Altronix T1CVK3F4 Manual de usuario

T1CVK3F4

4 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove1 enclosure with TC1 Altronix/CDVI backplane

- One (1) eFlow6NB - Power Supply/Charger

- One (1) ACM4 - Fused Access Power Controller

T2CVK7F10

10 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove2 enclosure with TCV2 Altronix/CDVI backplane

- One (1) eFlow104NB - Power Supply/Charger

- One (1) ACM8 - Fused Access Control Module

- One (1) ACM4 - Fused Access Control Module

- One (1) PD8UL - Fused Power Distribution Module

T2CVK33F10

10 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove2 enclosure with TCV2 Altronix/CDVI backplane

- Two (2) eFlow6NB - Power Supply/Chargers

- Two (2) MOM5 - PTC Power Distribution Modules with

Fire Alarm Interface

T2CVK33F10Q

10 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove2 enclosure with TCV2 Altronix/CDVI backplane

- One (1) LINQ2 - Network Communication Module

- Two (2) eFlow6NB - Power Supply/Chargers

- Two (2) MOM5 - PTC Power Distribution Modules with

Fire Alarm Interface

T3CVK77F20

20 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove3 enclosure with TCV3 Altronix/CDVI backplane

- Two (2) eFlow104NB - Power Supply/Chargers

- Two (2) ACM8 - Fused Access Control Modules

- One (1) ACM4 - Fused Access Control Module

- One (1) PD8UL - Fused Power Distribution Module

- One (1) RSB2 - Rocker Switch Bracket with

Two (2) Rocker Switches (Not evaluated by UL

Access & Power Integration

Altronix/CDVI Kits

Models Include:

Rev. TCVK_042619

Installing Company: _________________________ Service Rep. Name: __________________________________________

Address: _________________________________________________________ Phone #: _________________________

All registered trademarks are property of their respective owners. More than just power.™

Installation Guide

All components of this Trove kit are UL Listed sub-assemblies.

Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

- 2 - Trove CDVI Kits Installation Guide

Overview:

Altronix Trove CDVI kits are pre-assembled and consist of Trove enclosures/backplanes with factory installed Altronix power supply/chargers and

sub-assemblies. These kits also accommodate various combinations of CDVI Atrium A22K/A22NB/ADH10 boards for up to twenty (20) doors

in a single enclosure.

Configuration Chart:

Altronix

Model Number

Networkable

Power Supply Board

Input Fuse Rating

Power Supply Board

Battery Fuse Rating

120VAC 60Hz

Input Current (A)

Maximum Supply

Current for Main and

Aux. Outputs on

Power Supply board,

MOM5 power

distribution module

or ACM4/ACM8 Access

Power Controllers’

outputs

Nominal DC

Output Voltage

Fail-Safe/Fail-Secure or

Dry Form “C” Outputs

Additional Fuse or PTC

Protected Outputs

ACM4/ACM8 Board

Input Fuse Rating

ACM4 Board Output Fuse

Rating

ACM8 Board Output Fuse

Rating

PD8UL Board

Output Fuse Rating

MOM5 Output

PTC Rating

Power Supply

[DC] [Aux]

Output

Range

(VDC)

Output

Range

(VDC)

T1CVK3F4 – 5A/250V 15A/

32V 3.5 24VDC @ 5.7A 20.17-

26.4

20.28-

26.4 4 – 10A/

250V

3A/

32V –––

T2CVK7F10 – 6.3A/250V 15A/

32V 4.5 24VDC @ 9.4A 20.17-

26.4

20.28-

26.4 12 8 10A/

250V

2.5A/

250V

2.5A/

250V

3.5A/

250V –

T2CVK33F10 – 5A/250V 15A/

32V 7.0

24VDC @ 5.9A

20.17-

26.4

20.28-

26.4 – 10 – – – – 2A/

250V

T2CVK33F10Q P5A/250V 15A/

32V 7.0

24VDC @ 5.9A

20.17-

26.4

20.28-

26.4 – 10 – – – – 2A/

250V

T3CVK77F20 –6.3A/ 250V 15A/

32V 9.0

24VDC @ 9.4A

24VDC @ 9.7A

20.17-

26.4

20.28-

26.4 20 8 10A/

250V

3A/

32V

2.5A/

250V

3.5A/

250V –

9.7-

13.2

10.03-

13.2

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.

Product is intended for indoor use only.

1. Remove backplane from enclosure. Do not discard hardware.

If your application requires a raised backplane, re-mount it using metal spacers and screws (provided).

2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install two/three upper fasteners and screws

in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the two/three upper screws; level and secure.

Mark the position of the lower two/three holes. Remove the enclosure. Drill the lower holes and install the fasteners. Place the

enclosure’s upper keyholes over the upper screws. Install the lower screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switch(es) (Altronix Model TS112 or equivalent) in desired location, opposite hinge. Slide the

tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 2). Connect tamper switch wiring

to the Access Control Panel input or the appropriate UL Listed reporting device. To activate alarm signal open the door of the enclosure.

4. Mount CDVI A22K/A22NB/ADH10 boards to backplane, refer to pages 3-6.

5. Refer to the eFlow Power Supply/Charger Installation Guide (eFlow6NB, eFlow102NB,

eFlow104NB) and corresponding Sub-Assembly Installation Guide (LINQ2, ACM4, ACM8,

PD8UL, MOM5) for further installation instructions.

Fig. 1

Tamper Switch

(provided)

To Access Control Panel or

UL Listed Reporting Device

Edge of

Enclosure

Trove CDVI Kits Installation Guide - 3 -

T1CVK3F4: Configuration of CDVI A22K/A22NB/ADH10 Boards

1. Fasten spacers (supplied with A22K/A22NB/ADH10) to CDVI A22K/A22NB/ADH10 board (Fig. 2b, pg. 3).

2. Mount CDVI A22K/A22NB/ADH10 boards into the correct positions (Fig. 2, pg. 3) by postioning spacers over appropriate holes

on the backplane and depressing down on board to secure spacer to the backplane (Fig. 2a, 2b, pg. 3).

Note: CDVI A22K/A22NB/ADH10 boards have one (1) RJ45 jack each.

Please make sure that they are mounted correctly, as shown in Fig. 2 below.

3. Fasten backplane to Trove2 enclosure utilizing pan head screws (provided).

Fig. 2

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

NC C NO NC C NO

AC FAIL BAT FAIL

TRIGGER

AC DCAC1

EOL NO GND

SUPERVISED RESET

+AUX-

- BAT +-DC +

Altronix - eFlow6NB

L G N

OFF - 24V

ON - 12V

--- +

Control

--- +

Power

NO C NC

FACP INTERFACE

+ INP --- T + RET ---

TRG

TRIGGER

INPUT

IN GND

NC C NO COM

OUTPUT 1

NC C NO COM

OUTPUT 2

NC C NO COM

OUTPUT 3

NC C NO COM

OUTPUT 4

IN GND

LED1 LED2 LED3 LED4

SW1 SW2 SW3

SW4

MAIN

Altronix - ACM4

Spacer

CDVI - A22K/A22NB/ADH10

Access Controller

Backplane

Fig. 2a

Plastic Spacer

pre-mounted into

CDVI Atrium modules

Insert into

TC1 backplane

Fig. 2b

- 4 - Trove CDVI Kits Installation Guide

T2CVK7F10: Configuration of CDVI A22K/A22NB/ADH10 Boards

1. Fasten spacers (supplied with A22K/A22NB/ADH10) to CDVI A22K/A22NB/ADH10 board (Fig. 3b, pg. 4).

2. Mount CDVI A22K/A22NB/ADH10 boards into the correct positions (Fig. 3, pg. 4) by postioning spacers over appropriate holes

on the backplane and depressing down on board to secure spacer to the backplane (Fig. 3a, 3b, pg. 4).

Note: CDVI A22K/A22NB/ADH10 boards have one (1) RJ45 jack each.

Please make sure that they are mounted correctly, as shown in Fig. 3 below.

3. Fasten backplane to Trove2 enclosure utilizing pan head screws (provided).

Altronix eFlow104NB

OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8

NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM

IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND

1 2 3 4 5 6 7 8

INPUT

TRIGGER

10A 250V

+INP- T + RET-

NO C NC

FACP INTERFACE

Power Control

- + - +

F1 F2 F3 F4 F5 F6 F7 F8

MAIN

TRG

FACP

1 2 3 4

Altronix

ACM8

--- +

Control

--- +

Power

NO C NC

FACP INTERFACE

+ INP --- T + RET ---

TRG

TRIGGER

INPUT

IN GND

NC C NO COM

OUTPUT 1

NC C NO COM

OUTPUT 2

NC C NO COM

OUTPUT 3

NC C NO COM

OUTPUT 4

IN GND

LED1 LED2 LED3 LED4

SW1 SW2 SW3

SW4

MAIN

Altronix

ACM4

COMMON POWER OUTPUTS

FUSED POWER OUTPUTS

1 2 3 4 5 6 7 8

INPUT

P N

Altronix PD8UL

--- BAT + --- DC +

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

Fig. 3

Spacer

CDVI - A22K/A22NB/ADH10

Access Controller

Backplane

Fig. 3a

Plastic Spacer

pre-mounted into

CDVI Atrium modules

Insert into

TCV2 backplane

Fig. 3b

Trove CDVI Kits Installation Guide - 5 -

T2CVK33F10 and T2CVK33F10Q: Configuration of CDVI A22K/A22NB/ADH10 Boards

1. Fasten spacers (supplied with A22K/A22NB/ADH10) to CDVI A22K/A22NB/ADH10 board (Fig. 4b, pg. 5).

2. Mount CDVI A22K/A22NB/ADH10 boards into the correct positions (Fig. 4, pg. 5) by postioning spacers over appropriate holes

on the backplane and depressing down on board to secure spacer to the backplane (Fig. 4a, 4b, pg. 5).

