Amazon B07V3QLZ5Y Manual de usuario

No.4 Bench Hand Plane - 2-Inch Blade

RabotNo4-Lamede2Pouces(5cm)

HandhobelNr.4-2-Zoll(5cm)-Klinge

PiallaaManodaBancoN°4-Lamada2Pollici(5cm)

CepilloCarpinteroparaBancoN.º4-Cuchillade

2Pulgadas(5cm)

BlokschaafNr.4-2Inch(5cm)Mes

No.4ベンチハンドプレーン（かんな）-2インチ（5cm）ブレードRęcznyStrugWarsztatowyNr4—Ostrze2-calowe(5cm)

Nr.4Bänkhyvel-2-tums(5cm)blad

B07V3QLZ5Y

English. . . . . . . . . . . . . . . . . . . . . . . . 3

Français . . . . . . . . . . . . . . . . . . . . . . 13

Deutsch . . . . . . . . . . . . . . . . . . . . . . 24

Italiano . . . . . . . . . . . . . . . . . . . . . . 35

Español . . . . . . . . . . . . . . . . . . . . . . 46

Nederlands . . . . . . . . . . . . . . . . . . . 57

日本語. . . . . . . . . . . . . . . . . . . . . . . 68

Polski. . . . . . . . . . . . . . . . . . . . . . . . 80

Svenska . . . . . . . . . . . . . . . . . . . . . . 90

Table of Contents

1. Important Safeguards �� 4

2. Intended Use �� 5

3. Before First Use �� 5

4. Tool Overview �� 6

5. Assembly/Disassembly �� 7

6. Adjustment �� 7

7. Operation �� 8

7�1 General rules �� 8

7�2 Working techniques �� 9

8. Maintenance �� 9

8�1 De-rusting and rust protection �� 9

8�2 Sharpening the blade �� 10

8�3 Flattening the sole �� 11

8�4 Storage �� 11

9. Specications �� 12

10.Feedback and Help �� 12

1. IMPORTANT SAFEGUARDS

Read these instructions carefully and retain them for

future use� If this tool is passed to a third party, then these

instructions must be included�

When using the tool, basic safety precautions should always be

followed to reduce the risk of injury including the following:

CAUTION Risk of cuts!

»Parts of this tool are are extremely sharp� Care must be taken

at all times when handling them� To avoid injury the tool

should always be held with two hands�

»This tool is not a toy� Children must always be supervised by an

adult when using the tool�

»Remain alert and use good judgment when using this tool� Do

not use this tool if you are in any way impaired by medications,

alcohol, drugs or fatigue�

»Dress appropriately and remove all jewelry, secure loose

clothing and tie up long hair before using this tool�

»There is a risk of splintering and dust formation during

woodworking� Wear appropriate protective clothing (e�g� work

gloves, dust mask, safety glasses, etc�)�

»Keep the blade sharp to avoid the plane catching on material

which may cause it to move in an unexpected way or cause

workpiece damage�

»Always check the workpiece for any metal (nails, screws,

staples, etc�) that could damage the cutting edge�

»Make sure that the workpiece is clamped or held securely�

»Do not modify the tool in any way unless instructed by this

user manual�

2. Intended Use

»This tool is intended for woodworking, mainly for creating even

and plane surfaces�

»This tool is intended for household use only� It is not intended

for commercial use�

»No liability will be accepted for damages resulting from

improper use or non-compliance with these instructions�

3. Before First Use

DANGER Riskofsuocation!

»Keep any packaging materials away from children – these

materials are a potential source of danger, e.g. suocation.

»Check the tool for transport damages�

»Remove all the packing materials�

»Make sure the blade(E) is sharp and the sole(I) is at before

use. Sharpen the blade(E) and atten the sole(I) if necessary

(see section “Sharpening the blade” and “Flattening the sole”)�

4. Tool Overview

ABlade screw GRear handle

BClamping screw HBase

CLever cap ISole

DBlade adjustment slots JFront handle

EBlade KCutting edge

FDepth adjustment wheels

5. Assembly/Disassembly

NOTICE To disassemble the tool, follow the steps below in a

reverse order�

1� Place the blade(E) onto the base(H). The at surface of the

blade has to face upwards. The blade adjustment slots(D) must

t around the depth adjustment wheels(F).

