Amana NGD7300WW Manual de usuario

W10240584C

W10240585C-SP

Table of Contents

DRYER SAFETY ................................................................2

INSTALLATION REQUIREMENTS....................................4

Tools and Parts.................................................................... 4

Location Requirements ...................................................... 5

Electric Dryer Power Hookup-Canada Only ..................... 7

Gas Dryer Power Hookup................................................... 8

VENTING.................................................................................... 10

Venting Requirements....................................................... 10

Plan Vent System............................................................... 11

Install Vent System............................................................ 12

INSTALL LEVELING LEGS........................................................ 12

MAKE GAS CONNECTION....................................................... 13

CONNECT INLET HOSES......................................................... 13

CONNECT VENT ....................................................................... 15

LEVEL DRYER........................................................................... 15

COMPLETE INSTALLATION CHECKLIST ............................... 16

DOOR REVERSAL..................................................................... 16

STACKING WASHER AND DRYER .......................................... 16

TROUBLESHOOTING............................................................... 16

INSTALLATION NOTES

Date of purchase:_________________________________

Date of installation: _______________________________

Installer: ________________________________________

Model number: ___________________________________

Serial number: ___________________________________

Date d'achat :_____________________________________

Date d'installation : ________________________________

Installateur : ______________________________________

Numéro de modèle :________________________________

Numéro de série :__________________________________

NOTES CONCERNANT L'INSTALLATION

Table des matières

SÉCURITÉ DE LA SÉCHEUSE ....................................... 17

EXIGENCES D'INSTALLATION ...................................... 19

Outillage et pièces ............................................................ 19

Exigences d'emplacement ............................................... 20

Raccordement à l'alimentation électrique de

la sécheuse électrique - Canada seulement ................. 22

Raccordement d'une sécheuse à gaz............................. 23

L'EVACUATION ......................................................................... 25

Exigences concernant l'evacuation ................................ 25

Planication du système d'évacuation ........................... 26

Installation du circuit d'évacuation ................................. 28

INSTALLATION DES PIEDS DE NIVELLEMENT ..................... 28

RACCORDEMENT AU GAZ...................................................... 29

RACCORDEMENT DU TUYAU D'ARIVÉE D'EAU................... 29

RACCORDEMENT DU CONDUIT D'ÉVACUATION ................ 31

RÉGLAGE DE L'APLOMB DE LA SÉCHEUSE ........................ 31

ACHEVER L'INSTALLATION - LISTE DE VÉRIFICATION....... 32

INVERSION DE LA PORTE....................................................... 32

STACKING WASHER AND DRYER .......................................... 32

DÉPANNAGE ............................................................................. 32

Gas Dryer Installation Instructions

Canadian Electric Dryer Installation Instructions

Instructions pour l'installation de la sécheuse a gaz (É.-U.

et Canada) et électrique (Canada uniquement)

Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su

producto, visite:

www.whirlpool.com

Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad

superior de la puerta.

DRYER SAFETY

You

You can be killed or seriously injured if you don't immediately

can be killed or seriously injured if you don't follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the “What to do if you smell gas” instructions.

WARNING: For your safety, the information in this manual must be followed to minimize

the risk of re or explosion, or to prevent property damage, personal injury, or death.

– Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this

or any other appliance.

– WHAT TO DO IF YOU SMELL GAS:

•Do not try to light any appliance.

•Do not touch any electrical switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

•If you cannot reach your gas supplier, call the re department.

– Installation and service must be performed by a qualied installer, service agency, or

the gas supplier.

•Clear the room, building, or area of all occupants.

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

In the State of Massachusetts, the following installation instructions apply:

� Installations and repairs must be performed by a qualied or licensed contractor, plumber, or gastter qualied or licensed by

the State of Massachusetts.

� If using a ball valve, it shall be a T-handle type.

� A exible gas connector, when used, must not exceed 3 feet.

TOOLS AND PARTS

Gather the required tools and parts before starting installation.

Tools needed for all installations:

Level

Tape measure Pliers

Parts package is located in dryer drum. Check that all parts

are included.

NOTE: If installing dryer on pedestal, do not use leveling legs.

Optional Equipment: (Not supplied with dryer)

Refer to your “Use and Care Guide” for information about

accessories available for your dryer.

Parts needed: (Not supplied with dryer)

Check local codes. Check existing electrical supply and venting.

See “Electrical Requirements” and “Venting Requirements”

before purchasing parts.

Check code requirements. Some codes limit, or do not permit,

installing dryer in garages, closets, mobile homes, or sleeping

quarters. Contact your local building inspector.

