Ampac SmartTerminal Guía

MAN1557-4

WORLD LEADER OF INNOVATIVE SOLUTIONS IN FIRE DETECTION AND ALARM SYSTEMS

SmartTerminal

Installation Commissioning & Operation

“Our aim is to provide ‘Consistently Excellent Service’ in the eyes of our customers”

Europe SmartTerminal Installation Commissioning & Operation

Page 3

Table of Contents Page No.

1Introduction................................................................................................................... 4

2Mechanical .................................................................................................................... 5

2.1 Mounting the Enclosure ................................................................................................. 5

2.1.1 Enclosure Details............................................................................................ 5

2.1.2 Fixing the Chassis to the Wall ........................................................................ 5

2.1.3 Board Removal / Replacement....................................................................... 6

2.1.4 Removing the Knockouts................................................................................ 7

3Installation & Cabling ................................................................................................... 8

3.1 SmartTerminal Termination Board Interconnection ....................................................... 8

3.2 FACP Comms ................................................................................................................ 8

4Setting the Address...................................................................................................... 9

5Setting the SmartTerminal in LoopMaster ............................................................... 10

6Operation..................................................................................................................... 12

7Controls and Indicators ............................................................................................. 13

7.1 LCD Screen Format ..................................................................................................... 17

8Specifications ............................................................................................................. 19

9Trouble Shooting Chart.............................................................................................. 20

Europe SmartTerminal Installation Commissioning & Operation

Page 4

1 Introduction

SmartTerminal has been designed for use with the LoopSense series of FACP’s.

4 line by 40 character LCD with backlight and navigation keys keys allow the

SmartTerminal to be used for FACP operation and interrogation. Note the backlight is only

energised when alarms are present, a key has been pressed or controls enable key switch is

enabled

Buzzer and system Reset.

System expansion capabilities / options:

A wide range of secure user functions. This includes the ability to disable / re-enable a large

number of system functions.

Flush or surface mountable enclosure.

Controls have tactile and audible feedback of operation.

All terminals cater for 2.5mm cables.

SmartTerminal connects to the LoopSense Fire Alarm Control Panel (FACP) via the RS485

multidrop communication port. Generally it is designed to be used anywhere where the status of the

FACP is required to be monitored by local personnel and limited control is required.

Front panel controls that allow the resetting of alarms and activation/silencing of alarm

devices. Enabling operational access to the controls is via a key-switch;

Reports events from devices that are accessible to the host FACP. For example if the host

FACP is configured with global access then the connected SmartTerminal reports events

from all devices. If the host FACP is configured as local then the connected SmartTerminal

reports events from devices that are directly connected to the host FACP.

SmartTerminal essentially consists of two PCBs;

1. SmartTerminal Termination Board. A Termination Board is mounted in each SmartTerminal

to protect and interface the RS485 communications and 27VDC supply to the LCD Board

2. BRD82ICC – Control, LCD Communications and LCD Driver Board

SmartTerminal can be supplied in two styles;

1. BX05: Slim line SmartTerminal

2. BX1: Standard SmartTerminal

Note:A maximum of 30 SmartTerminal’s may be connected to the communications bus over a

distance of approximately 1.2Kms

Europe SmartTerminal Installation Commissioning & Operation

Page 5

2 Mechanical

SmartTerminal is supplied in an ABS cabinet and consists of;

The Main Card, with all controls and indicators mounted directly onto it

1 X Termination Board

2 X ABS door keys

2 X 003 Enable / Disable keys

2 X Jumper links

The front door of the ABS version is locked by way of two clips on the right hand side of the cabinet.

A special locating key which has two raised pins that are inserted into the side of the cabinet unlocks

the door.

DOOR RELEASE PINS

Figure 1: ABS Door Key

2.1 Mounting the Enclosure

The panel MUST be mounted in an area that is NOT subject to conditions likely to affect its

performance, e.g. damp, salt-air, water ingress, extremes of temperature, abuse etc. is at an easily

accessible height and such that the indicators are at eye level.

