AMT Crono S-PID 30 Instrucciones de funcionamiento

Crono S-PID 30

Short Programming Guide - Flow Mode (mL/hr)

Pump activation and mode selection

The default delivery setting for the S-PID 30 is timed mode. This allows

programming of the duration of infusion. To change the mode of operation

remove and then replace the battery.

The pump will perform a short self test procedure during which a full screen

display of all elements should appear.

When the symbol [-t-] is displayed, press and hold the [P] button until the

display flashes. Press the [-] button until the display changes to [-F-]. Press

[P] to confirm and the pump will switch to [OFF] mode.

.Locking/unlocking the keypad

By default keyboard lock is not activated on this device.

With the pump displaying [OFF] press the (-) key for approximately 7

seconds. A number representing the number of completed infusions will

appear on the screen.

While still holding the [-] key depress the [+] key.The screen will display

flashing [L.0] and the keyboard is unlocked.

Use the (+) or (-) button to select required value. (L1 is on, L0 is off)

Caution: Users must familiarise themselves with the full user instructions.

These notes provide only a reminder of main functions.

This symbol will display when the keyboard is locked.

SG008/19BM

Start the infusion by pressing the [+/ON] button.

You are given the option to prime the infusion set [Pr]. Press and hold

the [P] button to deliver the required prime up to a maximum of 1.5mL.

Press the [+] button again to start the infusion at any time.

To change the infusion rate press the [+] button to display the current

flow rate . Press the [-] key until the screen symbols flash, and then

press the [+] button to increase, or the [-] button to reduce, the infusion

rate.

After 5 seconds this will be locked into the pump memory.

At the end of an infusion the plunger will automatically return to its

programmed start position

To return the plunger earlier, switch the pump into [StoP] mode by

pressing the [+] and [-] keys together. Then press the [P]and [-]

buttons together until [END] appears on the screen.

The syringe rubber plunger will not be withdrawn with this procedure.

With the keyboard unlocked, and the pump displaying [OFF] pressing

the [P] button will allow you to step through a menu to set the following

parameters in turn.

End of infusion alarm On/Off

Syringe Partial Volume 1ml steps

Press the [P] button to select alarm setting.

Use the (+) to set alarm on or (-) button to set alarm off

Press the [P] button to confirm value and select the partial volume

setting.

Press [-] button to reduce the volume or [+] button to increase.

Press the [P] button to confirm value and the pump will take a short

time to position the plunger at the programmed position.

Starting infusion and setting infusion time

Resetting plunger position

Programming the pump

Setting procedure

Tabla de contenidos

Otros manuales de Bomba de agua de AMT

AMT

AMT 489 Series Instrucciones de montaje

AMT

AMT Submersible Pump 12V DC Series Manual del propietario

AMT

AMT 4946-99 Instrucciones de montaje

AMT

AMT 4222-95 Instrucciones de montaje

AMT

AMT 3100-96 Instrucciones de montaje

AMT

AMT 3670-94 Instrucciones de montaje

AMT

AMT 3941-96 Instrucciones de montaje

AMT

AMT 316F-95 Instrucciones de montaje

AMT

AMT 5150-96 Instrucciones de montaje

AMT

AMT 5580 Instrucciones de montaje

AMT

AMT A200-90 Instrucciones de montaje

AMT

AMT 4381-96 Instrucciones de montaje

AMT

AMT 489G Instrucciones de montaje

AMT

AMT 5761-95B Instrucciones de montaje

AMT

AMT 490B-98 Manual de usuario

AMT

AMT 3890-99 Instrucciones de montaje

AMT

AMT 4783 Instrucciones de montaje

AMT

AMT 4660-99 Instrucciones de montaje

AMT

AMT 3930-D5 Instrucciones de montaje

AMT

AMT 4906 Instrucciones de montaje

AMT

AMT 489G-95 Instrucciones de montaje

AMT

AMT 3201-96 Instrucciones de montaje

AMT

AMT 4230-97 Instrucciones de montaje

AMT

AMT 4294-98 Instrucciones de montaje

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario