Alto Elvis Series Manual de usuario
ELVIS Series
User's Manual
LTO
R
www.altoproaudio.com
Version 1.3 March 2005
English
1
SAFETY INSTRUCTIONS
1. Read Instructions
All the safety and operation instructions should be read before using the product and retain them for future reference.
2. Water & Moisture
This product should not be used near water and will be protect from atmospheric agents in fixed or temporary installations.
3. Heat
This product should be situated away from heat sources such as radiators, or other devices which produce heat.
4. Liquid Entry
Care should be taken so that liquids are not spilled into the product and that objects do not fall on.
5. Service Assistance
This product should be serviced only by qualified service personnel when :
a. Liquids has spilled or objects have fallen into this product, or
b. This product has been exposed to rain, or
c. This product does not appear to operate normally or exhibits change in performance, or been dropped or itshas
cabinet / chassis damaged.
6. Package
The package of this product has been tested, inspect the package before open, if any damage is found, notify to
your dealer.
7. Hearing
This product produce high acoustic levels may cause permanent hearing loss, (SPL in for a defined period of time).
8. Installations
This product should be installed on the wall or in the floor with specific stands, according to the max weight.
"Electric discharge"
This symbol, alert you to the presence of uninsulated dangerous voltage inside the product which constitutes aenclosure,
risk of electric shock.
"Exclamatory point"
This symbol, alert the user to the presence of important operating and maintenance instructions the owner's manualin
included to the product.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TABLE OF CONTENT
4. WIRE CONNECTIONS .........................................................................................................................10
2
1. QUICK START - PASSIVE SPEAKER CABINET....................................................................................3
-. For Passive Full-range Speakers
-. For Passive Subwoofer & Satellite Speakers
2. QUICK START - ACTIVE SPEAKER CABINET.....................................................................................5
-. For Active Full-range Speakers
-. For Active Subwoofer & Satellite Speakers
3. CONNECTION PLATE ................................................................................. ..........................................7
-. PASSIVE FULL-RANGE Speaker for ELVIS10/ELVIS12/ELVIS15/ELVIS12M/ELVIS15M
-. PASSIVE SUBWOOFER Speaker for ELVIS12S/ELVIS15S
-. Active FULL-RANGE Speaker for ELVIS10A/ELVIS12/AELVIS15A/ELVIS12MA/ELVIS15MA
-. Active SUBWOOFER Speaker for ELVIS12SA/ELVIS15SA
5. ELVIS TECHNICAL SPECIFICATIONS.................................................................................................11
-. For Passive Speaker Cabinets
-. For Active Speaker Cabinets
1. QUICK START - PASSIVE SPEAKER CABINET
-. For Passive Full-range Speakers
QUICK START
Elvis Passive Full-range Speakers
3
Stereo
Power Amplifier
speaker cable
Tripod
Mount
Left
Main Mix
Output
Right
Main Mix
Output
Mixer
Tripod
Mount
3). Turn on your mixer first, then the stereo power amplifier.
4). Turn up the volume controls of your amplifier to about 70%.
2). Complete other connections as illustrated.
Make all initial connections with all the equipment powered off, and ensure that all the main volume controls are turned completely
down.
1). Connect one side of the speaker cable to the Output CHA/CHB or Binding Post of your stereo power amplifier
and the other side to the Input socket of your speaker cabinet.
5). Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control to manipulate the output
level.
6). After using, turn off your stereo power amplifier first, then the mixer.
speaker cable
-. For Passive Subwoofer & Satellite Speakers
1). Connect one side of speaker cable to the Output CHA/CHB or Binding Post of your stereo power amplifier and the other
side to the Input socket of your subwoofer, with the second speaker cable connect the Output of the subwoofer to the
Input of satellite.
4
Speaker Cable
pole
Mount
Speaker Cable
pole
Mount
Stereo
Power Amplifier
Left
Main Mix
Output
Right
Main Mix
Output
Mixer
QUICK START
ELVIS Passive Subwoofer & Satellite Speakers
Speaker Cable
Speaker Cable
3). Turn on your mixer first, then the stereo power amplifier.
4). Turn up the volume controls of your amplifier to about 70%.
2). Complete other connections as illustrated.
5). Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control to manipulate the output
level.
6). After using, turn off your stereo power amplifier first, then the mixer.
-. For Active Subwoofer & Satellite Speakers
1). Connect one side of signal cable at your audio mixer in to Output Left /Right (with Stereo-Jack or XLR) and the other
side of the cable in to the Left / Mono Input (COMBO) of the active subwoofer; with the second signal cable connect
the Left Output of the subwoofer (Stereo/Mono-Jack or XLR) to the Line Input (COMBO) of the active satellite (with
Stereo - Jack or XLR).
6
Tripod
Mount
Tripod
Mount
Left
Main Mix
Output
Right
Main Mix
Output
QUICK START
Elvis Active Subwoofer & Satellite Speakers
Signal Cable
Signal Cable
Power Cord
3). Turn on your mixer first, then the active speaker cabinets.
2). Connect the power cord to mains.
5). Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control to manipulate the
output level.