Typical locations for the panel are the first and most obvious point of contact for emergency services

or a security office that is likely to be permanently staffed.

2.1.1 Enclosure Details

The LCDA can be surface or semi-flush mounted, is supplied with a detachable front door,

mountable back box and a minimum of two separate PCBs.

2.1.2 Fixing the Chassis to the Wall

Taking into account the weight of the panel securely mount it by using the three keyhole mounting

holes in the backpan, two in the top and one in the bottom. Use suitably sized screws and plugs for

the type of mounting surface.

Caution: Any dust or swarf created during the fixing process must be kept out of the cabinet and

great care should be taken not to damage any wiring or components.

Europe SmartTerminal Installation Commissioning & Operation

Page 6

2.1.3 Board Removal / Replacement

If a PCB has to be removed the following precautions should be observed;

Removing the door will provide better access to the boards and will ensure the hinges are

not accidentally stressed.

Personal anti- static procedures must be followed.

When disconnecting the RJ45 style connecting cable from the PCB, make sure that the

cable remains connected to at least one board to prevent it being misplaced.

Push Tab Inwards

and Gently Pull

the Connector

From the Socket

Connector

Note: Care should be taken when detaching this connector as it is necessary to depress the

small locking tab to unlock the connector from its base. To reconnect the cable the connector must

first be correctly aligned then pushed into the socket so it locks into position.

Carefully remove the retaining screws at each corner of the board taking care not to damage

any of the components.

Place each board into anti- static storage once removed.

Europe SmartTerminal Installation Commissioning & Operation

Page 7

2.1.4 Removing the Knockouts

The knock-outs should be removed with a sharp tap in the rim of the knock-out using a flat broad-

bladed screwdriver. Note: Use of excessive force could damage the enclosure around the knock-out.

Note: BX05 shown the BX1 is set out in a similar manner.

Note: Any unused knock-outs must be securely blanked off.

TO REMOVE THE FRONT DOOR

SLIDE THE TOP AND BOTTOM

HINGE PINS OUT OF THE HINGES

TAP AROUND

RIM TO

REMOVE

KNOCKOUTS

FRONT DOOR

KEY SUPPLIED

TAPED TO TOP

OF ENCLOSURE

ENABLE / DISABLE KEY

SUPPLIED TAPED TO INSIDE

OF ENCLOSURE

CONTROL

PANEL CLIPS

INTO FRONT DOOR

INSERT KEY

TABS HERE

TO UNLOCK

ENCLOSURE

CONNECT BRD82LTB

CN1 TO BRD82ICC

CN5

BRD82ICC

BRD82LTB

HINGE PIN 1

HINGE PIN 2

Figure 2: Exploded View

BRD82LTB

KNOCKOUTS

CN1

R 6mm.

12 mm

KEY HOLE

MOUNTING

HOLE

POWER OUT

POWER IN

+24V

RS485 IN RS485 OUT

03/05/2006

BRD82LTB2-

TB2 TB1 TB4

TB3

LK1

COM

+24V

195mm

39 mm

324mm

213mm

127mm

304mm

175mm

Figure 3: Typical Layout (Externally Powered) and Location of Keyholes

Europe SmartTerminal Installation Commissioning & Operation

Page 8

3 Installation & Cabling

The SmartTerminal is then connected to the FACP as shown below.