2� Place the lever cap(C) on the blade(E).

3� Tighten the clamping screw(B)�

4� Tighten the blade screw(A)�

NOTICE Do not over-tighten the clamping screw (B)�

It should be tightened enough to secure the blade (E) during

use� Turning the depth adjustment wheel (I) should be possible

without an excessive force�

6. Adjustment

NOTICE

»For creating an even workpiece surface, the blade’s(E)

cutting edge(K) should be parallel to the mouth opening on

the sole (I)�

»If you want to achieve a side slope you can move one side of

the blade(E) out more than the other� In that case the side

protruding more from the mouth opening will cut deeper

into the workpiece surface�

Turn the depth adjustment wheels(F) to adjust the depth of cut�

»Turn the depth adjustment wheels(F) clockwise to move the

blade in for increasing the cutting depth�

»Turn the depth adjustment wheels(F) counter-clockwise to

move the blade out for reducing the cutting depth�

7. Operation

For a secure operation always hold the tool with one hand on the

front handle(J) and the other hand on the rear handle(G)�

7.1 General rules

For best results:

»Move the blade(E) downwards.

7.2 Working techniques

1� Hold the tool with both hands. Put the palm of one hand

on the top of the front handle(J), and rmly grab the rear

handle(G) with the other hand.

2� Place the tool with it’s sole(I) on the workpiece. Push and pull

along the surface of the workpiece with the rear handle(G),

while pressing down hard on the front handle(J).

8. Maintenance

8.1 De-rusting and rust protection

»Use commercially available rust cleaner or citrus cleaner� Wear

gloves and follow manufacturer’s cleaning instructions�

»Spray the metal components� Let them stand for several

minutes then, using steel wool, brass brush or toothbrush,

scrub o as much of the rust as you can.

»To prevent the metal parts from rusting, keep them lubricated

with a commercially available lubrication solution�

NOTICE Some lubrication solutions may interact with the

wood what may aect the look of the wood. Ask your dealer for

an accurate lubrication solution�

8.2 Sharpening the blade

Use quality oil sharpening stones� Lubricate them with an accurate

lubrication solution�

1� Remove the blade(E) from the tool�

25° 30°

2� Place the cutting edge (K) against the sharpening stone at

approximately 25° angle�

3� Slightly lift the blade (E) to a 30° angle.

4� Pull the blade(E) backwards to sharpen the cutting edge(K)�

Repeat until sharpened�

5� Draw the sharpened cutting edge (K) across the corner of a

scrap piece of wood to remove burr�

6� Reassemble the tool�

Tabla de contenidos

Idiomas:

Otros manuales de Accesorios para videojuegos de Amazon

Amazon

Amazon HDML-Cloner Box Manual de usuario

Manuales populares de Accesorios para videojuegos de otras marcas

VENOM

VENOM VS3057 Manual de usuario

LINK-MI

LINK-MI HDVC01 Manual de usuario

Thrustmaster

Thrustmaster T60 Manual de usuario

Avermedia

Avermedia C875 Manual de usuario

VENOM

VENOM VS2728 Manual de usuario

DGT

DGT 960 Manual de usuario

Sega

Sega Visual Memory Unit Manual de usuario

Datel

Datel Go-tcha Expedition Manual de usuario

TruGolf

TruGolf TruFlight 2 Manual de usuario

CH Products

CH Products CH PRO THROTTLE Manual de usuario

Thrustmaster

Thrustmaster T2PA Manual de usuario

Cube Controls

Cube Controls Mercedes-AMG - GT Edition SIM Wheel Manual de usuario

Hoffmann

Hoffmann Club Pro Manual de usuario

ardistel

ardistel ADT SpeedRacer Manual de usuario

Sven

Sven GC-W150 Manual de usuario

Deltaco Gaming

Deltaco Gaming GAM-131 Manual de usuario

Huffy

Huffy M731324 Manual de usuario

Ace Bayou

Ace Bayou X Rocker Manual de usuario