Amina Evolution AIW350E Manual de usuario

Installation Guide AIW350E

Invisible LoudspeakerV1.0 Sept 201 1

Caution: Read before installing this product

To ensure optimal performance, please read

this guide carefully and keep in a safe place

for future reference.

Install this product in a cool, dry, clean place -

away from direct sunlight and heat sources,

vibration, chemical fumes, dust and moisture

(steam).

Do not expose this product to sudden

temperature changes or locate it in an

environment with high humidity. This is to

prevent condensation forming inside which

may cause damage to the product.

Do not clean this product with chemical

solvents as this may damage the finish. Use

a clean, dry or damp cloth.

ENVIRONMENTAL:

Before installing, ensure that the building is environmentally sealed, de-humidified and at a stable

temperature of at least 16 degrees centigrade (61 degrees farenheit)

Please be aware that when this product is directly fitted into a solid wall structure (e.g when using the solid

wall backbox) vibrational energy is inevitably transferred into the solid wall structure. This energy can travel

for some considerable distance up, down and along the structure. It is therefore recommended the

product be fitted within acoustically insulated stud walls or ceiling sections where possible. The use of the

product directly embedded in solid walls is not recommended in multi occupation buildings.

Ensure that all installation mounting surfaces

are able to support the weight of the

product.

After installation, avoid pushing on the wall or

ceiling surface immediately in front of the

speaker. Excessive excursion, whilst unlikely

to damage the speaker, will undoubtedly

crack the plaster around its perimeter.

Do not attempt to modify or repair the

product. Contact your distributor or

manufacturer if a fault should occur.

The rear of the product should not be subject

to chemical cleaning and should not be

painted in any way.

WARNING:

No attempt should be made to install this product within existing building structures unless you are certain

that no electric cables, water pipes, gas pipes or supporting joists will be cut through.

1 0

1 1

1 2

1 3

1 4

1 5

1 6

1 7

1 8

1 9

2 0

2 1

Contents

Message from the Managing Director

Included in the carton / Packaging

How to use this manual

Installation overview diagram

Cavity Installation steps 1 + 2

Cavity Installation steps 3+4

Cavity Installation steps 5 + 6

Cavity Installation with backbox steps 1 + 2

Cavity Installation with backbox steps 3+4

Cavity Installation with backbox step 5

Solid Wall Installation with backbox steps 1 + 2

Solid Wall Installation with backbox steps 3+4

Solid Wall Installation with backbox step 5

Retrofit / plasterboard (patch plastered)

Retrofit / plasterboard (feathered skim)

New Build / plasterboard

Retrofit / solid wall (feathered skim)

Retrofit / solid wall (patch plastered)

New Build / solid wall

Retrofit / drywall (patch plastered)

Retrofit / drywall (feathered skim)

2 2

2 3

2 4

2 5

2 6

2 7

2 8

2 9

3 0

3 1

3 2

Testing the speakers

Plastering and decorating steps 1 + 2

Plastering and decorating steps 3, 4 + 5

Setup tips

Further details

Troubleshooting

Specifications / AIW350E & APU2

Spacesaver information

Warranty & copyright information

Contact information

Section

Preparing the wall / ceiling and

fixing the product

Section

Alignment and plastering preparation

Section

Testing

Section

Finishing

Message from the Managing Director

Congratulations and thank you for purchasing an Amina Technologies AIW350E high performance

invisible loudspeaker.

At Amina we are proud of being at the forefront of flat panel loudspeaker technology. All the

components that make up your AIW350E have been developed specifically to provide the ultimate in

sound quality and reliability, while allowing you to decorate, furnish and enjoy your home in any way

you wish without any visible “clutter” from your audio system.

At the heart of an AIW350E is our high performance vibrational panel driver. Featuring a unique high

power neodymium magnet motor system. This enables the product to provide high quality, high sound

pressure levels from such a compact design. Please take a moment to read this guide which will help

you achieve the best possible performance from your product.

Thanks and enjoy listening.

Richard Newlove

MD - Amina Technologies Ltd

About the manufacturer

Amina Technologies Ltd is the world’s leading designer and manufacturer of truly invisible loudspeaker

solutions. Their invisible loudspeakers have been used in a wide range of both commercial and

residential applications for over twelve years.

Exclusive hotel spas, fashion retail outlets and stunning private residences have all benefited from using

Amina invisible loudspeakers. Amina has the discreet solution ideal for architects, interior designers and

all design conscious clients.

See their website for more details about Amina and a selection of prestigious projects completed using

our products.

Our high power neodymium magnet structures

Included in the carton 02

Model Number

AIW350E

Please check that your carton contains the correct accessories.