Note: CDVI A22K/A22NB/ADH10 boards have one (1) RJ45 jack each.

Please make sure that they are mounted correctly, as shown in Fig. 4 below.

3. Fasten backplane to Trove2 enclosure utilizing pan head screws (provided).

NC C NO NC C NO

AC FAIL BATFAIL

TRIGGER

AC DCAC1 EOLNOGND

SUPERVISED RESET +AUX-

- BAT +-DC +

L G N

OFF - 24V

ON - 12V

NC C NO NC C NO

AC FAIL BATFAIL

TRIGGER

AC DCAC1 EOLNOGND

SUPERVISED RESET +AUX-

- BAT +-DC +

L G N

OFF - 24V

ON - 12V

- DC INPUT +

POS (+) DC OUTPUT (ALARM)

POS (+) DC OUTPUT (STANDBY)

6 7 8 9 10

1 2 3 4 5

TRIGGER

LED

POWER

ON LED

NEG1 NEG2 NEG3 NEG4 NEG5

TRIGGER

NC C NO NC C NO

DRY OUTPUT POWER FAIL

- INPUT +

- DC INPUT +

POS (+) DC OUTPUT (ALARM)

POS (+) DC OUTPUT (STANDBY)

6 7 8 9 10

1 2 3 4 5

TRIGGER

LED

POWER

ON LED

NEG1 NEG2 NEG3 NEG4 NEG5

TRIGGER

NC C NO NC C NO

DRY OUTPUT POWER FAIL

- INPUT +

LINQ2 Module (T2CVK33F10Q)

Altronix - eFlow6NB

Altronix

MOM5

Altronix

MOM5

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

Fig. 4

Spacer

CDVI - A22K/A22NB/ADH10

Access Controller

Backplane

Fig. 4a

Plastic Spacer

pre-mounted into

CDVI Atrium modules

Insert into

TCV2 backplane

Fig. 4b

- 6 - Trove CDVI Kits Installation Guide

T3CVK77F20: Configuration of CDVI A22K/A22NB/ADH10 Boards

1. Fasten spacers (supplied with A22K/A22NB/ADH10) to CDVI A22K/A22NB/ADH10 board (Fig. 5b, pg. 6).

2. Mount CDVI A22K/A22NB/ADH10 boards into the correct positions (Fig. 5, pg. 6) by postioning spacers over appropriate holes

on the backplane and depressing down on board to secure spacer to the backplane (Fig. 5a, 5b, pg. 6).

Note: CDVI A22K/A22NB/ADH10 boards have one (1) RJ45 jack each.

Please make sure that they are mounted correctly, as shown in Fig. 5 below.

3. Fasten backplane to Trove3 enclosure utilizing pan head screws (provided).

Altronix - eFlow104NB

– DC +– BAT +

L G N

Altronix - eFlow104NB

– DC +– BAT +

L G N

OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8

NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM

IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND

1 2 3 4 5 6 7 8

INPUT

TRIGGER

10A 250V

+INP- T + RET-

NO C NC

FACP INTERFACE

Power Control

- + - +

F1 F2 F3 F4 F5 F6 F7 F8

MAIN

TRG

FACP

1 2 3 4

OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8

NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM

IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND

1 2 3 4 5 6 7 8

INPUT

TRIGGER

10A 250V

+INP- T + RET-

NO C NC

FACP INTERFACE

Power Control

- + - +

F1 F2 F3 F4 F5 F6 F7 F8

MAIN

TRG

FACP

1 2 3 4

Altronix - ACM8

TRG

TRIGGER

INPUT

LED1 LED2 LED3 LED4

MAIN

OUTPUT 1

NC C NO COM NC C NO COM NC C NO COM NC C NO COM

OUTPUT 2 OUTPUT 3

IN GND

OUTPUT 4

-- +

CONTROL

-- +

POWER

+INP- T +RET-

INTERFACE

NO C NC

FACP

Altronix

ACM4

COMMON POWER OUTPUTS

FUSED POWER OUTPUTS

1 2 3 4 5 6 7 8

INPUT

P N

R1 LED

Altronix - PD8UL

RSB2

Altronix - ACM8

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

CDVI - A22K/A22NB/ADH10

RJ45 Jack

Fig. 3

Spacer

CDVI - A22K/A22NB/ADH10

Access Controller

Backplane

Fig. 6a

Plastic Spacer

pre-mounted into

CDVI Atrium modules

Insert into

TCV3 backplane

Fig. 6b

Trove CDVI Kits Installation Guide - 7 -

eFlow Power Supply/Chargers can be Controlled and Monitored while

Reporting Power/Diagnostics from Anywhere over the Network...

