American Dryer Corp. SL75 Manual

Service Procedures

for the

Model SL31,50,75 Dryer

Hot Surface Ignitor Gas

Part No. 450279-2

American Dryer Corporation

88 Currant Road

Fall River MA 02720-4781 USA

Telephone: (508) 678-9000 / Fax: (508) 678-9447

e-mail: techsupport@amdry.com

www.amdry.com

“IMPORTANT NOTE TO PURCHASER”

Information must be obtained from your local gas supplier on the

instructions to be followed if the user smells gas. These instructions

must be posted in a prominent location near the dryer.

We have tried to make this manual as complete as possible and hope you will find it useful. The manufacturer

reserves the right to make changes from time to time, without notice or obligation, in prices, specifications,

colors, and material, and to change or discontinue models. The illustrations included in this manual may not

depict your particular dryer exactly.

IMPORTANT

For your convenience, log the following information:

DATE OF PURCHASE ______________________________________________ MODEL NO. ____________________________

DISTRIBUTOR’S NAME ___________________________________________________________________________________

SERIAL NUMBER(S) ______________________________________________________________________________________

_______________________________________________________________________________________________________

For replacement parts, contact the distributor from which the dryer was purchased or contact:

American Dryer Corporation

88 Currant Road

Fall River MA 02720-4781 USA

Telephone: (508) 678-9000 / Fax: (508) 678-9447

e-mail: techsupport@amdry.com

www.amdry.com

Retain This Manual in a Safe Place for Future Reference

This product embodies advanced concepts in engineering, design, and safety. If this product is properly

maintained, it will provide many years of safe, efficient, and trouble free operation.

Only qualified technicians should service this equipment.

OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation

manual included with the dryer.

The following “FOR YOUR SAFETY” caution must be posted near the dryer in a prominent location.

SL31,50,75

FOR YOUR SAFETY

Do not store or use gasoline

or other flammable vapors

and liquids in the vicinity of

this or any other appliance.

POUR VOTRE SÉCURITÉ

Ne pas entreposer ni utiliser d’essence

ni d’autres vapeurs ou liquides

inflammables à proximité de cet

appareil ou de tout autre appareil.

Table of Contents

Part Locations and Removal ................ 4

Lower Front Panel Removal ......................................... 4

Upper Front Panel Removal ......................................... 4

Top Cover Removal ....................................................... 4

Lint Box/Blower Assembly Removal ............................. 4

Gas Valve/Ignition System Removal ............................. 5

Gas Valve/Ignition System Components ...................... 6

Oven Housing Components .......................................... 6

Tumbler Support

Wheel Assembly Replacement .................................... 6

Tumbler Alignment ....................................................... 7

Belt Replacement ........................................................ 8

Placing the Belt ........................................................... 8

SL31Belt Replacement ................................................ 9

Placing the Belt ........................................................... 9

Electrical Component Locations........10

Electrical Panel ......................................................... 10

Sail Switch and Axial Probe Assembly ...................... 10

Exhaust Probe, Exhaust Hi-limit,

and Lint Drawer Switch ............................................... 11

IMPORTANT

You must disconnect and lockout the electric

supply and the gas supply or the steam supply

before any covers or guards are removed from

the machine to allow access for cleaning,

adjusting, installation, or testing of any equipment

per OSHA (Occupational Safety and Health

Administration) standards.

Please observe all safety precautions

displayed on the equipment and/or specified in

the installation manual included with the dryer.

CAUTION

Dryer(s) should never be left unattended while in

operation.

“Caution: Label all wires prior to disconnection

when servicing controls. Wiring errors can cause

improper operation.”

«Attention: Lor des opérations d’entretien des

commandes étiqueter tous fils avant de les

déconnecter. Toute erreur de câblage peut étre

une source de danger et de panne.»

WARNING

Children should not be allowed to play on or near

the dryer(s). Children should be supervised if near

dryer(s) in operation.

