Amazon B07SZVW98Z Manual de usuario
Drive Click Torque Wrench
Clé Dynamométrique à Cliquet
Drehmomentschlüssel
Chiave Dinamometrica a Scatto ad Avvitamento
Llave Dinamométrica Drive de Disparo
Drive Klik-Draaimomentsleutel
ドライブクリックトルクレンチ
B07SZVW98Z, B07SYTQ6FT, B07SV45HRY, B07ST25HJ5
English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Nederlands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
日本語 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3
EN
IMPORTANT SAFETY
INSTRUCTIONS
Read these instructions carefully and retain them for future use.
If this product is passed to a third party, then these instructions
must be included.
When using the product, basic safety precautions should always be
followed to reduce the risk of injury including the following:
• Do not use the product to loosen bolts, screws or the like, as this
might damage the ratchet and the calibrated settings.
• Do not use brute force on the product to tighten a nut/screw. During
tightening apply a steady and consistent pressure. Do not use as a
nut breaker, pry bar, hammer, or lever bar.
• To prevent damage to the product, stop applying pressure when
the “click” sound is heard. Bear in mind that the “click” sound is
acoustically weaker with lower torque settings.
• The product should be re-calibrated when it has been subjected to
an overload greater than its rated capacity, after repair, or after any
improper handling which might influence the errors of measurement.
• Do not use worn or damaged accessories (sockets or extension
pieces), as these may negatively influence the accuracy of the applied
force.
• Use only within rated torque range.
• Do not use a product that has been dropped. Have it tested before
putting back into use.
Before First Use
• Check the product for transport damages.
• Remove all the packing materials.
DANGER Risk of suffocation! Keep any packaging materials
away from children – these materials are a potential source of danger,
e.g. suffocation.
4
EN
Product Description
20
60 50
90
80
40
70
30
1 0 92
100
120
140
110
150
130
8
2.5
7
11
15
6
10
14
13
9
5
12
8
4
6 5 4 37
A B
H
C D E
Front Back
F
G
ASquare drive
BDirection switch for ratchet function
CSpanner shaft
DHandle
ELock knob
FCoarse adjustment scale
GFine adjustment scale
HStorage box
Intended Use
• This product is intended to apply a specific torque force to a fastener
such as a nut or bolt.
• This product is intended for household use only. It is not intended for
commercial use.
• No liability will be accepted for damages resulting from improper use
or non-compliance with these instructions.
5
EN
Operation
Setting the torque
This product is a dual-range torque wrench marked with pound inch
(in-lb/ft-lb) and Newton meters (Nm) on opposite sides of spanner shaft
(C).
NOTICE The desired torque force is summed up by finding the
largest possible value in the coarse scale (F) that is within the desired
torque force to be applied. Use the fine adjustment scale (G) to reach the
desired value accurately.
• Twist the lock knob (E) to unlock.
• Turn the handle (D) clockwise to increase the torque and in anti-
clockwise direction to decrease the torque. The coarse and fine scale
(F, G) show the torque value.
• The precise value is set by additional turning of the handle. The
number on the fine adjustments scale at the vertical line is the added
torque to the value of the selected torque margin.
• Twist the lock knob (E) to lock.
B07SZVW98Z
Example: Setting the torque to 90 in-lb
0 010
35 in-lb 80 in-lb 90 in-lb
Example: Setting the torque to 5.65 Nm
105 0 105 0
3.95 Nm 5.65 Nm
6
EN
B07SYTQ6FT
Example: Setting the torque to 38 ft-lb
01 4 01 4 34 2
15 ft-lb 35 ft-lb 38 ft-lb
Example: Setting the torque to 47.5 Nm
01 4 01 4
20.4 Nm 47.5 Nm
B07SV45HRY
Example: Setting the torque to 68 ft-lb
02 8 02 8 80 6
20 ft-lb 60 ft-lb 68 ft-lb
7
EN
Example: Setting the torque to 94.9 Nm
02 8 02 8
27.1 Nm 94.9 Nm
B07ST25HJ5
Example: Setting the torque to 140 ft-lb
05 20 05 20 1520 10
25 ft-lb 125 ft-lb 140 ft-lb
Example: Setting the torque to 101.7 Nm
05 20 05 20
33.9 Nm 101.7 Nm
Tightening
B
A
8
EN
• Fit an extension (not included) if required to the square drive (A).
• Set ratchet function direction on the direction switch (B).
• Install properly sized socket/attachment to the square drive (A).
• Set the direction switch (B) to tighten position.
• Operate the torque wrench the same as a standard socket wrench to
tighten the bolt/nut.