LINQ2 Mounts Inside any Trove Enclosure

LINQ2 - Network Communication Module

LINQ2 provides remote IP access to real-time data from eFlow power supply/chargers to help keep systems up

and running at optimal levels. It facilitates fast and easy installation and set-up, minimizes system downtime,

and eliminates unnecessary service calls, which helps reduce Total Cost of Ownership (TCO) - as well as creat-

ing a new source of Recurring Monthly Revenue (RMR).

LINQ2

Features:

- UL Listed in the U.S. and Canada.

- Local or remote control of up to (2) two Altronix eFlow power output(s) via LAN and/or WAN.

- Monitor real time diagnostics: DC output voltage, output current, AC & battery status/service, input trigger state change,

output state change and unit temperature.

- Access control and user managment: Restrict read/write, Restrict users to speciﬁc resources

- Two (2) integral network controlled Form “C” Relays.

- Three (3) programmable input triggers: Control relays and power supplies via external hardware sources.

- Email and Windows Dashboard notiﬁcations

- Event log tracks history.

- Secure Socket Layer (SSL).

- Programmable via USB or web browser - includes operating software and 6 ft. USB cable.

LINQ2 Module

Altronix eFlow

Power Supply

Network Connection:

Installation, Programming

and Monitoring

- 8 - Trove CDVI Kits Installation Guide

Notes:

- 9 - Trove CDVI Kits Installation Guide

Notes:

- 10 - Trove CDVI Kits Installation Guide

T1CVK3F4 (Trove1) Enclosure Dimensions (H x W x D approximate):

18” x 14.5” x 4.625” (457mm x 368mm x 118mm)

4.5” (114.3mm) 4.5” (114.3mm) 2.75”

(69.9mm)

1.115” (28.3mm)

1.36” (34.5mm)

1.25” (31.8mm) 1.25” (31.8mm)

1.5” (38.1mm)

8.5” (215.9mm)6.5” (165.1mm)

1.5” (38.1mm)

8.5” (215.9mm)6.5” (165.1mm)

4.5” (114.3mm)

13.0” (330.2mm)

0.6” (15.2mm)

14.5” (321.3mm)

1.45” (36.8mm)

7.25” (184.2mm)

1.95” (49.5mm)

1.1” (27.9mm)

0.6” (15.2mm)

0.57” (14.5mm)

18.0” (457.2mm)

1.25” (31.8mm)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Fuente de alimentación de Altronix

Altronix

Altronix TROVE T1KE34D Manual de usuario

Altronix

Altronix ALTV248ULHi Instrucciones de funcionamiento y mantenimiento

Altronix

Altronix TROVE Trove1SP1 Manual de usuario

Altronix

Altronix eFlow104N Series Manual de usuario

Altronix

Altronix ALTV1224DC Manual de usuario

Altronix

Altronix LTV615DC48M220 Manual de usuario

Altronix

Altronix Trove T3MK7716S Manual de usuario

Altronix

Altronix ALTV2416 Series Manual de usuario

Altronix

Altronix SMP7PM Manual de usuario

Altronix

Altronix ALTV615DC8ULCB Manual de usuario

Altronix

Altronix AL168 Series Manual de usuario

Altronix

Altronix OLS75 Manual de usuario

Altronix

Altronix OLS75 Manual de usuario

Altronix

Altronix OLS250 Manual de usuario

Altronix

Altronix OLS250 Manual de usuario

Altronix

Altronix AL600ULX Series Manual de usuario

Altronix

Altronix TROVE T1RAL3F8 Manual de usuario

Altronix

Altronix ALTV615DC48CBM220 Instrucciones de funcionamiento y mantenimiento

Altronix

Altronix R2432UL Series Manual de usuario

Altronix

Altronix AL1012ULX Series Manual de usuario

Altronix

Altronix WayPoint10A Series Manual de usuario

Altronix

Altronix WayPoint562 Manual de usuario

Altronix

Altronix eFlow104NV Manual de usuario

Altronix

Altronix SMP1012X Series Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario