Altronix NetWaySP2P Manual de usuario
Overview:
Altronix NetWaySP2P hardened media converter/injector converts a single Fiber (1000Base-X/SX/LX)
into two (2) Ethernet ports (10/100/1000 Mbps) and provides PoE/PoE+ power to connected devices.
Mounted in compact insulated housing, it features auto detection and protection of legacy non-PoE
cameras/devices.
Features:
Rev.112817
Installation Guide
NetWaySP2P
2-Port Powered Media Converter/Injector
Agency Listings:
• CE European Conformity.
Input:
• 48-56VDC @ 1.2A (60W).
Fiber Port:
Refer to page 3 for recommended SFP modules.
• One (1) 1Gb SFP port.
Output Power:
• Two (2) PoE / PoE+ ports, rated up to 30W max.
• IEEE 802.3af and IEEE 802.3at compliant.
Ethernet:
• IEEE 802.3af (15W) and
IEEE 802.3at (30W) compliant.
• Wire type: 4-pair CAT5e and higher.
• Connectivity: RJ45, auto-crossover.
• Speed: 10/100/1000 Mbps.
• Distance: up to 100m.
LED Indicators (Refer to Fig. 1, Pg. 2):
• Yellow and Green LEDs (RJ45 jacks):
IP Link status, 10/100/1000 Base-T/active.
• Green PoE LEDs:
Indicate PoE present.
• Green SFP (Fiber) LED:
Indicates SFP connection.
Environmental:
• Refer to Environmental Conditions on page 3.
Dimensions (W x L x H approx.):
3.375” x 3.8” x 1”
(85.7mm x 96.5mm x 25.4mm).
Installation Instructions:
Unit is powered via 48VDC-56VDC. NetWaySP2P is not intended to be connected to outside plant leads
and should be installed indoors within the protected premises.
1. Mount NetWaySP2P in desired location utilizing the mounting hole (Fig. 1a, pg. 2).
Use a proper fastener and/or wall anchor when securing NetWaySP2P with screw through
its mounting hole to the wall.
2. Connect 48VDC-56VDC power source to terminals marked [48-56VDC –Input +].
Terminals accommodate up to 12 AWG wires. Caution: Make sure to observe polarity.
3. Connect structured cable from port(s) marked [PoE+ Output] on NetWaySP2P to a
PoE device(s) (Fig. 2, pg. 2).
4. Connect fiber optic cable to a fiber SFP module. Connect the module to the port marked
[SFP] on the NetWaySP2P. Connect the other end of fiber cable to an SFP module of a
remote device. SFP LED will illuminate indicating data connection (Fig. 2, pg. 2).
- 2 - NetWaySP2P
Fig. 1
Fig. 1a
Typical Applications:
Fig. 2
Fig. 3
115/230VAC
Input
NetWaySP2P
Converts Ethernet
to Fiber & Provides PoE
Fiber
CAT5e/6
PoE+ (30W) PTZ
CAT5e/6
PoE+ (30W) PTZ
48-56VDC
Input
DC
Power
Supply
NetWaySP2P
2-Port Media Converter/Injector
Input: 48–56VDC
Output: IEEE 802.3at (30W) and
IEEE 802.3af (15.4W)
compliant.
48-56VDC
-- Input + PoE+
Output
PoE+
Output Fiber
SignalSFP
PoE+ (30W) PTZ
115/230VAC
Input
NetWaySP2P
Converts Ethernet
to Fiber & Provides PoE
NetWaySP1
A
Media
Converter/
Repeater
Fiber
CAT5e/6
PoE+ (30W) PTZ
CAT5e/6
CAT5e/6
48-56VDC Input
DC
Power
Supply
NetWaySP1A
Media Converter/Repeater
Input: PoE Class 1 or Higher
Data: 10/100/1000
PoE /
10/100/1000 InPoE
Fiber
Signal
SFP
www.altronix.com
Made in
U.S.A.
NetWay8E
or Midspan/Endspan
NetWaySP2P
2-Port Media Converter/Injector
Input: 48–56VDC
Output: IEEE 802.3at (30W) and
IEEE 802.3af (15.4W)
compliant.
