACKPAD.
Always make sure all adhesive residue from used abrasive and/or dust particles
have been completely removed from the BACKPAD before applying a new
abrasive.
Always place abrasive on flat (BOTTOM) surface of BACKPAD.
Never use abrasive disc if it is not adhering
to the BACKPAD.
Never place abrasives on BACKPAD when wet.
Never cut, change, or distort the shape of the NINJA SEE-THRU ™ design on the
abrasive.
Always install abrasives on the BACKPAD by aligning correctly with the NINJA
SEE-THRU ™ design. Apply pressure to promote sufficient adherence between
abrasive and BACKPAD.
Never use disc if the abrasive has been installed incorrectly onto the BACKPAD.
Misaligned abrasive disc can increase chances of abrasive disc“catching”
during rotation.This can lead to loss of control of the workpiece and potential
damage to the BACKPAD.
7
STARTING UP
UNPACK YOUR JOOLTOOL™ SYSTEM
Make sure everything you need is there:
JOOLTOOL™ Unit
Power Cord & Adaptor
Abrasive Kit*
Instructional DVD*
Disc Retainer
HOW TO USE BACKPADS & ABRASIVES
Know what you want to accomplish and what abrasives will be required.
Always make sure the correct abrasive is used for the task. Using the right
abrasives increases your productivity, the longevity of your JOOLTOOL™ and
its abrasives as well as your workpiece.
NOTE: Always start off with a finer grit, you can go coarser later.
NOTE: Once an abrasive has been removed off the BACKPAD regardless of
condition and wear, it cannot be reused. It is recommended that all abrasives
used for a project be mounted on their own dedicated BACKPADS.This will
ensure that you get the longest life & efficiency out of your abrasives and your
JOOLTOOL™. If you require additionnal BACKPADS, please contact your nearest
JOOLTOOL™ retailer, order directly from us at 1-888-337-1230 or online at
www.jooltool.com.
8
* Your kit may be different from picture
STARTING UP
NOTE: Do not overtighten.This can cause thread to strip.
INSTALLING ABRASIVES
INSTALLING BACKPADS
INSTALLING NINJA™ CUSHION BACKING
If applied onto backpad before abrasives, these give incredible performance!
STEP 1:
Place BACKPAD
on the spindle
with abrasive
side down.
STEP 2:
Screw BACKPAD
tightly on
(clockwise) while
holding the
spindle for a
snug fit.
TURNING YOUR JOOLTOOL “ON”
Your JOOLTOOL’s power switch is also the
speed control. (Located at the bottom of unit)
To turn“ON”, simply twist the knob clockwise
to the desired speed.
To turn“OFF”, twist the knob counter-clockwise
till the motor completely stops.
STEP 1:
Remove
protective film
backing off
your 3M NINJA
Cushion.
STEP 2:
Apply firmly onto
the flat surface of
your BACKPAD,
aligning Cushion
Backing with the
NINJA Design.
STEP 1:
Remove
protective film
backing off
your 3M NINJA
Abrasive.
STEP 2:
Apply firmly onto
the flat surface of
your BACKPAD,
aligning the
abrasive with the
NINJA Design.
9
OPERATION
HOLDING THE WORKPIECE
Hold the workpiece directly UNDERNEATH the disc.
Apply the workpiece to the BOTTOM of the SPINNING
disc GENTLY and with EVEN pressure.
STAY WITHIN THE SEE-THRU AREA OF THE DISC!
DO NOT WORK OR SLIDE OFF THE EDGE OF THE DISC!
The tool’s sharp edge or tip can trim the outer edge of
disc causing damage to the disc & kick back of the tool.
When possible, work on the 3 to 6“o-clock“ portion
of the disc.This will ensure that any dust or sparks
are projected toward the vacuum port, away from you.
FINDING THE CORRECT ANGLE
!
REMEMBER!
ROTATION OF THE DISC
IS COUNTER-CLOCKWISE
DO NOT POINT ANY EDGE OR TIP TO THE
OPPOSITE OF DIRECTION OF ROTATION!
STEP 1:
Lightly make contact
with the“back”of the
tool’s edge to the disc.
STEP 2:
Lift the entire width of
the edge flat against
the disc. Hold in place.
STEP 3:
When the desired
result is achieved.
DROP TOOL DOWN.
To maintain the angle of your flat tools. Follow these steps.
10
Tabla de contenidos
