Analytic Systems BCA1550MW Manual de usuario

INSTALLATION &

OPERATION MANUAL

BCA1550MW

AC SOURCE

BATTERY CHARGER

101-8128 River Way, Delta B.C. V4G 1K5 Canada T. 604.946.9981 F. 604.946.9983 TF. 800.668.3884 (US/CANADA)

www.analyticsystems.com

An ISO9001:2015 Registered Company Battery Chargers •Inverters •Power Supplies •Voltage Converters

Revised -Jan 31, 2023

SAVE THESE INSTRUCTIONS — This manual contains important safety and operating

instructions for the battery charger.

BATTERY CHARGER PRECAUTIONS

1. Do not expose the battery charger to rain or snow unless it is a sealed model.

2. Use of an attachment not recommended or sold by the battery charger manufacturer may

result in a risk of re, electric shock, or injury to persons.

3. Do not disassemble the battery charger; return it to the manufacturer or an authorized

service center when service or repair is required. Incorrect reassembly may result in a

risk of electric shock or re. Voltages in excess of 350 volts are present inside the charger

anytime it is plugged into an AC outlet, even if it is switched off.

4. To reduce risk of electric shock, unplug the battery charger from the AC outlet before at-

tempting any maintenance or cleaning. Turning off controls will not reduce this risk.

5. Never place battery charger directly above battery; gases from battery will corrode and

damage battery charger.

6. Never allow battery acid to drip on the battery charger.

BATTERY SAFETY

1. WARNING — RISK OF EXPLOSIVE GASES

i. WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES

GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS

REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE SERVICING

EQUIPMENT IN THE VICINITY OF THE BATTERY, YOU READ THIS USER GUIDE AND

FOLLOW THE INSTRUCTIONS EXACTLY.

ii. To reduce risk of battery explosion, follow these instructions and those published by

the battery manufacturer and manufacturer of any equipment you intend to use in

vicinity of battery. Review the cautionary marking on these products.

2. PERSONAL PRECAUTIONS

i. Someone should be within range of your voice or close enough to come to your aid

when you work near a battery.

ii. Have plenty of fresh water and soap nearby in case battery acid contacts skin,

clothing, or eyes.

iii. Wear complete eye protection and clothing protection. Avoid touching eyes while

working near battery.

iv. If battery acid contacts skin or clothing, wash immediately with soap and water. If acid

enters eye, immediately ood eye with running cold water for at least 10 minutes and

get medical attention immediately

AC SOURCE BATTERY CHARGER

IMPORTANT SAFETY INSTRUCTIONS

MEDICAL EQUIPMENT NOTICE

Analytic Systems does not recommend the use of their products in life support

applications where failure or malfunction of this product can be reasonably expected to

cause failure of the life support device or to signicantly affect its safety or effectiveness.

Analytic Systems does not recommend the use of any of its products in direct patient

care. Examples of devices considered to be life support devices are neonatal oxygen

analyzers, nerve stimulators (whether used for anesthesia, pain relief, or other purposes),

auto-transfusion devices, blood pumps, debrillators, arrhythmia detectors and alarms,

pacemakers, hemodialysis systems, peritoneal dialysis systems, neonatal ventilator

incubators, ventilators for both adults and infants, anesthesia ventilators, and infusion

pumps as well as any other devices designated as “critical” by the U.S. FDA

DANGER: Never alter the AC power cord or plug provided. If it will not t the output, use

an approved adapter or have the proper AC power cord installed by a qualied electrician.

Improper connection can result in the risk of electric shock.

i. NEVER smoke or allow a spark or ame in the vicinity of a battery.

ii. Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark or

short-circuit the battery or other electrical part that may cause a re or explosion.

iii. Remove personal metal items such as rings, bracelets, necklaces, and watches when

working with a lead-acid battery. A lead-acid battery can produce a short- circuit current

high enough to melt metal, causing a severe burn.

iv. NEVER charge a frozen battery.

v. If it is necessary to remove a battery from service, always remove grounded terminal from

battery rst. Make sure all accessories connected to the battery are off, to prevent an arc

when reconnecting the new battery.

vi. Be sure area around battery is well ventilated.

vii.Clean the battery terminals. Be careful to keep corrosion from coming in contact with eyes

viii.Study all the battery manufacturer’s specic precautions such as removing or not removing

cell caps while charging and recommended rates of charge

GROUNDING AND AC POWER CORD CONNECTION INSTRUCTIONS

The plug must be plugged into an outlet that is properly installed and grounded in accordance

with all local codes and ordinances.

Revised - Nov 10,2022

TABLE OF CONTENTS

• Front Cover, Product Photo and Title

• Product Warnings and Advisories

• Table of Contents

• Introduction

• Main Parts/Box Contents

• Operation

• Operational Indicators

• Charging Proles

• Installation

• Battery Temperature Sensor

• Equalize Cycle

• Troubleshooting

• Specications

• Warranty

Introduction

The BCA1550MW AC-source battery charger provides up to 1500 watts of precision charging

power to charge up to two connected 24V bank battery systems.