Single

1x AIW350E Loudspeaker

1x APU2

1x Spacesaver

Pair

2x AIW350E Loudspeaker

1x APU2

2x Spacesaver

AIW350En 1x AIW350E Loudspeaker

1x Spacesaver

2x AIW350E Loudspeaker

2x Spacesaver

Packaging

The packaging for the AIW350E has been carefully designed to protect the product during transit.

Please retain it in the unlikely event you need to return the product to your dealer or manufacturer.

Please recycle the packaging should you wish to dispose of it.

The AIW350E outer carton is made up of 80% recycled single wall board.

CAUTION:

Take care when removing the speakers from the carton.

How to use this manual

The following pages contain step by step advice to help you achieve a successful installation of your

AIW350E loudspeaker

AIW350E loudspeakers can be installed into walls or ceilings of various construction types. This

installation guide covers the two basic building construction types; plasterboard cavity walls/ceilings

and brick/concrete walls/ceilings. For other construction types please contact Amina.

Cavity wall or ceiling

This is the most common type of installation and requires you to use the Amina BackboxFS (sold

separately) or our basic fixing block kit. Whenever possible we recommend you use the BackboxFS as

the AIW350E has been tuned to work optimally in this setup. The backboxFS also reduces (although

doesn’t entirely stop) the rearward sound output of the AIW350E which is important when considering

the amount of sound transmission that is acceptable through to adjacent rooms/properties.

Solid wall or ceiling

For installation into brickwork or concrete you will need to pre-install an Amina BackboxSW (sold

seperately). When the BackboxSW is installed according to this guide it will position the speaker

correctly and securely in the wall/ceiling, ready to be plastered over.

The details below and the flow chart on the opposite page will allow you to select the correct

installation steps to follow for your particular type of installation.

Section : Preparing the wall / ceiling and fixing the product

In this section, select the type of installation you will be carrying out and begin from the start page

given. This will direct you through the stages, step by step.

Throughout the step by step process, reminders will advise you to view specific pages within Section B.

At this point you will need to ascertain the specific page that best matches your installation

requirement within this section (i.e is it a retrofit installation or a new build?).

Section : Alignment and plastering preparation

Section B is the reference section which is to be used in conjunction with Section A. Please ensure the

correct alignment and plastering method for a retrofit installation or a new build is followed. Reminders

on each page throughout Section A will guide the installer to the correct reference page.

Section : Testing

This section advises you on the correct procedures for speaker testing.

Section : Finishing

This section covers plastering and decorating once your speaker has been installed correctly. It may

again be necessary to refer to Section B in order to apply the correct plastering method.

Installation overview 04

Preparing the wall / ceiling

and fixing the product

Alignment and plastering preparation

Cavity installation Solid installation

Section

Cavity

installation

Typically a new build

or full refurbishment

(wall/ceiling)

Start at page 05

Cavity installation

with backbox

For new builds or full refurbishment

where sound transmission

needs to be reduced

(wall/ceiling)

Start at page 08

Solid structure

installation

with backbox

New builds where the

wall/ceiling has not been

rendered or plastered

Start at page 11

New Build

For new

plasterboard

walls/ceilings

that have

not yet been

plastered

Page 16

Retrofit

patch plastered

For walls/ceilings

that have already

been plastered

Page 14

Retrofit

feathered skim

For walls/ceilings

that have already

been plastered

Page 15

Retrofit drywall

patch plastered

For new drywall

walls/ceilings that

will be taped

and joined

Page 20

Retrofit drywall

feathered skim

For new drywall

walls/ceilings that

will be taped

and joined

Page 2 1

Testing

page 22

Section

New Build

For solid

walls/ceilings

that have

been rendered

but not

yet plastered

Page 19

Retrofit

patch plastered

For solid

walls/ceilings

that have

already

been plastered

Page 18

Retrofit

feathered skim

For solid

walls/ceilings

that have

already

been plastered

Page 17

Finishing

page 23

Cavity installation

Locate joist work

When you have chosen your speaker

locations, before cutting a hole in the

plasterboard it is important that you locate

the position of the wall studs. Ensure the

spacing between them is at least 350mm

(133/4”) for a portrait orientated speaker.

Create 455 x 350mm aperture

Using a sharp knife or pad saw, cut an

aperture with dimensions 455mm x 350mm

(18” x 14”) in your plasterboard wall or ceiling.

Ensure aperture is created between

supporting joists or stud work.

We strongly advise that joists are not cut to

make space for the backbox. Any activity of

this sort may well influence the structural

integrity of your property.

Important: Double check the size of the

aperture is 455mm x 350mm (18” x 14”) as

this is important further on into the

installation process.

Typically a new build or full refurbishment.

Uses fixing blocks (sold seperately)

Reference pages for correct retrofit alignment and plastering method: 14 + 15

Reference page for correct new build alignment and plastering method: 16

Reference pages for correct drywall alignment and plastering method: 20 + 2 1

sharp knife

pad saw

350mm

(minimum)

cut a small

hole in plasterboard

to check stud location

Preparing the wall/ceiling and fixing the product

SPACESAVER:

The supplied Spacesaver may be used to

show the position of the speaker pre-install

by securing it to the wall.

