AMC VOX-4W Guía del usuario

www.amcelettronica.com VOX-4W v. 1.0

VOX-4W

TWO-WAY GSM DIALER WITH ENVIRONMENTAL LISTENING

INSTALLER'S

MANUAL

ENGLISH

DESCRIPTION

Voxout is a two-way integrated dialer with keyboard, equipped with environmental listening and a simulated telephone line.

Its main features are:

. provider test/best gsm signal based on available cells

- credit exhaustion management, with voice alert and/or sms for low credit threshold (programmable threshold)

- sim expiration display (for operators who support the sms service)

- remote control with voice guidance

- local programming from keyboard

- remote programming via sms

- output enabling via ring with confirmation ring

- 5 selectable lines that can be freely programmed as inputs or outputs

- Double State Signal: vocal calls / sms on opening/restoring of the inputs

- 1 local input for reset of calls in progress

- 1 simulated PSTN line with which it is possible to make phonecalls with a standard touch-tone telephone, or connect the dialer to

a wire telephone exchange.

- 12 user codes

- 8 programmable telephone numbers for voice calls and SMS

- 8 programmable telephone numbers for digital transmission of contact ID

- 200 programmable telephone numbers for the remote control function

www.amcelettronica.com VOX-4W v. 1.0

- WALL MOUNT AND CABLING -

The wall mount should be performed using the holes on the rear of the cover (1)

cable routing

fixing holes

knock-out protection

tear

www.amcelettronica.com VOX-4W v. 1.0

- TECHNICAL INDICATIONS OF USING -

IMPORTANT: the equipment, if used like a device for transmission of alarms of a CIE, can be connected only

if:

- the CIE complies to EN 50131-1 and EN 50131-3 (Grade 1)

- the terminals “1,2”, connected to the outputs of a CIE, are programmed as “balanced inputs”, and confi-

gured to send vocal calls/SMS for intrusion and power failure;

- the terminal “3” is configured like “output of type T” (tamper) and connected to an input always active

controlled from the CIE;

- the terminal “4” is configured like “output of type G” (GSM failure) and connected to an input controlled

form the CIE;

- the terminal “5” can be used with a CIE that has the function of “robbery” (in this case the terminal con-

nected to an output of a CIE, must be progammed like “balanced input” and configured to send vocal calls/

SMS for robbery) or with a CIE that allows access at level 3 without the authorization of users at level 2.

NOTE: for CIE with grade upper to 1 and/or when there are 2 or more inputs like robbery, the device of tran-

smission of alarms can not be used (availability in inputs/outputs insufficient).

- INDEX -

PROGRAMMING MENU FROM KEYBOARD - 1 page 03

PROGRAMMING MENU FROM KEYBOARD - 2 page 04

PROGRAMMING MENU FROM KEYBOARD - 3 page 05

USER MENU page 06

VOICE GUIDED MENU page 07

CARD DESCRIPTION - EXAMPLE OF A CONNECTION TO AN EXCHANGE page 08

BEST PROVIDER TEST page 09

SYMBOLS AND DISPLAY VIEWING IN STANDBY page 09

RESET DEFAULT page 10

LED FUNCTIONING LOGIC page 10

PROGRAMMING page 10

MENU OF IN / OUT LINES NAMES page 10

MENU OF IN / OUT LINES TYPE page 10

MENU OF TELEPHONE NUMBERS page 11

RESET OF CALLS / SMS page 11

MENU OF VOICE CALLS page 11

MENU OF SMS MESSAGES page 12

MENU OF INPUTS page 13

MENU OF OUTPUTS page 13

MENU OF USER CODES page 14

SIM CREDIT INFO MENU page 15

TEST MENU page 15

MENU OF VARIOUS PARAMETERS page 16

PROGRAMMING AND MANAGEMENT FROM SMS MESSAGES page 17

TECHNICAL SPECIFICATIONS page 20

www.amcelettronica.com VOX-4W v. 1.0

PROGRAMMING MENU FROM KEYBOARD - 1

PERSONAL

CODE

Cod. TECHNICAL

000000

Cod. USER

111111

E01 opening of Input 1

E02 opening of Input 2

E03 opening of Input 3

E04 opening of Input 4

E05 opening of Input 5

E06 closing of Input 1

E07 closing of Input 2

E08 closing of Input 3

E09 closing of Input 4

E10 closing of Input 5

E11 Tamper of Input 01

E12 Tamper of Input 02

E13 Tamper of Input 03

E14 Tamper of Input 04

E15 Tamper of Input 05

E16 Life Test

E17 GSM OFF 1min

E18 Tampering

E19 Low Credit

TELEPHONE

NUMBER MENU

TEL. NUMBER from [ 01 ] to [ 08 ]

VOICE CALL

E01 –opening L01

V-PLAY X-REC

VOICE MESSAGE

Listen/Record

VOICE MESSAGES

Assign telephones

Answ. Wait 50

Time of Attempts 15

Num. of attempts 3

Msg. repet. 2

SMS MESSAGE

SMS MENU

Edit test SMS L1 opening

Insert text……..