TERMINATION BOARD No.1 ( BRD82LTB2 )

SmartTerminal 1

SmartTerminal 2

(IF FITTED)

SHIELDED COMMS CABLE

TO NEXT LCDA

MAXIMUM OF 30

LK1 MUST BE FITTED TO

THE LAST BOARD ON

THE COMMS BUS

+24VDC

TERMINATION BOARD No.2 ( BRD82LTB2 )

LCD

CN1

POWER OUT

POWER IN

+24V

RS485

OUT

03/05/2006

BRD82LTB2-

TB2 TB1 TB4

TB3

LK1 NOT FITTED

COM

+COM

+24V

CN1

POWER OUT

POWER IN

+24V

RS485 IN RS485 OUT

03/05/20 06

BRD82LTB2-

TB2 TB1 TB4

TB3

COM

+24V

VDC

OUT

USB

AUX OUT1

OUT2

OUT1

+VE

COMMS

SGD

+VE +VEA+

0V+27V

INPUTS MONITOR ED O/PSLOOP 1 LOOP 2

B-

RS485+ RS485- SHD

2+ 3+ 4+COM 1+ 2+

AUX OUT2

2- 3- 4-3+1+ 4+1-

ETH

+27V 0V

DIAGNOSTICS RS232

RS485

TERM

LOAD

RESET

HLI

PORT

PWR IN

N/O CN/C N/O CN/C N/O CN/C

REL AY 1 RELAY 2 RELAY3

COMMS

A- B+ B+A- B-A+

JTAG

SEL

DIAGNOSTICS

CN11

TB1 U2U1 U4U3 TB6

R47

CN1

D1 D2

CN10

CN2

CN8

TB4

TB2 TB5TB3

SW1

R38

R4 R5 R6 R7

10K

10K 10K 10K 10K 10K

CONTROLS

SHIELD

MAIN CONTROL BOARD

Figure 4: Connecting SmartTerminal to the FACP

3.1 SmartTerminal Termination Board Interconnection

Terminal Block

TB1 (RS485 OUT) TB2 (RS485 IN) Purpose

1 (Pin Number) RS485 +ve

2 RS485 -ve

3 SCREEN

Terminal Block

TB4 (27VDC OUT) TB3 (27VDC IN)

1 (Pin Number) 0V

2 +24VDC

3.2 FACP Comms

Terminal Block

TB1 (RS 485 OUT) Purpose

1 (Pin Number) RS485 +ve

2 RS485 -ve

3 SCREEN

Terminal Block

TB4 (27VDC OUT)Number Purpose

1 0V

2 +24VDC

Europe SmartTerminal Installation Commissioning & Operation

Page 9

4 Setting the Address

Zone 29-32 Zone 25-28 Zone 21-24 Zone 17-20 Zone 13-16 Zone 9-12 Zone 5-8 Zone 1-4

22/09/2009

BRD82ZICC4-

DIAGNOSTIC /

CONFIG LED

CONFIG

RESET

PRINTER

KEYSWITCH

PWR LINK PWR LINK

FAULT BUZZER

SERIALPARALLEL

COMMS

BUZZER

SILENCE

LCD CONNECTOR

LCD BL

JTAG

FRONT PANEL

INTERFACE

R36

R35

R34

R33

ZDN1

ZD2

ZD1

R32

R31

R30

N1236

D44

D41

D45

TH1

RN7

RN8

U15 RN16 U16

R16

U10 C21

RN2

R10

U11

U13

RN1

RN5

RN4

RN3

RN10

RN20

RN11

RN15

RN12

RN6

R26

R23

R27

R13

R25

R21

R11

R14

R18

R28

LK1

D18

D49

D48

D36

D37

D12

D11

D10

D43 D42 D40

D47

D46

D38

D34

D39

D35

CN10CN9

CN6

CN5

CN4

CN1

CN3

CN2

CN8 CN7

C34

C29

C11

C27

C30

C26

C28

C16

C35

C17

C25

C14

C20

C22

C10

C36

C15

C23

C37

C19

C18

BZ1

R12

C13

C31

C12

R24

RN9

C24

R29

R22

R20

R17

R15

R19

SW28

SW27

C33

C32

D13

D14

D15

D16

D17

D19

D20

D21

D22

D23

D24

D25

D26

D27

D28

D29

D30

D31

D32

RN19

RN14

RN18

RN13

RN17

U14U12

Q10

R37

D33

BRD82ZICC

Main Control PCB

CN2

CN6

LCD

Figure 5: LCD Printed Circuit Board Layout

Open the front door; locate the “CONFIG” button situated on the left hand side of the PCB and press

for 3 seconds. The buzzer and “Config” LED will double beep and flash respectively to indicate that

the Configuration mode has been entered. The LCD will now display the Configuration screen. This

screen consists of the code version number, current address and four adjustment markers. These

markers A-, A+, C-, and C+ are used to indicate the keys that adjust the address and LCD contrast.

