Angekis U3-5FHD6 Manual de usuario
1
CONTENT
SAFETY GUIDES................................................................................................. 2
ACCESSORIES.................................................................................................... 5
QUICK START.....................................................................................................5
PRODUCT HIGHLIGHTS..................................................................................... 5
PRODUCT SPEC................................................................................................. 6
CAMERA INTERFACE......................................................................................... 7
CAMERA DIMENSION........................................................................................7
IR REMOTE CONTROLLER..................................................................................8
VISCA IN ( RS232 PORT )................................................................................. 10
VISCA PROTOCOL............................................................................................11
PELCO-D PROTOCOL ..................................................................................... 18
PELCO-P PROTOCOL ......................................................................................19
OSD MENU...................................................................................................... 20
IR TRANSFER (IR PASS)&UVC CONTROL......................................................... 23
2
SAFETY GUIDES
1.Before operation, please fully read and follow all instructions in the manual. For your safety, always keep this
manual with the camera.
2.The camera power input range is 100-240VAC(50-60Hz),ensure the power supply input within this rate before
powering on.
3.The camera power voltage is 12VDC, rated currency is 2A. We suggest you use it with the original power supply
adapter supplied by the factory.
4.Please keep the power cable, video cable and control cable in a safe place. Protect all cables especially the
connectors.
5.Operational environment: 0℃-50 ℃, humidity less than 90%.To avoid any danger, do not put anything inside the
camera, and keep away from the corrosive liquid.
6.Avoid stress, vibration and damp during transportation, storage and installation.
7.Do not detect the camera housing and cover. For any service, please contact authorized technicians.
8.Video cable and control cable should be individually shielded, and cannot be substituted with other cables. Do not
direct the camera lens towards strong light, such as the sun or the intensive light.
9.Use a dry and soft cloth to clean the camera housing. Applied with neutral cleaning agent when there is need to
clean. To avoid damage on the camera lens, never use strong or abrasive cleaning agents on the camera housing.
10.Do not move the camera by holding the camera head. To avoid mechanical trouble, do not rotate the camera head
by hand. NEVER MOVE THE CAMERA MANUALLY WHEN IT IS WORKING.
11. Put the camera on fixed and smooth desk or platform, avoid leaned installation.
12. Power Supply Polarity (Drawing)
3
DO NOT use hands for catching; or moving the camera barrel,
otherwise it may damage the camera mechanical structure
DO NOT use hands to quick rotate the camera barrel, otherwise it
maydamage the camera mechanical structure, even break the motor driving.
4
ACCESSORIES
Check all bellow items when open the package:
Camera······················································································ 1 PCS
Power Adapter·············································································1 PCS
Power Cable················································································ 1 PCS
RS232 Control Cable······································································ 1 PCS
USB3.0 Cable··············································································· 1 PCS
Remote Controller·········································································1 PCS
User Manual··············································································· 1 PCS
Double-sided Adhesive··································································· 1 PCS
QC certification············································································ 1 PCS
QUICK START
1. Check all cable connections before power on.
5
2.DIP Switch Setting(at the bottom of the camera):
PRODUCT HIGHLIGHTS
3 cables in 1 design: video, control & power and be transited via signal USB3.0 cable.