Under no circumstances should the dryer door

switch(es), lint door/drawer switch(es), or heat

safety circuit(s) ever be disabled.

The dryer must never be operated with any of the

back guards, outer tops, or service panels

removed. Personal injury or fire could result.

The dryer must never be operated without the lint

filter/screen in place, even if an external lint

collection system is used.

FOR YOUR SAFETY

Do not use dryer in the presence of dry

cleaning fumes.

The dryers must not be installed or stored in

an area where it will be exposed to water

and/or weather.

The wiring diagram for the dryer is located in

the front electrical control box area.

4 American Dryer Corporation 450279-2

Part Locations and Removal

LOWER FRONT PANEL REMOVAL:

Remove the lint drawer. Remove the four screws

located just below the loading door. Tilt the top of

the panel out and lift the panel up and away from the

dryer.

Unplug two connections on the exhaust hi-limit at

the left of the lint box. Also disconnect the two

connections for the lint drawer switch, located at the

back of the lint box. The lint box may now be pulled

out through the front of the dryer.

Unplug the motor harness.

For SL31, remove two screws above the lint drawer.

For SL50,75, also remove two screws beneath the

gasket on the left and right side of the lint drawer.

Also, unplug the exhaust temperature probe.

LINT BOX/BLOWER ASSEMBLY REMOVAL:

TOP COVER REMOVAL:

First remove the back guard, the four screws holding

top cover. Next pull top cover toward the rear of the

dryer and lift up.

Tilt the bottom of the panel out and lift the panel up.

Align support rod into hole to support control panel.

Disconnect the electrical connections. Remove

screw from hinge to remove the control panel.

LINT DRAWER

SWITCH

EXHAUST

HI-LIMIT

For Models SL31,50,75

SUPPORT

ROD

DOOR

SWITCH

UPPER FRONT PANEL REMOVAL:

Remove the four screws located just above the top

loading door. Tilt the bottom of the panel out and lift

the panel up and away from the dryer.

For Models SL31,50,75

450279- 2 www.amdry.com 5

GAS VALVE/IGNITION SYSTEM REMOVAL:

Be sure to shut off the gas main and then proceed

to remove electrical connections and screws

indicated. Remove lower front panel. Disconnect

union and screws noted with arrows.

By removing the top screws you will be able to

remove the burner tube. After, removing the top

burner, without damaging the Hot Surface Ignitor,

remove the whole gas valve assembly. Be careful

during assembly not to damage the Hot Surface

Ignitor. Replace assembly in the reverse order.

Inspect all wires to be sure all lead directly toward

the front of the dryer. Be sure no wires are caught

on the burner tube or ignitor.

To remove motorized impellor assembly:

Remove the six hex nuts shown with arrows. Now

pull the blower motor assembly apart from the blower

housing. Remove the four Phillips screws shown

with arrows and separate the motorized impellor

from the blower motor mount.

To remove motorized impellor assembly, remove lint

housing cover, lint screen, and the four screws

shown with arrows. Pull the motorized impellor

assembly out through the opening.

For Models SL31,50,75

Gas Valve Ingnition System

6 American Dryer Corporation 450279-2

OVEN HOUSING COMPONENTS:

GAS VALVE/IGNITION SYSTEM COMPONENTS:

BURNER TUBE

IGNITOR

GAS VALVE

For Models SL31,50,75

OVEN CHAMBER

RADIANT

SENSORS

HOT SURFACE

IGNITOR

Dual Burner SL50,75

RADIANT SENSOR

BURNER HIGH-LIMIT

GAS VALVE

HOT SURFACE

IGNITOR

TUMBLER SUPPORT

WHEEL ASSEMBLY REPLACEMENT:

The front wheel assemblies can be replaced with

the lower front panel removed. Remove the three

bolts by reaching upward with a socket or box

wrench. The illustration below is provided to show

the location of these wheels as the wheels cannot

easily be seen while standing in front of the dryer.

