AM TECH mobile pro advance Manual de usuario
U
Us
se
er
r’
’s
s
M
Ma
an
nu
ua
al
l
F
Fo
or
r
M
Mo
ob
bi
il
le
e
P
Pr
ro
o
A
Ad
dv
va
an
nc
ce
e
U
s
e
r’s
M
a
n
u
a
l
2
Record of Revisions
Revision Version Date DESCRIPTION
1.00
25-Jan-2008
Preliminary
3
Table of Contents
INTRODUCTION …………………………………………………………………………………3
1. Specifications & Features …………..………………………………………………
TechnicalInformation………………………………………………..........................4
Product Features ……………………………………………………………………...5
2. Unpacking ………….……………………………………………………………………....6
3. The Name of Parts and Indicator on Control Panel ………………………………...7
4. Installation ………………………………………………………………………………….8
Paper Loading …………………………………………………………………………8
Replacing the Battery………………………………………………………………….8
Swipe Card……………………………………………………………………………..9
Smart Card ………...…………………………………………………………………..9
How to charge …………………………………………………………………………10
5. Interface …………………………………………………………………………………….11
Communication by Bluetooth ..............................................................................11
Communication by Serial Port(Cable) ………………………………………………12
6. Troubleshooting……….…………………………………………………………………..13
7. Self Test ………………………………………………………………………………….…13
8. Cleaning...…………………………………………………………………………………..14
9. Warning...…………………………………………………………………………………...14
10. Contact to your retailer ………………………………………………………………..15
4
INTRODUCTION
All rights reserved. Total or partial reproduction of this manual in whatever form, whether by
printed or electronic means, is forbidden. While guaranteeing that the information contained in it
has been carefully checked, AM TECH CO., LTD. and other entities utilized in the realization of
this manual bear no regarding any errors found in it or suggestions on how it could be improved
are appreciated. Since products are subject to continuous check and improvement, AM TECH
Co., LTD. reserves the right to make changed in information contained in this manual without
prior notification.
Copyright 2006AM TECH CO., LTD. – KOREA
5
1. Specifications & Features
Technical Specifications
Printer Method Direct Line Thermal Printing
Printing width 48mm
Resolution 8dots/mm(203dpi)
Printing Speed 40mm/ sec *1
Operating Voltage DC 5V
Size of the Buffer 128KB
Graphic(logo) Available
Barcode JAN13, EAN8, UPC-A, UPC Code39, Code 128
Card Reader JIS-I,II and ISO-1/2, IC Card (EMV LEVEL 1)
Interface Bluetooth(1.2Ver), RS232C, USB
Baud Rate 9600bps (default) or 38400bps
DC Power Pack Rechargeable 7.4V 1050mA(Li-ion)
Power Supply Input : 100~250V, AC 50~60 Hz
Output : 8.4V 0.8A
Paper Width 58mm
Paper Length 18.3m
Paper Diameter 38mm
Dimensions 84(W) X 128(L) X 48(H)mm
Weight About 311g
- With Magnetic Card Reader: About 318g
- With Smart Card Reader: About 326g
- With both Reader: About 333g
Operation Temperature 5 ~ 40℃
Storage Temperature -20℃~ 80℃
Storage Humidity 20% ~ 80%
Head Life Approximately 50km
*1 There is also case that the printing speed will not follow as specification under condition.
6
1.2 Product Features
This Printer is a compact light weight portable thermal printer powered by a 7.4V 1050mA
(Li-ion) battery.
Smart Card & MSR
This printer can be supported Magnetic Stripe Reader & Smart Card Reader as optional
feature.
High Resolution
This printer boosts printing precise characters and clear image at high resolution of
8dots/mm.
Easy Paper Loading
Paper roll can be loaded easily and replaced quickly by clamshell design.
Very Silent printing
This printer prints silently through the direct thermal printing method
High Speed
This printer has a maximum speed of 40mm/sec. *1
Compact & Light Weight
This printer is designed as a newly developed compact light weight (311g *2) printer,
so that it is suitable for hand-held use.
Bluetooth & Rs232CCable
Laptops, PDA and mobile phones via the Bluetooth and serial cable,
*1. There is also case that the printing speed will not follow as specification under condition.
*2. With Magnetic Stripe Reader(318g)
With Smart Card Reader(326g)
With Both Reader(333g)
7
2. Unpacking
The illustration below shows the items should included for the standard of Mobile ProAdvance
Package. If any items are damaged or missing, please, contact with your dealer for assistance.
User’s Manual
Communication Cable
Paper Roll 2pcs
Battery Charger
Power Code
Printer
Buffer material
8
Power switch
Reset
3. The Name of Parts and Indicator on Control Panel
Power
Status Description
Power light “On” Power light is “Green LED”. And then, Blinking the “Red
LED” at twice
Power light ”off” Power cable is not connected with printer
Charger
On charging Charger light is on “orange”
✽Note: regarding full charging, check the LED on the battery charger.
Error
ERROR light is “On”(not blinking),
and heard beeper sound
Turn off the printer and check if cutter was seized
ERROR light is “Blinking” Make sure that the printer cover is properly closed. Press
the printer cover audibly clicks into place.
ERROR light is Off, but nothing is
printed
Try to run the self test to check that the printer works
properly. See the self test instructions Chapter 7.
This indicates an error. See Chapter 6 for information on what to do when this light comes on.
Paper Cover
Cover button
Power
Interface
Power Charger Error
9
4. Installation
4.1 Paper Loading
Open the paper cover and put the paper roll supplied by a distributor into the holder and,close
the cover
CAUTION:
Do not touch the print head because it can be very hot after printing continuously for a long time.
4.2 Replacing the Battery
It happens to print poorly when the battery power is low. It
needs to check regularly the battery condition every six
months. And change it as the showed picture.
Power: 7.4V 1,050mAH Lithium-ion
Average Life: Six month after date written by on battery
1. Make sure the printer is turned off
2. Remove the screw from the Battery cover. Then
take off the battery cover, as shown the side
illustration.
3. Unplug the battery from connection and then,
replace new battery to make sure that connecter
is plugged correctly. Then secure it with the screw.
CAUTION:
Make sure that you use the optional 7.4V 1,050mAH Lithium-ion battery which is supplied “as
genuine part” by manufacture. Using an incorrect Battery may be caused fire or electrical
shock.
10
4.3 Swipe card
Swipe the card at constant speed in the same direction with the arrow in the picture.
When the card is read correctly, the printer sounds with “beep~” once.
When the card is read incorrectly, the “Red LED” on the printer brinks at twice with sounding
“beep~ beep~”
4.4 Smart Card
Put the smart card at the constant strength in the same direction with the arrow in the picture.
Pls, refer to the technical document for details that are including specification and how to use it.
Tabla de contenidos
Otros manuales de Impresora de AM TECH