Parts supplied (all models):

Flat-blade screwdriver #2 Phillips screwdriver

Adjustable wrench that

opens to 1" (25 mm) or

hex-head socket wrench

Wire stripper (direct wire

installations) Tin snips (new vent

installations)

Caulking gun and compound

(for installing new exhaust vent)

Vent clamps

1/4" nut driver

(recommended)

Tools needed for gas installations:

8" or 10" pipe wrench 8" or 10" adjustable wrench

(for gas connections)

Pipe-joint compound

resistant to LP gas

Utility knife

“Y” connector Short inlet hose

Long inlet hose Rubber washer

Parts supplied (steam models):

INSTALLATION REQUIREMENTS

Leveling legs (4)

LOCATION REQUIREMENTS

You will need:

A location allowing for proper exhaust installation.■

See “Venting Requirements.”

If using power supply cord, a grounded electrical outlet■

located within 2 ft. (610 mm) of either side of dryer.

See “Electrical Requirements”.

Floor must support dryer weight of 200 lbs. (90.7 kg).■

Also consider weight of companion appliance.

Cold water faucets located within 4 ft. (1.2 m) of the water ll■

valves, and water pressure of 20-100 psi (137.9-689.6 kPa).

You may use the water supply for your washer using the “Y”

connector and short hose (if needed) which are provided.

20-100 psi (138-690 kPa) for best performance.■

Level oor with maximum slope of 1" (25 mm) under entire■

dryer. If slope is greater than 1" (25 mm), install Extended

Dryer Feet Kit, Part Number 279810. If not level, clothes

may not tumble properly and automatic sensor cycles may

not operate correctly.

For garage installation, place dryer at least 18" (460 mm)■

above oor. If using a pedestal, you will need 18" (460 mm)

to bottom of dryer.

For each arrangement, consider allowing more space for ease

of installation and servicing; spacing for companion appliances

and clearances for walls, doors, and oor moldings. Space

must be large enough to allow door to fully open. Add spacing

on all sides of dryer to reduce noise transfer. If a closet door

or louvered door is installed, top and bottom air openings

in door are required.

Side view:

DRYER DIMENSIONS

Front view:

27"

(686 mm)

(25 mm)

353/8"

(899 mm)

31/2"

(89 mm)

29"

(736 mm)

Left or

right side

exhaust

67/8"

(174 mm)

15/8"

(41 mm)

471/8"

(1197 mm)

481/8"

(1238 mm)

Door open view:

Back view:

NOTE: Most installations require a minimum of 5" (127 mm)

clearance behind dryer for exhaust vent with elbow. See “Venting

Requirements”.

IMPORTANT: Do not operate, install, or store dryer where

it will be exposed to water, weather, or at temperatures below

45° F (7° C). Lower temperatures may cause dryer not to

shut off at end of automatic sensor cycles, resulting in longer

drying times.

Cabinet installation (dryer only):

Closet installation (dryer only):

Spacing for recessed area or closet installation

All dimensions show recommended spacing allowed, with tested

spacing of 0" (0 mm) clearance on sides and rear.

Additional spacing should be considered for ease of■

installation and servicing.

Additional clearances might be required for wall, door, and■

oor moldings.

Additional spacing should be considered on all sides of the■

dryer to reduce noise transfer.

For closet installation, with a door, minimum ventilation■

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilitation openings are

acceptable.

Companion appliance spacing should also be considered.■

61/4"

(159 mm)

281/8"

(715 mm)

31/2"

(89 mm)

14"

(358 mm)

Electric

24 in.2

(155 cm2)

48 in.2

(310 cm2)

(25 mm)

(102 mm)

(76 mm)

34" recommended

(864 mm)

18" min.

(457 mm)

(76 mm)

(25 mm)

(102 mm)

(178 mm)

18"

(460 mm)

Custom under counter installation (dryer only):

Closet Installation (stacked washer and dryer):

NOTE: Some models not recommended for undercounter

installation.

Mobile home - Additional installation requirements:

This dryer is suitable for mobile home installations.

The installation must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR,

Part 3280 (formerly the Federal Standard for Mobile home

construction and Safety, Title 24, HUD Part 280) or Standard

CAN/CSA-Z240 MH.

Mobile home installations require:

All dryers:

Metal exhaust system hardware, available for purchase■

from your dealer. For further information, see “Assistance

or Service” section in your “Use and Care Guide”.

Special provisions must be made in mobile homes to■

introduce outside air into dryer. Openings (such as a

nearby window) should be at least twice as large as

dryer exhaust opening.

For gas dryers mobile home installations:

Mobile Home Installation Hold-down Kit Part Number■

346764 is available to order. For further information, see

“Assistance or Service” section in your “Use and Care

Guide”.

(25 mm)

51/2"

(140 mm) 24 in.2

(155 cm2)

48 in.2

(310 cm2)

(76 mm)

(152 mm)

76"

(1930 mm)

(25 mm)

39" min.

