Anderic RRST01.3 Manual de usuario

Tabla de contenidos

Otros manuales de Mando a distancia de Anderic

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación

Anderic® RRST01.3 Advanced Universal

Operating Guide

Thank you for purchasing the Anderic RRST01.3 universal remote control. This remote is

programmed to work with Roku® Media Players and LG®/Vizio® TVs (for the keys: ‘Power,’ ‘Mute,’

‘Vol+/-’). This remote can be programmed to work any TV via the learning method. Please refer to

the “Learning Instructions” section for instructions, no codes needed. However, if you have a

Roku TV, you can program this remote work via the below table “Programming Codes for Roku

TVs.”

NOTE: This remote does not work for Roku Sticks

Downloadable (PDF) version of this manual is available at:

ANDERIC.COM/RRST01

Installing batteries and the wrist strap

Please see the diagram below.

1. Remove the battery cover.

2. Insert the batteries, as shown in the diagram below, matching polarities.

3. Loop the wrist strap around the screw hole and hold in place while

replacing the battery cover.

Programming Codes for Roku TVs

Use the codes below to program to Roku TVs (TVs manufactured by one of the

brands below with built-in Roku software).

Steps:

1. Take note of the two keys to press from the “Code” column corresponding

with your TV brand from the “Brand” column.

2. Press & hold the two keys for about 5 seconds until the indicator light

flashes three times. It is now programmed.

Note: If the first code you use does not work, try the other brands as well, one of

them will most likely work.

Brand

Code

Roku Streaming Players

&

Insignia (without Game key)

&

Insignia (with Game Key)

&

Haier

Hitachi

LG

Philips

RCA

Sanyo

TCL

&

Sharp

Hisense

&

Sharp (with Game Key)

&

Hitachi

&

Learning Instructions

Note: All keys on the RRST01.3 may are learnable. Original remote is needed.

This method does not require codes.

1. Press and hold the & keys simultaneously for about 5 seconds;

indicator light will illuminate brighter and remain bright. Release the keys.

2. Point the original remote control head-to-head with the RRST01.3,

aligning top edges at about 1-2 inches apart (both remotes should be

pointing at each other).

3. On the RRST01.3, Press and release the first key to be learned, the

indicator light will now flash slowly.

4. On the original remote, press and hold the key that you want to learn to

the corresponding key previously pressed on the RRST01.3. The indicator

light will flash three times to confirm and then remain on, waiting for the

next key to learn.

5. Repeat steps 2-4 to learn other keys.

6. Press & keys simultaneously to save and exit, otherwise remote

will exit automatically after 20 seconds.

Example: Learning the POWER key from an original remote to the POWER key

of the RRST01.3.

First, on the RRST01.3 press and hold & keys simultaneously for 5

seconds, release the keys (indicator light will remain on and bright). Press and

release the key on the RRST01.3 (indicator light will now blink). Align both

remotes facing each other head-to-head. Press and hold the key on the

original remote until the RRST01.3 indicator light flashes three times and then

remains on. Press & keys to save and exit. The key is now

programmed to the RRST01.3 and should operate your unit.

Still having trouble, please visit Anderic.com/RRST01 for a step-by-step video.

Delete all learned keys

1. Press and hold & keys simultaneously for 3 seconds; the indicator

light will flash three times to confirm. The deletion of all learned keys is

now complete.

Reset to factory default status

1. Press and hold & keys simultaneously for 3 seconds; the

indicator will flash three times to confirm. Reset to factory default is now

complete.

Optional cable attachment

We offer a security cable (Part number: CBL01) that can be easily attached to

the remote. This is great for keeping your remote affixed to any flat surface. This

item is sold separately. Go to Anderic.com/CBL01 to view and purchase the item.

Copyright 2020.

Anderic® is a registered trademark of Dan’s Electronics Etc. Inc. Roku® is a

registered trademark of Roku Inc. Dan’s Electronics Etc., Inc. is not affiliated in

any way with Roku Inc. or any of the other mentioned brands. All other brands

mentioned are registered trademarks of their respective owners.

For support, go to Anderic.com.

!