AmpliVox BELT BLASTER Manual de usuario
AmpliVox • 650 Anthony Trail Suite D, Northbrook, IL 60062 • Phone: (800)267-5486 • Fax: (800)267-5489 www.ampli.com
S206 BELT BLASTER /
S207 BELT BLASTER PRO
WAISTBAND AMPLIFIER
INCLUDED:
1. Belt Blaster Pro Personal Waistband Amplifier
2. 44″ Adjustable Belt
3. Headset and Lapel Microphone
4. AC Adapter/Recharger
5. Storage Case
6. Waistband Case
7. 6 - NiMH rechargeable batteries
S206 Batteries: Insert six (6) standard ʺAAʺ batteries (not included) as show below.
Install Batteries:
1. Locate the battery compartment on the right rear side of the amplifier.
2. Press (do not pry) the cover locking tab to the right and lift to remove battery cover.
3. Install the 6 batteries . Follow the picture of battery direction as seen in the bottom of
the holder. Negative (-) flat side of battery toward spring.
4. Insert battery cover and press back into place.
BATTERY REPLACEMENT
When batteries (S207) will no longer hold a charge, all 6 batteries MUST be replaced at the same
time. Mixing old and new batteries can lead to battery failure.
CHARGING BATTERIES FOR FIRST USE (S207)
Your new Belt Blaster Pro is shipped with 6 NiMH rechargeable batteries. Once they have been installed,
they must receive a deep charge (24 hours) before being used.
1. Insert battery charger mini plug (AC adapter) into the charging port located on the bottom of the amplifier.
2. Plug the adapter into a working power outlet. Charge the Belt Blaster Pro for 24 hours for the first charge.
After this, only 8 - 14 hour charge is necessary
.
S207 Rechargeable Batteries: The rechargeable Nickel Metal Hydride batteries of the S207 Belt Blaster Pro will have a life
expectancy of approximately 2 years. Actual life will vary significantly depending on your usage and charging habits. There may
be a time when you need to use backup power to get through a presentation. The Belt Blaster PRO was intentionally designed
to accommodate standard ″AA″ batteries for just such occasions.
NOTE:
The AC Adapter/Charger can ONLY be used to recharge the batteries . Can not power the amplifier simultaneously.
CAUTION! NEVER PLUG IN AC ADAPTER/CHARGER WITH NON-RECHARGEABLE BATTERIES INSIDE AMPLIFIER.
SERIOUS DAMAGE MAY BE CAUSED TO BATTERIES AND AMPLIFIER.
1. Belt Blaster Personal Waistband Amplifier
2. 44″ Adjustable Belt
3. Headset and Lapel Microphone
4. Storage Case
INCLUDED:
S206 S207
INSERTING/CHANGING THE BATTERIES
CHARGER PORT
AmpliVox • 650 Anthony Trail Suite D, Northbrook, IL 60062 • Phone: (800)267-5486 • Fax: (800)267-5489 www.ampli.com
OPERATING INSTRUCTIONS
The amplifier is usually worn on the front of the waist, much
like a “waist pack” . The woven nylon waist band is adjusta-
ble to 44 inches. Remember to wear the Belt Blaster so the
speaker grill faces out away from the body to avoid feed-
back.
1. With the amplifier turned OFF, insert the 3.5mm lapel/
headset microphone plug into the jack on top of the
amplifier.
2. Put the amplifier on your waist, adjust the attached belt
to fit, then clip the buckle. Please take note of the path
of the nylon belt through the clips. In the event that the
belt is disassembled, it is imperative that the belt be
correctly reinstalled.
3. Turn the amplifier ON by turning the volume control
knob to the 11 o’clock position while speaking at a con-
sistent volume level.
4. When you perceive your voice is loud enough, reduce
the volume slightly. This is done because you are
standing behind the speaker and your voice is consider-
ably louder then you perceive.
USB THUMB DRIVE
1. Insert USB Thumb Drive into the USB Slot on top of
amplifier.
2. Press ON/OFF/Play button to turn on the USB. USB
power LED will light up and flash. Press button again to
play first recorded item.
3. Press to advance to next song/message or hold for 2
seconds to fast forward.
4. Press to go back to last song/message or hold for 2
seconds to fast backwards.
TROUBLE SHOOTING
POPPING OR CRACKLING NOISE
Popping or crackling noises coming from the speaker of your Belt Blaster, particularly when the microphone cable is moved, are
usually caused by dirt, finger oils or corrosion build-up on the microphone plug.
Remove the plug and clean the metal tip and sleeve with a clean cloth or cotton swab moistened with alcohol, or with a pre-
moistened towelette (Wet Wipe or similar). If none of these are available, use a clean, dry cloth or paper towel. While not as
effective, this should still improve the contact.
ON/OFF
VOLUME
POWER/BATTERY
LOW LED MICROPHONE
JACK
Nov, 2020
TOP
USB
SLOT USB
ON/OFF/
PLAY USB
FF/FB
USB
PWR LED
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Oradores de AmpliVox
AmpliVox
AmpliVox SW800 Manual de usuario
AmpliVox
AmpliVox SW915 Digital Audio Travel Partner Manual de usuario
AmpliVox
AmpliVox S500-MH Manual
AmpliVox
AmpliVox SW720 Manual de usuario
AmpliVox
AmpliVox SW6200 Manual de usuario
AmpliVox
AmpliVox RECHARGEABLE MITY-VOX S212 Manual de usuario
AmpliVox
AmpliVox S602R Manual de usuario
AmpliVox
AmpliVox S905 Manual de usuario
AmpliVox
AmpliVox SW227 Manual de usuario
AmpliVox
AmpliVox S132A Manual de usuario
AmpliVox
AmpliVox MITY-MEG PLUS SB602MR Manual de usuario
AmpliVox
AmpliVox Mity-Lite Plus SW320 Manual de usuario
AmpliVox
AmpliVox HALF-MILE HAILER W/INTERNAL WIRELESS PORTABLE PUBLIC ADDRESS SYSTEM... Manual de usuario
AmpliVox
AmpliVox SW800 Manual de usuario
AmpliVox
AmpliVox Rechargeable Mity-Vox SW212 Manual de usuario
AmpliVox
AmpliVox Belt Blaster pro S207 Manual de usuario
AmpliVox
AmpliVox ROVING ROSTRUM S122A Manual de usuario
AmpliVox
AmpliVox S601R Manual de usuario
AmpliVox
AmpliVox SW915 Digital Audio Travel Partner Manual de usuario
AmpliVox
AmpliVox SW915 Digital Audio Travel Partner Manual de usuario