(990 mm)

ELECTRIC DRYER

POWER HOOKUP- CANADA ONLY

ELECTRICAL REQUIREMENTS

WARNING

Electrical Shock Hazard

Plug into a grounded 4 prong outlet.

Failure to do so can result in death or electrical shock.

It is your responsibility:

To contact a qualied electrical installer.■

To be sure that the electrical connection is adequate and in■

conformance with Canadian Electrical Code, C22.1-latest

edition and all local codes. A copy of above codes standard

may be obtained from: Canadian Standards Association,

178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

To supply the required 4 wire, single phase, 120/240 volt,■

60 Hz, AC only electrical supply on a separate 30-amp

circuit, fused on both sides of the line. A time-delay fuse or

circuit breaker is recommended. Connect to an individual

branch circuit.

This dryer is equipped with a CSA International Certied■

Power Cord intended to be plugged into a standard 14-30R

wall receptacle. The cord is 5 ft. (1.52 m) long. Be sure wall

receptacle is within reach of dryer’s nal location.

4-wire receptacle (14-30R)

If using a replacement power supply cord, it is recommended that

you use Power Supply Cord Replacement Part Number 9831317.

For further information, please reference service numbers located

in “Assistance or Service” section of your “Use and Care Guide”.

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

� For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualied electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not t the outlet, have a proper outlet

installed by a qualied electrician.

GAS DRYER POWER HOOKUP

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

re, or electrical shock.

WARNING

120 Volt, 60 Hz, AC only, 15- or 20- amp fused electrical■

supply is required. A time-delay fuse or circuit breaker is

recommended. It is also recommended that a separate

circuit serving only this dryer be provided. GAS TYPE

Natural Gas:

This dryer is equipped for use with Natural gas. It is

design-certied by CSA International for LP (propane or

butane) gases with appropriate conversion.

Your dryer must have the correct burner for the type of gas■

in your home. Burner information is located on the rating

plate in the door well of your dryer. If this information does

not agree with the type of gas available, contact your dealer

or call the phone numbers referenced in the “Assistance or

Service” section of your “Use and Care Guide”.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualied person make sure

gas pressure does not exceed 13" (330 mm) water

column.

Examples of a qualied person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or re.

GAS SUPPLY REQUIREMENTS

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

� For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualied electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not t the outlet, have a proper outlet

installed by a qualied electrician.

†®TEFLON is a registered trademark of E.I. Dupont De Nemours and Company.

1/2" IPS pipe is recommended.■

3/8" approved aluminum or copper tubing is acceptable for■

lengths under 20 ft. (6.1 m) if local codes and gas supplier

permit.

If you are using Natural gas, do not use copper tubing.■

Lengths over 20 ft. (6.1 m) should use larger tubing and■

a different size adapter tting.

If your dryer has been converted to use LP gas, 3/8" LP■

compatible copper tubing can be used. If the total length of

the supply line is more than 20 ft. (6.1 m), use larger pipe.

NOTE: Pipe-joint compounds that resist the action of LP gas

must be used. Do not use TEFLON®† tape.

Must include shut-off valve■

In the U.S.A.:

An individual manual shut-off valve must be installed within

six (6) ft. (1.8 m) of the dryer in accordance with the National

Fuel Gas Code, ANSI Z223.1. The location should be easy to

reach for opening and closing.

In Canada:

An individual manual shut-off valve must be installed in

accordance with the B149.1, Natural Gas and Propane

Installation Code. It is recommended that an individual

manual shutoff valve be installed within six (6) ft. (1.8 m) of

the dryer. The location should be easy to reach for opening

and closing.

A. 3/8" exible gas connector

B. 3/8" pipe to are adapter tting

C. 1/8" NPT minimum plugged tapping

D. 1/2" NPT gas supply line

E. Gas shutoff valve.

LP Gas Conversion:

IMPORTANT: Conversion must be made by a qualied

technician.

No attempt shall be made to convert the dryer from the gas

specied on the model/serial rating plate for use with a different

gas without consulting your gas company.

GAS SUPPLY LINE

Must include 1/8" NPT minimum plugged tapping accessible■

for test gauge connection, immediately upstream of the gas

connection to the dryer.

GAS SUPPLY CONNECTION REQUIREMENTS

Use an elbow and a 3/8" are x 3/8" NPT adapter tting■

between the exible gas connector and the dryer gas pipe,

as needed to avoid kinking.

Use only pipe-joint compound. Do not use TEFLON■®† tape.

This dryer must be connected to the gas supply line with a■

listed exible gas connector that complies with the standard

for connectors for gas appliances, ANSI Z21.24 or CSA 6.10.

BURNER INPUT REQUIREMENTS

Elevations above 10,000 ft. (3,048 m):

When installed above 10,000 ft. (3,048 m) a 4% reduction■

of the burner Btu rating shown on the model/serial number

plate is required for each 1,000 ft. (305 m) increase in

elevation.