• Place the socket on bolt/nut and tighten slowly and steadily until
the “click” sound is heard. Stop pulling the wrench and release the
pressure on the handle (D). The bolt/nut is now tightened to the
required torque setting.
• Do not continue to pull after the torque setting is reached. Doing so
will over-tighten the bolt/nut and could damage the wrench.
Maintenance
• The product is lubricated for life and should not be oiled. The only
exception is the ratchet mechanism which may be lubricated as
needed for smooth operation.
NOTICE This product is a precision measuring instrument.
Calibration must be done regularly to ensure accuracy. It is recommend
to re-calibrate the product no later than 10,000 cycles or 12 months after
the date it is put in service, whichever comes first.
Storage
• This product is a precision instrument and should be stored with care
using provided storage box. Avoid any vibrations and shocks.
• Set the torque to the lowest level before storage.
Specifications
Model number: B07SZVW98Z
Maximum torque value: 35 – 200 in-lb
(3.95 – 22.5 Nm)
Accuracy: +/–4 %
Net weight: approx. 1.2 lbs (560 g)
Dimensions (W x H x D): approx. 1.1 x 1 x 10.4”
(28 x 26 x 265mm)
9
EN
Model number: B07SYTQ6FT
Maximum torque value: 15 – 80 ft-lb
(20.4 – 108.5 Nm)
Accuracy: +/–4 %
Net weight: approx. 1.8 lbs (830 g)
Dimensions (W x H x D): approx. 1.4 x 1 x 14.4"
(37 x 26 x 366mm)
Model number: B07SV45HRY
Maximum torque value: 20 – 150 ft-lb
(27.1 – 203.5 Nm)
Accuracy: +/–4 %
Net weight: approx. 2.6 lbs (1.2 kg)
Dimensions (W x H x D): approx. 1.7 x 1.1 x 18.1"
(45 x 29 x 460mm)
Model number: B07ST25HJ5
Maximum torque value: 25 – 250 ft-lb
(33.9 – 338.9 Nm)
Accuracy: +/–4 %
Net weight: approx. 4.8 lbs (2.2 kg)
Dimensions (W x H x D): approx. 1.8 x 1.3 x 24.8"
(46 x 35 x 630mm)
Feedback and Help
Love it? Hate it? Let us know with a customer review.
AmazonBasics is committed to delivering customer-driven products
that live up to your high standards. We encourage you to write a review
sharing your experiences with the product.
US: amazon.com/review/review‑your‑purchases#
UK: amazon.co.uk/review/review‑your‑purchases#
US: amazon.com/gp/help/customer/contact‑us
UK: amazon.co.uk/gp/help/customer/contact‑us
10
FR
CONSIGNES DE SÉCURITÉ
IMPORTANTES
Veuillez lire attentivement les présentes instructions et les
conserver afin de pouvoir vous y référer ultérieurement. En
cas de cession de ce produit à un tiers, le présent manuel
d’utilisation doit également lui être remis.
Lors de l’utilisation du produit, vous devez toujours prendre des mesures
de sécurité de base afin de réduire tout risque de blessures, parmi
lesquelles:
• N'utilisez pas le produit pour desserrer des boulons, vis ou autres,
car cela pourrait endommager le cliquet et le calibrage de l'outil.
• N'exercez pas de force excessive sur le produit pour serrer un écrou
ou une vis. Lors du serrage, appliquez une pression constante et
régulière. À ne pas utiliser comme casse-écrou, pied-de-biche,
marteau ou levier.
• Pour éviter d'endommager le produit, cessez d’exercer toute
pression dès que vous entendez le «clic». Tenez compte du fait que
plus le couple de serrage est faible, moins le «clic» est audible.
• Le produit doit être calibré à nouveau lorsqu'il a été soumis à une
sollicitation supérieure à sa capacité nominale, après toute réparation
ou après toute manipulation inadéquate qui pourrait avoir une
influence sur son étalonnage.
• N'utilisez pas d'accessoires usés ou endommagés (douilles ou
rallonges), car ils peuvent altérer l'exactitude de la mesure de la force
déployée.
• À utiliser uniquement dans la plage de couple indiquée.
• N'utilisez pas un produit qui a subi une chute. Faites-le réviser avant
de l'utiliser à nouveau.
Avant La Première Utilisation
• Vérifiez que le produit ne présente pas de dommages dus au
transport.
• Retirez tous les matériaux d'emballage.
DANGER Risque d’étouffement! Maintenez tous les matériaux
d'emballage hors de la portée des enfants. Ces matériaux constituent
une source de danger potentiel comme l’étouffement.
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Idiomas:
Otros manuales de Herramientas de Amazon