Use the “PREVIOUS (A-) and NEXT” (A+) keys to select the desired address. The default value for

this address is 255 which is not a valid SmartTerminal address. The user must then select an

address value from 1 to 30, i.e. the same address as that set in the FACP. The keys corresponding

to C- (ACK) and C+ (RESET) are used in a similar manner to decrease and increase the LCD

contrast level. There is audible feedback for all key presses.

Once the address has been set press the “CONFIG” button again for 3 seconds and the screen will

return to its default and the “DIANOSTIC” LED will return to a slow flash. This slow flash indicates

SmartTerminal and the FACP are communicating normally i.e. the LED flashes if communications

data is being received from the FACP.

Note: If the address is not set within the time out period of approximately 75 seconds

SmartTerminal will return to its normal state.

Europe SmartTerminal Installation Commissioning & Operation

Page 10

5 Setting the SmartTerminal in LoopMaster

This section assumes the engineer has experience in the use of LoopMaster and hence has an

understanding of it operation. To commence the programming go to the “Tree View” within

LoopMaster as shown below.

The Tree View

Figure 6

The above shows the expanded view of the SmartTerminal add on type. In the case above the panel

in question has 1 SmartTerminal assigned to it, entitled ‘Panel Add-on 1’.

Selecting one of these add ons will update the Details Pane with the respective module’s

information, while double-clicking on the add-on will open its editing dialog box.

The SmartTerminal Menu

Right-clicking on the SmartTerminal add on parent item from the Tree View opens the menu,

It contains an option to add a panel Add-on to the panel.

Right-clicking on an existing SmartTerminal add on from the Tree View opens the menu,

It contains an option to add another or remove the current Add-on or via

the ‘Edit Properties’ option to open the Add on editing dialog box.

Note: that it is possible to have a maximum of 30 SmartTerminal add ons per panel, however,

this value will reduce as other add-on types are added (the entire panel can have a maximum of 30

add-ons, of any type, at any one time).

The Details View

Figure 7

The above is displayed as part of the SmartTerminal Details Pane representation of the information

available to the configuration of the data. It is displayed at the top portion of the Details Pane and is

a non-editable, accurate representation of editable fields for a SmartTerminal.

Otros manuales para SmartTerminal

Tabla de contenidos

Manuales populares de Alarma de incendios de otras marcas

Zeta Alarm Systems

Zeta Alarm Systems INFINITY ID2 Manual de usuario

System Sensor

System Sensor 22051TLE-RF-26 Manual de usuario

Pittway

Pittway Notifier AM2020 Manual de usuario

Kidde

Kidde VM-1 Manual del producto

LST

LST SIM016-3 Manual de usuario

Fireboy- Xintex

Fireboy- Xintex FBD-MZ Instrucciones originales

bolid

bolid S2000-IP-03 Manual de usuario

GST

GST DI-9204 Manual de usuario

E2S

E2S BExTBG05D Manual de usuario

Notifier

Notifier UZC-256 Manual de usuario

Fire-Lite Alarms

Fire-Lite Alarms MS-2 Manual de usuario

Siemens

Siemens FDOOT221 Manual de usuario

hyfire

hyfire HY5000 Series Manual de usuario

FlameStop

FlameStop PFSIFP8 Manual de usuario

Radionics

Radionics Radionics 9124 Manual de usuario

UniPOS

UniPOS FD 7120 Manual de usuario

FIREWOLF

FIREWOLF FW-C01224 Manual de usuario

Siemens

Siemens MH-5 Series Manual de servicio