All wheel assemblies are mounted on slots to allow

for alignment of the tumbler. After one or more wheel

assemblies are replaced, the tumbler must be

realigned.

The left rear wheel assembly can be removed with

just the back guard removed. The rear right wheel

requires removing the back guard, heat duct, and

oven. Be sure to mark the position of rear wheel

brackets prior to removal (refer to photo right).

For Models SL50,75

For Models SL31

450279- 2 www.amdry.com 7

Adjust the tumbler position by loosening the three

bolts and forcing the wheel assembly toward the

center of the dryer to raise the tumbler and to move

it away from the side. A large screwdriver can

provide the necessary leverage. Adjustment of the

front of the tumbler is made by equalizing the gap

on the top, bottom, left and right by moving the wheel

assemblies.

TUMBLER ALIGNMENT:

Proper alignment is achieved by making the gap

between the tumbler and openings in the front and

rear bulkheads equal on all sides.

The front to bulkhead may be checked for accuracy

by using a thickness gauge. The rear gap is not

accessible. Marking the position of the rear wheel

brackets before removing the brackets will help in

replacing the tumbler back into it’s original position

when the wheel brackets are reinstalled.

Below, both wheel assemblies are adjusted correct

and spacing is even on all sides.

EXAMPLES:

In the illustrations to the right, both wheel assemblies

must be moved to the right in order to move the

tumbler right. The left wheel assembly must move

a little more than the right in order to lift the tumbler.

8 American Dryer Corporation 450279-2

BELT REPLACEMENT:

Shut off electrical power to the dryer. Lockout and

tag out supply voltages. Follow the steps to remove

front middle panel. Next you will remove either the

front bottom or front upper panel, depending on

pocket you are working on. Remove the belt from

the motor sheave. Next, remove the two screws

fastening the lint coupe to the front panel. Remove

the front panel screws, while holding up the

basket. Tilt the top of the front panel forward. Take

note of position of motor adjustment nut. Spin

counterclockwise to loosen tension. The old belt

can now be removed. Slide the new belt around

basket and push belt to a position close the motor

sheave.

PLACING THE BELT:

Now that the belt is close to the motor sheave (Fig.1),

make sure the motor pivot is at it’s highest point.

Wrap the belt under the motor sheave (Fig.2), then

push the belt over the idler wheel (Fig.3). Once this

has been accomplished make sure to spin the

basket by hand to self align the belt on motor sheave

and idler wheel. Tighten the motor adjustment nut

to position previous set.

FIG. 1

FIG. 2

FIG. 3

450279- 2 www.amdry.com 9

SL31 BELT REPLACEMENT:

Shut off electrical power to the dryer. Lockout and

tag out supply voltages. Follow the steps to remove

front middle panel. Next you will remove either the

front bottom or front upper panel, depending on

pocket you are working on. Remove the belt from

the motor sheave. Next, remove the two screws

fastening the lint coupe to the front panel. Remove

the front panel screws, while holding up the

basket. Tilt the top of the front panel forward. Take

note of position of motor adjustment nut spin

counterclockwise to loosen tension. The old belt

can now be removed. Slide the new belt around

basket and push belt to a position close the motor

sheave.

PLACING THE BELT

BACK ON THE MOTOR SHEAVE:

Place belt installation tool (BIT-P/N 320650) over belt

(Fig. 1) and rotate in a clockwise direction. While

rotating run BIT under motor sheave (Fig. 2).

Continue to spin BIT, belt will then wrap under motor

sheave (Fig. 3). Remove BIT from dryer (Fig. 4).

Next, you want to rotate basket slowly to ensure it is

on the sheave completely. Tighten the motor

adjustment nut to position previous set.