Secure the speaker cable to the Spacesaver

before any building electrical inspection.

See page 30 for full details.

Cavity installation continued... 06

Install speaker cable and insert insulation

Ensure all speaker cables are pulled through

to the speaker location with plenty of slack.

This will make it easier to connect the cable

to the speaker later on in the installation

process.

It is recommended to add sound absorbing

mineral wool inside the cavity to reduce

sound transmission behind the speaker and

limit cavity resonances.

Attach fixing blocks (x4 per speaker)

Position a fixing block under the plasterboard

at each corner of the aperture. Fasten the

thicker section of the fixing blocks to the

underside of the plasterboard using two

drywall screws secured through the front

face of the plasterboard.

NB: ensure there is no gap between the fixing

block and the sawn edge of the plasterboard

aperture.

Important: The fixing blocks are designed for

12.5mm (1/2”) plasterboard (1/2” and 5/8” in

North American markets).

Please contact your supplier if you require

fixings for an alternative plasterboard

thickness.

drywall screws

Reference pages for correct retrofit alignment and plastering method: 14 + 15

Reference page for correct new build alignment and plastering method: 16

Reference pages for correct drywall alignment and plastering method: 20 + 2 1

Top View

Plasterboard

Stud

Fixing block

Cavity installation continued...

Connect the AIW350E speaker

Connect the speaker cable to the speaker

using a high quality crimping tool.

Your AIW350E speaker is fitted with blue butt

splice crimp connectors which are suitable

for speaker cable thicknesses of 1.5mm2-

2.5mm2(16 - 14AWG). This type of connector

ensures a permanent connection is created

inside your wall cavity.

Secure the speaker to the fixing blocks

Important: Ensure there is an all around gap

of 2mm between the speaker and the

plasterboard. If necessary, increase the

aperture size before mounting the speaker.

Using drywall screws, fix the four corner

points of the speaker to the fixing blocks. Pilot

holes are not necessary as drywall screws will

easily self tap into the fixing block.

Ensure the front face of the speaker rests in a

position flush with the front of the

plasterboard and that it is firmly held in

position.

Continue on to Section C (page 22 - testing)

2mm

Reference pages for correct retrofit alignment and plastering method: 14 + 15

Reference page for correct new build alignment and plastering method: 16

Reference pages for correct drywall alignment and plastering method: 20 + 2 1

screw through

here

Tabla de contenidos

Otros manuales de Oradores de Amina

Amina

Amina AIW1X Manual de usuario

Amina

Amina ACPT554E Manual

Amina

Amina Evolution AIW150E Manual de usuario

Amina

Amina MobiusiB Manual de usuario

Amina

Amina Life-Fidelity LFi2T Manual

Amina

Amina APU-RS8iC Manual de usuario

Amina

Amina AIW150i Manual de usuario

Amina

Amina MOBIUS 7 Manual de usuario

Amina

Amina iQ1 Manual de usuario

Amina

Amina AIW750i Manual de usuario

Amina

Amina MOBIUS 7 Manual de usuario

Amina

Amina AIW1X Manual

Amina

Amina AIWX Wood Manual de usuario

Amina

Amina EdgeiBSS-EN54 Series Manual de usuario

Amina

Amina AIW750E Manual de usuario

Amina

Amina Evolution AIW150E Manual de usuario

Amina

Amina AIW2X Manual de usuario

Amina

Amina BackboxSW 345 Manual de usuario

Manuales populares de Oradores de otras marcas

argon audio

argon audio IE20 Manual de usuario

Denon

Denon SC-N7 Manual de usuario

Gemline

Gemline Ace 3952 Manual de usuario

Focal

Focal ON WALL 300 Manual de instrucciones

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manual de usuario

SoundLogic

SoundLogic BCCS-6/6395 Manual de usuario

Peavey

Peavey DTH 218 Manual de usuario

Avantree

Avantree Pluto Air Manual de usuario

Morel

Morel Integra Series INTEGRA OVATION 4 Manual de usuario

Oppo

Oppo SONICA Manual de usuario

Bose

Bose SoundLink Wireless Music System Manual de usuario

Rocksteady

Rocksteady Stadium Manual de usuario

Bowers & Wilkins

Bowers & Wilkins 4 Manual de usuario

Sonance

Sonance SONOS OUTDOOR Series Manual de usuario

Electro-Voice

Electro-Voice EVID FM4.2 Manual de usuario

Pioneer

Pioneer XW-HTD630 Manual de usuario

Onn

Onn BWA16AA002 Manual de usuario

HP GL313AA - USB Speakers PC Multimedia Manual de usuario