48-56VDC
-- Input + PoE+
Output
PoE+
Output Fiber
SignalSFP
Structured Cables to
PoE Devices
48VDC to
56VDC
Input
-- +
SFP LED
Indicates
data connection
PoE LEDs indicate
PoE present
One (1) Gb
SFP port
for Fiber
NetWaySP2P
2-Port Media Converter/Injector
Input: 48–56VDC
Output: IEEE 802.3at (30W) and
IEEE 802.3af (15.4W)
compliant.
48-56VDC
-- Input + PoE+
Output
PoE+
Output Fiber
SignalSFP
NetWaySP2P - 3 -
Fig. 4
Technical Specifications:
Parameter Description
Ports One (1) 1Gb SFP port.
Two (2) PoE .3af/ .3at Ethernet ports 10/100/1000 Mbps.
Input Power
Requirements 48VDC-56VDC @ 1.2A.
Indicators PoE Green LED: Indicates PoE present.
Fiber Signal Green LED: Indicates SFP connection.
Evironmental
Conditions
Temperature:
Operating (30W): – 40ºC to 70ºC (– 40ºF to 158ºF).
Storage: – 40ºC to 75ºC (– 40ºF to 167ºF).
Relative Humidity: 85% +/–5%.
Operating Altitude: – 304.8 to 2,000m.
Regulatory
Compliance CE European Conformity.
Weights (approx.) Product: 0.25 lb. (0.11 kg) | Shipping: 0.3 lb. (0.14 kg).
PoE+ (30W) PTZ
NetWaySP2P
Converts Ethernet
to Fiber & Provides PoE
CAT5e/6
PoE+ (30W) PTZ
CAT5e/6
Composite
Fiber/Copper
NetWaySP4 Series
NetWaySP2P
2-Port Media Converter/Injector
Input: 48–56VDC
Output: IEEE 802.3at (30W) and
IEEE 802.3af (15.4W)
compliant.
48-56VDC
-- Input + PoE+
Output
PoE+
Output Fiber
SignalSFP
Recommended Altronix SFP Modules:
Altronix P1MM and P1SM10 are hot-pluggable SFP fiber transceiver modules and are readily usable
with all Altronix Spectrum fiber optic equipment for 1Gb transmission rates.
P1MM - For use with Multi-Mode Fiber for distances up to 550m.
P1SM10 - For use with Single-Mode Fiber for distances up to 10km.
- 4 - NetWaySP2P
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
NetWaySP2P K28Q MEMBER
Notes:
Tabla de contenidos
Otros manuales de Convertidor de medios de Altronix
Altronix
Altronix eBridge100RM Manual de usuario
Altronix
Altronix SMP10C12X Series Manual de usuario
Altronix
Altronix NetWaySP1P Manual de usuario
Altronix
Altronix NetWaySP8A Manual de usuario
Altronix
Altronix NetWaySP1BTWP Manual de usuario
Altronix
Altronix Netway Spectrum NetWaySP1A Manual de usuario
Altronix
Altronix NetWay spectrum NetWay SP1P Manual de usuario
Altronix
Altronix NetWaySP8A Manual de usuario
Altronix
Altronix NetWaySP1BT Series Manual de usuario
Altronix
Altronix ebridge100rm Manual de usuario
Altronix
Altronix AL1012X220 Series Manual de usuario
Altronix
Altronix NetWaySP1P Manual de usuario
Altronix
Altronix NetWaySP1A Manual de usuario
Altronix
Altronix NetWaySP8A Manual de usuario
Altronix
Altronix NetWaySP1P Manual de usuario
Altronix
Altronix eBridge PLUS eBridge1PCRMT Manual de usuario
Altronix
Altronix NetWaySP1P Manual de usuario
Altronix
Altronix NetWay3012P Manual de usuario
Altronix
Altronix NetWaySP4PX Manual de usuario
Altronix
Altronix NetWaySP1BT Series Manual de usuario