Gas supply pressure testing

The dryer must be disconnected from the gas supply piping■

system during pressure testing at pressures greater than

1/2 psi.

DRYER GAS PIPE

The gas pipe that comes out through the rear of your dryer■

has a 3/8" male pipe thread.

*6¼"

(159 mm)

1½"

(38 mm)

A. 3/8" NPT dryer pipe

*NOTE: If the dryer is mounted on a pedestal, the gas pipe height

must be an additional 10" (254 mm) or 15.5" (394 mm) from the

oor, depending on the pedestal model. For a garage installation,

the gas pipe height must be an additional 18" (460 mm) from

the oor.

A. 3/8" NPT dryer pipe

VENTING REQUIREMENTS

WARNING

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or re.

WARNING: To reduce the risk of re, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, attic, crawlspace, or a concealed space

of a building. Only rigid or exible metal vent shall be used for

exhausting.

VENTING

Only a 4" (102 mm) heavy metal exhaust vent and clamps■

may be used.

Do not use plastic or metal foil vent.■

Rigid metal vent:

Recommended for best drying performance and to avoid■

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

Must be fully extended and supported in nal dryer location.■

Remove excess to avoid sagging and kinking that may■

result in reduced airow and poor performance.

Do not install in enclosed walls, ceilings, or oors.■

The total length should not exceed 7■3/4ft. (2.4 m).

NOTE: If using an existing vent system, clean lint from

entire length of the system and make sure exhaust hood

is not plugged with lint. Replace plastic or metal foil vents

with rigid metal or exible metal vents. Review Vent System

Chart and if necessary, modify existing vent system to

achieve best drying performance.

(102 mm)

4" (102 mm) heavy metal exhaust vent

Louvered Hood

Good

Angled Hood

Box Hood

Better

Exhaust hoods:

Elbows:

Recommended Styles:

45° elbows provide better airow than 90° elbows.■

Clamps:

Use clamps to seal all joints.■

Exhaust vent must not be connected or secured with screws■

or other fastening devices that extend into interior of duct

and catch lint. Do not use duct tape.

Must be at least 12" (305 mm) from ground or any object that■

may obstruct exhaust (such as owers, rocks, bushes, or

snow).

Acceptable Style:

Vent products can be purchased from your dealer. For more

information, see “Assistance or Service” section in your “Use and

Care Guide”.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Secadora de Amana

Amana

Amana TANDEM W10240880A Manual de usuario

Amana

Amana LEA10AW Manual de usuario

Amana

Amana NGD5500TQ Manual de usuario

Amana

Amana LEA10AW Manual de usuario

Amana

Amana NED5700B Manual de usuario

Amana

Amana SDE515DAYW Manual

Amana

Amana ALE230RAW Manual de usuario

Amana

Amana LED32AW-PLED32AW Manual de usuario

Amana

Amana LE4427 Manual de usuario

Amana

Amana NED4800VQ1 Guía de solución de problemas

Amana

Amana LED20AW Manual de usuario

Amana

Amana LEA20AW Manual de usuario

Amana

Amana Clothes Dryer Manual de usuario

Amana

Amana LE8367L2 Manual de usuario

Amana

Amana W10216186A Manual de usuario

Amana

Amana NTW5400T Manual de lista de piezas

Amana

Amana LE7163WM/LM Manual de usuario

Amana

Amana ALG866SAC Manual

Amana

Amana NED7033W Manual de lista de piezas

Amana

Amana NED4500VQ Manual de lista de piezas

Amana

Amana NGD5700B Manual de usuario

Amana

Amana NGD7500VW Manual de usuario

Amana

Amana Home Laundry Dryers Manual de usuario

Amana

Amana LE4207W/L2 Manual de usuario

Manuales populares de Secadora de otras marcas

Bosch

Bosch WTA79200GB Manual de usuario

Miele

Miele TWH 780 WP Manual de usuario

Asko

Asko T760 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Manual de usuario

Bosch

Bosch Logixx 10 WTB76556GB Hoja de especificaciones

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Manual de instrucciones

Electrolux

Electrolux EW2H328R2 Manual de usuario

Beko

Beko DS8433RX1M Manual de usuario

Dawlance

Dawlance Spinner DS 6000 C Manual de usuario

Electrolux

Electrolux TP5080TW Manual de usuario

AEG

AEG TR838P4OB Manual de usuario

Indesit

Indesit IDV 75 Manual de usuario

Infiniton

Infiniton SD-DG85C Manual de usuario

BOMANN

BOMANN WT 5019 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Manual de usuario

Asko

Asko T793C Manual de usuario

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manual de usuario

Frigidaire

Frigidaire CAQE7077KW0 Manual del propietario