FIG. 1

FIG. 4

FIG. 2

FIG. 3

10 American Dryer Corporation 450279-2

Electrical Component Locations

SAIL SWITCH AND AXIAL PROBE ASSEMBLY:

Located behind back guard. Access doors are

provided. Back guard does not have to be removed.

ELECTRICAL PANEL:

The electrical panel is located behind the front middle

panel.

For Models SL31

For Models SL50,75

DOOR

SWITCH

COMPUTER

PANEL

COVER

ROTATIONAL

SENSOR

SWITCH

REVERSING

RELAY

COMPUTER

COVER

DOOR SWITCH

For Models SL50,75

For Models SL31

AXIAL

PROBE

SAIL

SWITCH

BURNER

HIGH LIMIT

AXIAL

PROBE

SAIL

SWITCH

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Secadora de American Dryer Corp.

American Dryer Corp.

American Dryer Corp. Phase 5 Microprocessor AD-170 Manual de usuario

American Dryer Corp.

American Dryer Corp. PHASE 7 OPL Manual de usuario

American Dryer Corp.

American Dryer Corp. ML-190 Manual de usuario

American Dryer Corp.

American Dryer Corp. ML-122D Manual de usuario

American Dryer Corp.

American Dryer Corp. AD-115ES II Manual de usuario

American Dryer Corp.

American Dryer Corp. Gas/Electric/Steam ML-55HS Manual de usuario

American Dryer Corp.

American Dryer Corp. MLG-130DR (HSI) Manual de usuario

American Dryer Corp.

American Dryer Corp. ADE-50S Manual de usuario

American Dryer Corp.

American Dryer Corp. Dyer AD-26 Manual de usuario

American Dryer Corp.

American Dryer Corp. Wet Wash ML-79 Guía del administrador

American Dryer Corp.

American Dryer Corp. Hot Surface Ignition System ADG-530 Manual de usuario

American Dryer Corp.

American Dryer Corp. AD-30 (Export) Guía del administrador

American Dryer Corp.

American Dryer Corp. EURO-24 Guía del administrador

American Dryer Corp.

American Dryer Corp. AD-100 Manual de usuario

American Dryer Corp.

American Dryer Corp. HB76 Manual de usuario

American Dryer Corp.

American Dryer Corp. Aquatex AD-76 Manual de usuario

American Dryer Corp.

American Dryer Corp. AD-15 thru AD-75 Manual de usuario

American Dryer Corp.

American Dryer Corp. AD-400 Manual de usuario

American Dryer Corp.

American Dryer Corp. AD-60 Manual de usuario

American Dryer Corp.

American Dryer Corp. Gas DSI/HSI/Electric/Steam/Phase 7 with S.A.F.E.... Manual de usuario

American Dryer Corp.

American Dryer Corp. CE 96-190 Manual de usuario

American Dryer Corp.

American Dryer Corp. AD-385 Guía del administrador

American Dryer Corp.

American Dryer Corp. ADG-531HS Manual de usuario

American Dryer Corp.

American Dryer Corp. AD-100 Manual de usuario

Manuales populares de Secadora de otras marcas

Bosch

Bosch WTA79200GB Manual de usuario

Amana

Amana W10233410A Manual de usuario

Miele

Miele TWH 780 WP Manual de usuario

Asko

Asko T760 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Manual de usuario

Bosch

Bosch Logixx 10 WTB76556GB Hoja de especificaciones

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Manual de instrucciones

Electrolux

Electrolux EW2H328R2 Manual de usuario

Beko

Beko DS8433RX1M Manual de usuario

Dawlance

Dawlance Spinner DS 6000 C Manual de usuario

Electrolux

Electrolux TP5080TW Manual de usuario

AEG

AEG TR838P4OB Manual de usuario

Indesit

Indesit IDV 75 Manual de usuario

Infiniton

Infiniton SD-DG85C Manual de usuario

BOMANN

BOMANN WT 5019 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Manual de usuario

Asko

Asko T793C Manual de usuario

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manual de usuario