Internally, the recently updated design incorporates a Power Factor Corrected (PFC) input

stage allowing the charger to run continuously from 85 – 264 VAC at 50 or 60 Hz with a Power

Factor of 0.99 or better from 10% to 100% load. Heavy input and output ltering reduces EMI

to extremely low levels to prevent radio interference.

These units are constructed with a heavy-duty extruded aluminum chassis and heavy gauge

aluminum front and rear panels with thermostatically controlled cooling fans and all stainless

steel fasteners for rugged duty. These units feature IP66 rated construction.(IP67-rated

construction with certication and testing also available). Additionally military ruggedization

upgrades include MIL-spec connectors, expanded operating temperature and shock and

vibration protection.

Reliability features of this product line include LED status indicators, input circuit breaker,

thermal shutdown, current limiting, reverse polarity battery connection protection, output short

circuit shutdown with automatic recovery and output over-voltage protection.

Box Contents

The box you have received should contain the following:

• One BCA1550MW AC Battery Charger

• One Battery Temperature Sensor

• This Manual

• One Warranty Card

If anything is missing or damaged please contact your dealer or Analytic Systems for a replacement

Main Parts

1. Battery Temp. Sensor Connection:

PT07A8-4S MIL-Spec Connector

2. DC Output Connection: MS3102E22-

22S circular MIL-Spec Connector

3. Output Voltage Adjust

4. Indicator LEDs

5. Stage Select Switch

6. Power Switch

7. AC Input Connection:

D38999/20WC4PN MIL-Spec Connector

8. Equalize Cycle Start Button

FRONT PANEL

Operation

This unit is designed for simple and intuitive operation. Before operating, make sure this unit

is properly installed and connected. See Installation for more information.

TO CHARGE A BATTERY

1. Check that the Battery Reversed B1 and B2 LEDs are OFF. If either are glowing, check the

battery connection to insure it is in the correct polarity.

2. Select the type of charging prole using the Stage Select switch on the front panel.

See Charging Proles for more information.

3. Move the Power Switch to ON. The alarm buzzer will sound and the LOW VOLTAGE

OUTPUT LED will glow red briey, then the POWER LED will glow green.

4. The CHARGING LED will glow green and the unit will charge the battery at the voltage

and current listed on the label.

5. Once the battery is fully charged, the CHARGING LED will turn off. The unit will maintain

the battery at full charge for as long as it is connected.

TO ADJUST THE CHARGING (FLOAT) VOLTAGE

The Output Voltage Adjust can be use to adjust the charging (oat) voltage from the unit’s

rated output voltage in order to ne-tune its charging capabilities.

1. On W-series and Y-series models the Output Voltage Adjus tis protected by an O-ring

sealed hexagonal plug. This plug can be removed using a 5/8ths inch or 16mm wrench.

2. Move the Power Switch to ON.

3. Rotate the output voltage adjustment potentiometer on the front panel.

4. Rotating the potentiometer clockwise increases the output voltage; counterclockwise

descreases it.

5. Using a voltmeter or multimeter, check the charging voltage at the Output Connection.

Adjust until the voltage reading is suitable. If the unit has the optional digital meter, that

can be used to read the output voltage instead.

6. Replace the hexagonal plug to return the unit to water resistant condition.

TO END OPERATION

1. Move the Power Switch to OFF.

2. Wait for all the LEDs stop glowing.

3. Once all of the LEDs are off, it is safe to disconnect the unit from the power source and

battery. The unit is now ready for storage or service.

EQUALIZE

THIS FUNCTION REQUIRES THE BATTERY TEMP. SENSOR INSTALLED

This LED glows red when the unit is performing an Equalize cycle. This LED blinks red when

the unit is waiting for a battery to nish charging before performing an Equalize cycle.

BATTERY OVER TEMP

THIS FUNCTION REQUIRES THE BATTERY TEMP. SENSOR INSTALLED

This LED glows red when the battery’s temperature is above the safe limit, the unit will then

turn OFF its outputs as precaution. Once the battery temperature is within the safe operating

range, the unit will automatically resume operation

BATTERY REVERSED B1/B2

This LED will glow red when a battery is connected to Output 1/2 in reverse polarity,

respectively. Do not turn the unit ON until this is corrected, failing to do so will damage the

battery charger and is NOT covered under the Warranty.

POWER ON

This LED glows green when the unit is connected to an AC power source and turned ON.

CHARGING

This LED glows green when the unit is currently charging a battery. This LED turns off when

the connected battery is fully charged. The charger will maintain the battery at the oat

voltage for as long as it is connected.

OVERTEMP

This LED glows red when the unit’s internal temperature is above the safe limit, the unit will

then turn OFF its outputs as a precaution. Once the internal temperature is within the safe

operating range, the unit will automatically resume operation.

LOW VOLTAGE OUT

This LED glows red when the output voltage is too low to properly charge the battery, the unit

will then turn OFF its outputs as a precaution. Once the unit detects the output voltage is

within the normal operating range, it will automatically resume operation.

LOW VOLTAGE IN

This LED glows red when the input voltage is too low for proper operation, the unit will then

turn OFF its outputs as a precaution. Once the unit detects the input voltage is within the

normal operating range, it will automatically resume operation.

Operational Indicators

This unit features several indicator LEDs on its front panel to display the unit’s operating

condition. The meanings of these LEDs are detailed below. For more information on the LEDs

relating to alarm conditions, see Troubleshooting.

1110

Charging Proles

This unit has both two-stage and three-stage charging capability. You can choose which type

of charging is used during operation by using the Stage Select switch located on the front

panel. Below are explanations of the two charging proles:

1. The battery is charged at constant

current until the battery’s voltage

reaches the oat voltage.

2. The charging current diminishes as

necessary to maintain the battery at

that voltage.

TWO-STAGE CHARGING

Two-stage charging eliminates any risk of

overcharging the battery if it is connected to

a load while being charged.

THREE-STAGE CHARGING

1. The battery is charged at constant

current until the battery voltage

reaches the absorption voltage.

2. Then the charging current diminishes

as necessary to maintain the battery

at that voltage.

3. Once the charging current drops

below 10% of the rated output,

the charging cycle is complete. The

charger then switches to the oat

voltage to maintain the battery at

full charge.

Three-stage charging is more complete than two-stage, but the charging current must drop

below 10% of the rated output current of the charger for the Absorption Mode to terminate.

For that reason, three-stage charging is not recommended for charging loaded batteries

because the unit cannot differentiate between current going to a load connected to the

battery and current being absorbed by the battery, which may cause overcharging.

Tabla de contenidos

Otros manuales de Cargador de baterías de Analytic Systems

Analytic Systems

Analytic Systems BCD315MW Manual de usuario

Analytic Systems

Analytic Systems BCD180 Series Manual de usuario

Analytic Systems

Analytic Systems IBC320 Manual de usuario

Analytic Systems

Analytic Systems BCD605 Manual de usuario

Analytic Systems

Analytic Systems BCD600-32-12 Manual de usuario

Analytic Systems

Analytic Systems BCA1000R Manual de usuario

Analytic Systems

Analytic Systems BCA310MS Manual de usuario

Analytic Systems

Analytic Systems BCD615 SERIES Manual de usuario

Analytic Systems

Analytic Systems BCA1000V Manual de usuario

Analytic Systems

Analytic Systems BCD610 Manual de usuario

Analytic Systems

Analytic Systems BCH10W Manual de usuario

Analytic Systems

Analytic Systems BCD615-48-48 Manual de usuario

Analytic Systems

Analytic Systems BCD1015 SERIES Manual de usuario

Analytic Systems

Analytic Systems BCA1050 Manual de usuario

Analytic Systems

Analytic Systems BCD315-12-24 Manual de usuario

Analytic Systems

Analytic Systems BCA1505M Series Manual de usuario

Analytic Systems

Analytic Systems BCA1000 Manual de usuario

Analytic Systems

Analytic Systems BCD1015R-72-12 Manual de usuario

Analytic Systems

Analytic Systems BCD1000-110-12 Manual de usuario

Analytic Systems

Analytic Systems BCA1505 SERIES Manual de usuario

Analytic Systems

Analytic Systems BCD615R Manual de usuario

Analytic Systems

Analytic Systems BCA1505MS Series Manual de usuario

Analytic Systems

Analytic Systems BCA1505MW-24 Manual de usuario

Analytic Systems

Analytic Systems BCD600 Series Manual de usuario

Manuales populares de Cargador de baterías de otras marcas

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Manual de usuario

Enelion

Enelion Vertica Manual de usuario

RCA

RCA CHU6 Manual de usuario

ANSMANN

ANSMANN ALCT 6/24-10 Manual de usuario

Hitachi

Hitachi UC 18YRSL Guía de solución de problemas

Olympus

Olympus B-20 LPC Manual de usuario

Exibel

Exibel ZH1708143 Manual de usuario

Lenmar

Lenmar Mach 1 Manual de usuario

CTEK

CTEK MXS 5.0 Manual de usuario

ABB

ABB HT842379 Manual de usuario

Nitecore

Nitecore Superb Charger SC4 Manual de usuario

Renogy

Renogy RBC2125DS-21W Manual de usuario

Braun

Braun BWC02M Manual de usuario

CTEK

CTEK MXS 3.6 Manual de usuario

Black & Decker

Black & Decker BDV090 Manual de usuario

Trinity

Trinity DPD Manual de usuario

Hulkman

Hulkman Sigma 1 Manual de usuario

IKEA

IKEA koppla Manual de usuario