Andatech ACCESSPOINT FRX Manual de usuario
Andatech ACCESSPOINT FRX
Facial Recognition Access Control System with Temperature
Screening
User Manual
Version 1.1. Updated September 2020.
INTRODUCTION
Thank you for purchasing the Andatech® Accesspoint FRX breathalyser.
The latest essential for workplaces, health facilities and public venues, the Andatech Accesspoint
FRX offers fast and accurate temperature detection and facial recognition ID to screen employees
and visitors before they even enter your premises. With the ability to be connected to any access
control system, the Accesspoint FRX can also automatically restrict access to those who are running
a fever. Equipped with power infrared thermal imaging technology, the Accesspoint FRX acts as your
premises’ first line of defence, saving valuable time, eliminating direct physical contact and reducing
the need for extra manpower when it comes to temperature screening. Combined with advanced
settings such as guest/visitor mode, mask detection and real time data upload, the Accesspoint FRX
is suitable not only for workplaces but also for schools, hospitals, restaurants, malls, and other high
traffic venues.
We hope you enjoy owning your Andatech® AccessPoint FRX breathalyser. If you have any questions
regarding the unit or want to speak with us further, please visit andatech.com.au or call 1300 800 200
(between 9am and 5.30pm Monday to Friday).
CONTENTS
DEVICE FEATURES 4
LCD SCREEN 5
SPECIFICATIONS 6
DEVICE INSTALLATION 7
GUIDELINES 7
MOUNTING THE DEVICE 8
WALL-MOUNT INSTALLATION 8
CRADLE STAND INSTALLATION 9
ANDALINK 10
SETUP INSTRUCTIONS 10
ADMIN SETUP 10
ANDALINK SYNC 10
FORCE SYNC 10
ABOUT TEMPERATURE CALIBRATION 11
TEMPERATURE CALIBRATION PROCEDURE 11
ADMIN TEMPERATURE CALIBRATION (ON DEVICE STARTUP) 11
INTERVAL TEMPERATURE CALIBRATION 11
2
MANUAL TEMPERATURE CALIBRATION 11
CALIBRATION OPERATORS 12
AMBIENT TEMPERATURE CALIBRATION 12
OPERATING INSTRUCTIONS 13
DEVICE SETTINGS 14
Network 14
Language 15
Records 16
Voice 17
Advanced Setting 18
(a) Temperature 18
(b) Recognition / Card Scan 19
(c) Test Delay 21
Temperature Calibration 22
Calibration by ambient temperature (suitable when the device is in a fixed position) 22
Calibration by body temperature within calibration interval 22
Manual calibration 22
TROUBLESHOOTING / WARNING DISPLAY 23
FACIAL RECOGNITION GUIDELINES 25
FAQs 26
LIABILITY FOR PROPER FUNCTION OR DAMAGE 26
WARRANTY DETAILS 27
3
DEVICE FEATURES
Optional Accessories for Cradle Stand Version:
● Simple base
● Smart base (includes wiring and output ports)
4
LCD SCREEN
5
SPECIFICATIONS
Body Temperature
Detection
32 to 42.5°C
Network
WIFI, 4G (optional), Ethernet
Accuracy
±0.3°C
Extension
Ports
1 USB, 1 RS232, 1 TTL, 1
switch signal, can connect to
electric lock and access gates
Display
8 inch TFT LCD
CPU
Cortex - A53 Octa-Core
1.4GHz
Camera
2 Mega Pixel with visible
light and infrared
EMMC
8GB EMMC 5.1
Facial Recognition
Distance
0.3 to 2m
Ambient
Conditions
Operation: -10 to 75°C
Storage: -20 to 50°C
Humidity: 20% to 95%RH
Facial Recognition
Rate
99.9%
Power
supply
Input: AC 100-240V 50-60Hz
0.8A,
Output: DC 12V 3A
Facial Recognition
Identification
Speed
300ms
Weight
1.28kg
Memory (built-in)
20,000 registered faces,
20,000 test results
Dimensions
23.7cm x 12.7cm x 1.8cm
Andalink memory
(cloud storage)
20,000 registered faces,
20,000 test results
(upgrade options
available)
Warranty
1 year
6
DEVICE INSTALLATION
GUIDELINES
● Install the device only indoors, in a covered environment.