SMS MENU

Assig telephones E01 / tel 12345678

SMS/ tel 12345678

echo

This parameter send all the SMS received by the

dialer to the programmed numbers

Time in sec. of the duration

Of the outgoing calls

CANCEL (x) TO RECORD

ENTER (V) TO LISTEN AGAIN

Time in sec. between one attempt

and the next call attempt

Call attempts made in case

phonecalls have not been

successful

Number of repetitions of the

voice message

EXT NUMBER from [001] to [200]

The phone book with 200 numbers allows the user to enable

output 5, by sending out onlyone ring to the dialer.

IMPORTANT: always type in the phone number with the

international country code (+39 for Italy)

IN/OUT LINES

MENU IN/OUT LINES

NAME

IN/OUT LINES

TYPE

LINE NUM. [01]

LINE 01

OPT/TEL. 01 to 08 ABC

SISTEM NAME

V-PLAY X-REC

E01 / tel 12345678

*- play

INPUTS

Enter (✔) = to change

Rh arrow to change input

Up arrow to choose function

- = not programmed input

A = Alarm with reset input closed

H = input 24h always enabled

Function [ 01 ] Line 01

H----

Associate Outputs Enter (✔) = to change

1- 5 n° associated output

- = output unassociated

Enter (✔) = to change

Rh arrow to change input

Up arrow to choose function

- = not programmed

O = NO

C = NC

B = balanced

U = output

[ 01 ] Line 01

O - - - -

[ 01 ] Line 01

inàOut 2 - - - -

Line 01 Msg

Linea 02 Msg

Linea 03 Msg

Linea 04 Msg

Linea 05 Msg

SYSTEM Name

Event

A = answer confirm with #

B = direct access to vocal menù

C = reset call cycle

www.amcelettronica.com VOX-4W v. 1.0

PROGRAMMING MENU FROM KEYBOARD - 2

This parameter allows the user to enable/disable the

outputs by sending out a ring from a programmed

remote telephone. If the output duration is 0, output is

stable, therefore enable/disable step by step. If other

than 0, it becomes a pulse output.

IMPORTANT: always type in the telephone number

with the international country code (+39 for Italy).

The output must have function P

Enter (✔) = to change

Rh arrow to change output

Up arrow to choose function

- = not programmed

A = Is enabled with input associated with RES

closed low

H = Is enabled with associated input (always, also

with RES open)

T = Tamper alarm

U = Associated to a user code (local and remote)

P = Can be piloted from remote without user code

G = gsm problem (no GSM for 60'’)

I = Input in standby

C = Low credit

R = ring

M = Master (key 6)

1 - 5 = User enabled only to enable/disable the

associated output (the output must have function U)

OUTPUT

MENU Function

Pulse duration

Associate Telephones

USER CODE

MENU User types [ 01 ] User Nr 01

Program Codes

CODE: User Nr xx

111111 (default UT01)

Reset Calls

999999 (default)

SIM Code

0000 (default)

Tel 12345678

Prog ●●●●●●●●

Program with

□

the numbers enabled to the

operations on the dialer.

Warning: to ensure proper operation, the

telephone numbers in the phone book must

always be preceded by +39

Program the desired number for the manual

reset of the call que (it is sufficient to insert even

just one digit).

[ 01 ] Line 01

H - - - -

L1 O / tel 12345678

[ 01 ] Line 01

Sec. 15

www.amcelettronica.com VOX-4W v. 1.0

PROGRAMMING MENU FROM KEYBOARD - 3

SIM CREDIT INFO

Tel. TIM

40916

Tel. VODAFONE

404

Tel. wind

4155

Tel. other

TIM Credit

PRE CRE SIN

VODAFONE Credit

WIND Credit

SALDO

OTHER Credit

Credit threshold

[EURO] 3

VARIOUS

PARAMETERS

Life Test 0

Answ. Ring 3

Event Delay 5

Value expressed in hours

Time in seconds of the inhibition of an

input after a first opening

Board Tamper 0 0 = disabled

1 = enabled

Key Buzzer 0

Accept Calls 1

Pass Ring 0

Language 0

TIM expiration

PRO INFO

Vodafone expiration

WIND expiration

INFO

OTHER expiration

Enable TVWA

SIM expiration

Environment Vol. 8

MENU TEST TEST

Voice call

KEYWORD

ACCESS POINT

Iliad

USER NAME APN

-----

PASSWORD APN

-----

www.amcelettronica.com VOX-4W v. 1.0

USER PROGRAMMING MENU

PERSONAL

CODE

ENABLE OUTPUT

D = Disabled

E = Enabled

- = Disabled (specific function assigned)

CHANGE

PERSONAL CODE

CODE: User No. xx

111111

Cod. USER DEFAULT 111111

[ 01 ] Line 01

D----

Key to enable outputs

Key to disable outputs

Attention !

The functions “Medical Aid” (key “arrow left”) and “Fire” (key “arrow right”) are not covered from the

EN 50136-2-1 and are not used from the dialler.

So the two keys are NOT used for these functions.

www.amcelettronica.com VOX-4W v. 1.0

VOICE GUIDED MENU

voice guided menu

The vocal menu is reachable by calling the dialler or when the dialler calls. It’s not used for programming but only for remote man-

agement by the user.

When receiving a call, during the listening or at the end of the voal message, it’s possible:

Type in personal code

followed by #

Incorrect personal

code

2 to act on the remote

commands

4 to connect to a

remote system

3 to know the inputs

status

Choose 1 to Enable/Disable Out “1”

Choose 1 to Enable/Disable Out “2”….

Choose 1 to Enable/Disable Out “5”

Wait

Input “name” enabled/disabled

System enabled (reset closed)

System disabled (reset open)

Incorrect

Welcome

Choose 1 to enable

the environmental

listening option

Key 1 = raise volume

Key 2 = lower volume

# to return to the menu

Code

Enable RING output. If a

terminal PHONE is connected,

by lifting the receiver

communication is enabled

- STOP THE CYCLE CALL WITH THE RESET CODE: by pressing the #, digit the code reset and confirm con # (es. #123#), the voice

will say “cycle call terminated”

- ENTER IN THE VOCAL MENU:ENTRARE NEL MENU’ VOCALE: by pressing the #, digit the user code and confirm con #. It will

be possible to select one of the four voice of the vocal menu.

www.amcelettronica.com VOX-4W v. 1.0

CARD DESCRIPTION - EXAMPLE OF A CONNECTION TO AN EXCHANGE

Out1= no 220V

Note: in the example shown in the figure, the dialer is powered by fixed charges from the exchange, the free exchange of the alarm

relay is connected to input 1, the OPEN-COLLECTOR 1 output is configured as the absence of an electrical netwrok and is connected

to input 2.

SUPPLY + - = power supply 13.8Vcc

L 1-2-3-4-5 = Lines inputs / outputs -- Configured like Inputs, refer to NEGATIVE -- Configured like outputs, they

give a NEGATIVE when they are activated

RES = reset of the calls in progress (OPEN TO RESET) -- Referred to NEGATIVE --

PHONE = emulation of a wired telephone line

www.amcelettronica.com VOX-4W v. 1.0

SYMBOLS AND DISPLAY VIEWING IN STANDBY

FW:1.00

SIM: 11/12/2012

iTIM

1 4 532

Input icon

Output icon

When flashing, indicates input/outoput not in standby

2Indicates input/output in standby

€ 10.92

By pressing the CANC(X) key, it moves from standby

screen to SIM credit/expiration screen

The value of credit is updated automatically every

time that the dialler makes a call or sends a SMS.

It’s possible to request the credit of the SIM also by

pressing ENTER (✔) from this screen.

Note: in the screen that concerns the credit and the sim’s expiration, if question marks appears instead of the data,

the information is not available at the moment. If “dots” appear instead, the system is updating the information

with the provider.

By pressing the CANC (X) key again, you will shift to the display (if available) of the entire SMS received from the

Provider

NOTE: The availability of residual credit value is closely related to the Provider of the GSM network that can pro-

vide this service or not

BEST PROVIDER TEST

Powering the dialer with an antenna wire inserted and without SIM, an analysis will be made of the signals and of the providers

present on site, and the provider with the best signal will be indicated.

The display altenrates the 2 following screens.

1 4 532

SIM RECOMMENDED

1 4 532

iTIM

Once you’ve defined the provider,remove power supply and insert the SIM in the dialer (the SIM is unlocked with the PIN number).

Power the system again, and wait for the signal and the mobile phone operator to appear on the display, as shown in the example

of the following screen:

Tabla de contenidos

Idiomas:

Otros manuales de Teléfono móvil de AMC

AMC

AMC vision 3 compact Manual de usuario

Manuales populares de Teléfono móvil de otras marcas

Zte

Zte BLADE A520 Manual de usuario

Nokia

Nokia Lumia 620 Manual de usuario

Blackbe;rry

Blackbe;rry KEYone Manual de usuario

Bea-fon

Bea-fon X5 Premium Manual de usuario

Blackbe;rry

Blackbe;rry 8707 Series Manual de usuario

Blackbe;rry

Blackbe;rry Storm Instrucciones de funcionamiento

LG LM-X420QN Manual de usuario

LifeWatch

LifeWatch V Manual de usuario

Bea-fon

Bea-fon SILVER LINE SL860 Manual de usuario

IKI Mobile

IKI Mobile KF4.5i Manual de usuario

Hitech

Hitech HT-850 Manual de usuario

Yezz

Yezz Fashion F10 Manual de usuario

Point Mobile

Point Mobile PM60 Manual de usuario

Blackbe;rry

Blackbe;rry Q10 Manual de usuario

Blackbe;rry

Blackbe;rry Bold 9900 Manual de usuario

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Manual de usuario

LG LM-K420EMW Manual de usuario

ISAFE MOBILE

ISAFE MOBILE IS655.2 Manual de usuario