(Notice: to achieve stable power supply via USB3.0 cable, we suggest only use the 3m USB3.0 cable supplied by the factory, and
the PC’s USB 3.0 port can supply more than 5V 1000mA power;
We suggest you connect to the power adapter(supplied by the factory) if the camera is connecting to a USB2.0 port or USB 3.0
extender cable)
Smart and fashion design, ideal for cloud-based conferencing
Adopts advanced DSP, 1/2.8 inch 5MP image sensor, and high quality 5X 90 degree FOV optical lens,provides
fluent and crystal image quality
Fast switching between different video formats: less than 1 second
5X Optical Zoom + 2X Digital Zoom
Fast and accurate focus performance
Easy firmware upgrade-(field-upgradable)
USB 3.0 supper speed output, USB 2.0 compatible
Effective RS232/485 serial control
Up to 128 presets
Compatible with the majority of video conferencing software (UVC protocol standard)
With powerful functional remote controller
IR transfer/IR pass function：except receiving the camera remote controller signal, the camera can also receive
other codes’ IR remote control signal, and pass these IR control signal to the codec’s IR receiver (via VISCA
port)
Muti-language OSD menu: English, Chinese
Dial Switch（ARM）
SW-1 SW-2 Instruction
1 OFF OFF Updating mode
2 ON OFF Debugging mode
3 ON ON Working mode
Dial Switch（USB）
SW-5 SW-6 Instruction
1 OFF OFF Updating mode
2 ON OFF Debugging mode
3 OFF ON Undefined
4 ON ON Undefined
6
TECHNICAL SPEC
Video Format
USB3.0
1080P60/50/30/25, 720P60/50/30/25,
1024x576@30,960x540@30,640x360@30,352x288@30
USB2.0 1024x576@30,960x540@30,640x360@30,352x288@30
Video Port USB3.0, USB2.0
Sensor 1/2.8 inch high quality 5MP CMOS sensor
Lens F3.1～15.5mm(5X), F1.8 – 2.8, Field of view:90°(wide)-20°(tele)
Pan/tilt Rotation Pan: ±170° ; Tilt: -30° ~ +90°, support up-side down installation
Pan/tilt Speed Pan: 0.1°~120°/s ; Tilt: 0°~80°/s
Preset: 10 via remote setting:; 128 via VISCA control; Preset ccuracy: 0.2°
Control Port RS232/RS485、USB3.0/ USB2.0
Minimum Lux 0.01lux
White Balance Auto/ Manual/Auto Tracking/OnePush/ Indoor/Outdoor/Sodium Lamp /Flurescent Lamp
Focus Auto / Manual
Iris Auto / Manual
Shutter Auto / Manual
WDR Supported
BLC Supported
2D Noise Reduction Supported
3D Noise Reduction Supported
Gamma Setting Supported
Mirror Image Supported
Anti Flicker OFF/ 50Hz/60Hz
Input Voltage 5V 1000Ma(USB3.0) / 12V DC 1A (Power adapter)
7
Dimension 220mm×190mm×173mm
Net Weight 1.25KG（2.8LBS）
CAMERA INTERFACE
CAMERA DIMENSION
1.Camera Lens
2.Camera Base
3.IR Receiver Panel
4.Indicator Light
5.Dial Switch
6. Tripod Screw Hole
7. Installation Hole
8. Power Indicator light(red)
9. 12V DC Power Input
10. RS232 (VISCA IN) Port
11.USB 3.0 Port
8
·IR REMOTE CONTROLLER
Video mute
Short press Video mute button to turn off the camera
and short press again to turn on.
Power Key
Under normal working mode, short press POWER key to
enter standby mode;Press it again, the camera will do
self-configuration, then go back to HOME position.It will
go to preset position if power on model has been set
before.
Address/Camera Setting Key
Set+(Cam1~Cam4): set camera’s remote control address.
Short press Cam1~ Cam4 to select the camera
Number Key
Set Presets: Set+(0~9) to set preset.
Recall Presets: Short press the (0~9)number key to
recall presets
Clear Key
Clear+(0~9):to clear the relative preset;
Long press to clear all preset
Menu Key
OK: to confirm the menu selection
Menu: enter/exit menu
Back: back to previous menu
9
F+/F-:
Set focus by manual, only valid under manual focus
mode
T/W:
Set the lens zoom rate.
Navigate Key: Up/Down/Left/Right
Under normal working mode, use navigate key to set the
pan tilt, and select values when enter OSD
Home Key:
Under normal working mode, short press Home key to
let the camera go back to home position.
Flip: Enable/Disable the picture up/down flip;
Mir: Enable/Disable the picture left/right flip;
MF: Enable manual focus model;
SHARP: Set sharpness level;
NR+/-: Set noise reduction level
Reset: Long press(3S) to reset camera;
Rev: Display camera revision;
Tabla de contenidos
Otros manuales de Cámara IP de Angekis