4). Turn up the volume control fo the active speaker cabinets.
6). After using, turn off your active speaker cabinets first, then the mixer.
3. CONNECTION PLATE
- PASSIVE FULL-RANGE Speaker for ELVIS10 / ELVIS12 / ELVIS15 / ELVIS12M/ELVIS15M
(1) INPUT: Receive the power coming from an external power amplifier (SPK +1/-1 connected; +2/-2 not connected).
(2) THRU: Direct LINK for connect in parallel a second speaker cabinet (SPK +1/-1 connected; +2/-2 not connected).
INPUT THRU
LINK
LTO
R
ELVIS 12
SOUND REINFORCEMENT SPEAKER SYSTEM
DESIGNED AND DEVELOPMENT IN ITALY
Power Handling:
AES-180Watts
PEAK - 360 Watts
IMPEDANCE:
8 ohms nominal
SERIAL
MODEL
7
(1) (2)
- PASSIVE SUBWOOFER Speaker for ELVIS12S / ELVIS15S
(1) INPUT: Receive the power (SPK +1/-1 connected;+2/-2 not connected).coming from an external amplifier
(2) OUTPUT: Power output for satellite speaker, under passive crossover filtered at 125Hz (SPK +1/-1 connected;
+2/-2 not connected).
INPUT OUTPUT
LTO
R
ELVIS 12S
DESIGNED AND DEVELOPMENT IN ITALY
POWER HANDLING:
AES-200Watts
PEAK - 400 Watts
IMPEDANCE:
4 ohms nominal
SERIAL
MODEL
(1) (2)
8
-. ACTIVE FULL- RANGE Speaker for ELVIS10A / ELVIS12A / ELVIS15A / ELVIS12MA/ELVIS15MA
(1) Bi-polar main power switch.
(2) Input AC power socket with main fuse.
(3) Ground Swicth.
(4) POWER, blue LED, indicate ON status.
(5) SIGN / COMP, signal/compressor, green/red LED
(6) LINE OUT at + 4dB on XLR connector
(7) LINE IN at + 4dB on COMBO connector.
(8) VOLUME main power amplifier control.
(9) LOW / MID / HIGH, EQ tone control at +/- 6dB.
(10) GAIN control for microphone -10/- 45dB.
(11) MIC IN on balanced XLR, for microphone.
(1)(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
MIC IN
LINE-IN
ON
OFF
AC INPUT: 230V~ 50Hz GND
POWER
MIC GAIN
-10dB -45dB
VOLUME
+4dBu
-
LOW
HIGH
-6dB +6dB
MIDDLE
-6dB +6dB
-6dB +6dB
SIGN
COMP
SERIAL
MODEL
LINE-OUT
PUSH
21
3
NEW TIDE
9
-. ACTIVE SUBWOOFER Speaker for ELVIS12 SA / ELVIS15 SA
(1) Bi-polar main power switch.
(2) Input AC power socket with main fuse.
(3) Ground Swicth.
(4) POWER, blue LED, indicate ON status.
(5) SIGN / COMP, signal/compressor, green/red LED
(6)
(7)
(8) VOLUME main power amplifier control.
(9)
(10)
LEFT signal output on XLR or Jack connector for active satellite, under electronic crossover at 125Hz.
RIGHT on XLR connector for active satellite, under electronic crossover at 125Hz.
RIGHT, input signal on XLR connector.
LEFT/MONO, input signal on COMBO connector.
GND
ON
OFF
AC INPUT: 230V~ 50Hz
RIGHT
LEFT/
MONO
RIGHT
LEFT/
MONO
LINK
OUT
IN
VOLUME
+4dBu
SIGN
COMP
SERIAL
MODEL
POWER
-
(1)(2)
(3)
(4)
(5)
(7)
(6)
(8)
(9)
(10)
Use only with a 250V fuse
PUSH
21
3
NEW TIDE
PUSH
1
3
2
NEW TIDE
Otros manuales para Elvis Series
3
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Oradores de Alto
Alto
Alto MICRO3 Manual de usuario
Alto
Alto OEX600 Manual de usuario
Alto
Alto PS Series Manual de usuario
Alto
Alto TS115 Vibe Manual de usuario
Alto
Alto TS115 truesonic Manual de usuario
Alto
Alto PS4 Manual de usuario
Alto
Alto REVO1 Manual de usuario
Alto
Alto EQU231VU-MKII V2 Manual de usuario
Alto
Alto ELVIS 10 Manual de usuario
Alto
Alto PS 4 LA EVO Manual de usuario
Alto
Alto M Series Monitor Manual de usuario
Alto
Alto MS8 Manual de usuario
Alto
Alto MS8 Manual de usuario
Alto
Alto AMX 180FX-USB Manual de usuario
Alto
Alto TOURMAX SX115 Manual de usuario
Alto
Alto Spectrum PA Manual de usuario
Alto
Alto Elvis Series Manual de usuario
Alto
Alto SR Series Manual de usuario
Alto
Alto OEX-400 Manual de usuario
Alto
Alto TS112W Manual de usuario
