Analog way MSTC02-R2 Manual de usuario

Picturall Twin Compact -Ref. MSTC02

QUICK START GUIDE

Thank you for choosing Analog Way and the Picturall Twin Compact. By following these simple steps, you will

be able to set up and use your Powerful media server within minutes. Discover the Picturall Twin Compact

capabilies and intuive interface while commanding top-notch presentaons and unleash your creavity

for a new experience in show and event management.

• 1 x Picturall Twin Compact (MSTC02)

• 1 x Power supply cord

• 1 x Ethernet cross cable (for device control)

• 1 x USB memory sck containing soware and technical documentaon

• 1 x Rackmount kit

• 1 x User manual (PDF version)*

• 1 x Quick start guide*

* User manual and quick start guide are also available on www.analogway.com



The Picturall Twin Compact uses standard ethernet

LAN networking. To access the Web Congurator,

connect a computer to the Picturall Twin Compact

using the Ethernet cable. Then on your computer,

open an internet browser and enter the IP address

of the Picturall Twin Compact (displayed on the

front panel screen).

The connecon should start.

Oen, computers are set to DHCP client (automac

IP detecon) mode. You may need to change the

IP address conguraon on your computer before

you can connect. These sengs are found in the

properes for your LAN network adaptor, and vary

by operang system.

The default IP address on the Picturall Twin

Compact is 192.168.2.140 with a netmask of

255.255.255.0. Therefore, you can assign your

computer a stac IP address of 192.168.2.100 and

a netmask of 255.255.255.0 and should be able to

connect.

If the connecon is not starng:

• Make sure the computer IP address is on the same

network and subnet as the Picturall Twin Compact.

• Make sure that no devices have the same IP

address (prevent IP conicts)

• Make sure the network cable is CAT5 or higher.

• For more informaon, please see the user manual

or contact your local technical support.

Once successfully connected, the Web Congurator

is displayed automacally.

CAUTION!

Mounng using only the front

rack ears is sucient for xed

installaons. Addional support,

such as the rear rack support or

slide rails, is required for mobile

applicaons, and recommended

for all.





hp://bit.ly/AW-Register

WHAT’S IN THE BOX

QUICK SETUP & OPERATION





The user should avoid disconnecng the power source

(AC input) unl the unit is in stand-by mode. Failure to

do this could result in hard drive data corrupon.

Two-channel audio interface

with balanced XLR outputs (oponal)

Two DisplayPort 1.2 outputs

(4K@60Hz 10-bit)

Ethernet Plug



100-240 VAC; 8A; 50/60Hz; 405W;

internal, autoswitchable

525 GB SSD

(oponal 1 TB SSD)



- 2 x HDMI 1.4,

- 4 x HDMI 1.4,

- 1 x HDMI 2.0,

- 2 x 3G-SDI,

- 4 x 3G-SDI,

- 1 x DVI,

- 2 x DVI

To turn o, press this buon

then press the Next/Status buon to conrm

USB Plug

Display and cycle status

informaon on the OLED display

USB Plug

OLED display

USB Plug

RS232 Plug (oponal)





The operang systems must support Java version 8 for Picturall

Commander to be installed. Make sure Java version 8 is installed on

the computer before installing Picturall Commander.

Note: The latest version of Commander is automacally down-

loaded during the installaon process.

1. On the computer, insert the USB sck delivered with the media

server.

2. Copy the installer le matching the operang system from the

USB sck to the computer.

3. Run the installer le and follow the instrucons to complete the

installaon process.



In the Display conguraon menu, choose the display mode:

- Auto: follow EDID sengs

- Manual: set the output resoluon, refresh rate and connectors

manually

- : select a custom display conguraon

- Special: select a preset mode for display signal spliers (Matrox

TH2GO and DH2GO, Datapath X4 and FX4)

In Manual mode, select the output connectors, resoluon and

refresh rate for the selected GPU.

Note: Do not use mulple display devices with dierent refresh

rates as this may cause bad playback (stuering).

Tip: If using idencal displays, use the buons Copy, Paste and

Copy to all.

In the DMX conguraon menu, choose the DMX/Art-Net

sengs:

-  : Set the rst universe and the rest of the

layers will be patched to next universes. If patching more than 9

layers, the server will use several Art-Net universes.

- : Set the Art-Net subnet value (between 0 and

15).

-  : Set the rst channel of the rst universe for

layer 1.

- : Set the preferred DMX xture prole (1.1, 1.0 or

mini).

-    : Enter the number of the displays

controlled with DMX t as the acve displayed plug. (Not

necessarily displayed).

Layers are patched rst starng from a given oset on a given

universe. Layers are patched so that they do not split at the

universe border.

 

CONNECTION TO THE MEDIA SERVER

1. Connect the computer and the Media Server to the same

network.

2. Use same netmask in the server and the computer if not

using DHCP server. If DHCP server is enabled in the server, use

automac network sengs in the computer.

3. Run Picturall Commander and click on the

 tab.

4. Type the IP address of the server in the  eld or click

Locate to automacally nd the servers in the same network and

view the server versions before connecng.

5. In the Name eld, enter a name for the connecon.

6. Click  to Create the Connecon. A message conrms the

connecon to the Picturall Series Media Server.

- Launch a web browser and enter the server IP address in the

address bar. All devices default IP addresses are 192.168.2.140.

- Click   or  to access server

conguraon.



- Set the number of layers to use and patch to

Art-Net (max 200). This aects the number of available layers in

Picturall Commander.

-  Set the maximum resoluon to be

processed by the media server.

CONTROL TABS

Click  then click any menu to open the corresponding

control panel.

- : Connect and reconnect to a server pressing

Reconnect buon.

- : Transfer media les to the Picturall Series Media Server

and arrange the media library.

- : Congure the display setup.

- : Control all layer parameters. This is the main menu

for controlling the Picturall Series Media Server with Picturall

Commander.

- : Opmize the use of the GPUs.

- : Program and me cues for the show.

- : Congure test images to help when seng up the

show.

- : Check the performance and temperature of the

server.

In the Server conguraon menu, choose the network mode:

- Automac (DHCP): The server gets IP address from DHCP

server in the same network

- Automac (ARTNET): The IP address is generated based on the

Art-Net protocol

- Manual: Set the IP address and netmask manually

INSTALLATION

PICTURALL COMMANDER

For complete details and operaons procedures, please refer to the  User

Manual and our website for further informaon: www.analogway.com

01-JUN-2019

MSTC02 - QSG

Code : 140193

This Analog Way product has a 3 year warranty on parts and labor, back to factory. This warranty does not

include faults resulng from user negligence, special modicaons, electrical surges, abuse (drop/crush),

and/or other unusual damage. In the unlikely event of a malfuncon, please contact your local Analog Way

oce for service.

MEDIA

DISPLAYS

CUES

WARRANTY AND SERVICE

PICTURALL COMMANDER STRUCTURE



- Import media les via drag and drop le.

- Encode to PRKL format for best

performance.

- Add web pages and video streams.

- Arrange medias in collecons (playlists).

- Set displays to match the conguraon.

- Follow the display wizard to create

Blendings.

- Use Cropping and Color correcon and

Angle correcon.

- Opmize GPUs performance

- Use Cues to save presets for several

layers.

- Create sequences for the show.

- Set Wait, Fade and Hold mings for the

Cues.

- Organize Cues in Stacks.

- Use Playbacks to play the Cue Stacks.

LAYERS

- Place the layers in the pixel canvas.

- Put medias in layers and play them.

- Set play mode end acon (Stop, Loop, etc.).

- Use various eects (rotaon, keying, cut

and ll, etc.).

- Use Macros to save sengs for one layer.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Servidor de Analog way

Analog way

Analog way MSQ04-MkII Manual de usuario