● Install the device in a location with sufficient lighting
● Do not use the facial recognition feature under a strong light.
● Do not expose the device to the sun for a prolonged period of time.
● Do not use in locations that are subject to high humidity. Excessive humidity may cause
damage to the device's components.
● Do not install in locations with large temperature fluctuations throughout the day as this may
affect temperature calibration and body temperature results.
● Choose an installation location that has a regular, room temperature - away from direct
sunlight, excessive heat or cold air (e.g. directly facing an air conditioner). Excessively hot or
cold temperatures may affect body temperature readings.
● Use our provided power adapter- connecting it to an improper power source may damage
your equipment and lead to fire and/or damage.
● Keep the camera clean for optimum photos and facial recognition.
● Device should be installed facing directly forward with as little tilt or inclination as possible to
ensure the best body temperature results.
7
MOUNTING THE DEVICE
WALL-MOUNT INSTALLATION
If you have purchased the wall-mounted version, the wall mount bracket would have come
pre-installed onto the device.
To mount on the wall, use the appropriate screws (4) and wall anchors (4) for the type of wall material
you are mounting the device to (screws and wall anchors not provided).
1. Use a screwdriver to loosen the two screws on the sides of the bracket (image A)
2. Remove the device from the bracket by sliding the bracket up or down from the device (image
B).
3. Locate an area on the wall where you want to install the device (be sure to follow the
installation guidelines as mentioned before). Using a pencil and the bracket as a guide, mark
the 4 holes that will need to be drilled into the wall.
Note: The bracket can be positioned in either orientation depending on how you want to
position the wire cable (image D).
4. Drill the 4 holes on the wall and put the wall anchors inside the holes.
5. Position the flat side of the bracket against the wall and use screws to secure it into place
(image C).
8
6. Hang the device onto the bracket by sliding it up or down onto the bracket (image E).
7. With a screwdriver, tighten the two screws on the sides of the brackets to secure the device
into place (image A).
CRADLE STAND INSTALLATION
1. Mount the device and cradle stand on the surface.
2. On the under side of the surface, put the neoprene O ring inside the hexagon nut and screw it
onto the cradle stand until the device is securely positioned in place.
3. Use a torx screwdriver to adjust the angle of the display panel. The angle can be changed up
to ±30°.
9
ANDALINK
The Andalink is a secure, cloud-based software that bridges the AccessPoint FRX with a complete
data management system. With Andalink, company and OH&S managers can register users and
faces, as well as view, download, and manage reports for their employees' attendance and
temperature results. The AccessPoint FRX can also be used with visitor or guest mode, perfect for
conducting temperature screening and automating entrypoint access in public places and high traffic
areas such as hospitals, government buildings, tourist attractions and schools.
SETUP INSTRUCTIONS
For instructions on how to set up your Andalink account for your AccessPoint FRX, please visit
andatech.com.au/andalink-manual and log in with the credentials provided in the letter with your
device during purchase.
ADMIN SETUP
Important: Before operating the AccessPoint FRX, log in to your Andalink account and create at least
one (1) staff that has the user type Admin for each location/device.
An Admin staff is required to conduct the Admin Temperature Calibration on the device during startup.
ANDALINK SYNC
Test results from the device are synced to Andalink immediately (as long as there is an active internet
connection on the device).
All other changes from Andalink to the device are synced every 10 minutes.
FORCE SYNC
To Force Sync the device with Andalink, connect a mouse to the device.
Then click and hold the cursor on the version number (displayed on the bottom right of
the device screen).
The server (cloud) icon will start rotating and display a downward arrow icon to indicate
that it is syncing.
The Force Sync is complete when the icon stops rotating. The number beside the icon will be updated
to show the updated number of registered faces synced from Andalink, and a pop-up message will
appear in the Notification Area that the Force Sync is complete.
10
Tabla de contenidos
