Altec Lansing 4156-8A LF SPEAKER Guía del usuario
4156-8A
High Performance
15” Low Frequency Speaker
FEATURES - THE ALTEC LANSING DIFFERENCE
• High Performance 250W AES / 1,000W Peak Power Handling
• Designed For Direct Radiator Vented Cabinets
• Linear Low Frequency Reproduction
• High Efficiency
GENERAL PRODUCT DESCRIPTION
The 4156-8A is the latest in a 60 year Altec Lansing tradition of
quality loudspeaker components. High power, high efficiency
and linear response make this 15” (381 mm) transducer a very
capable low frequency component for conventional cluster
designs or subwoofers.
Possibly the most celebrated legacy of Altec Lansing is
dependability. The 4156-8A loudspeaker is constructed from a
reinforced corrosion-resistant die-cast frame, a rugged ferrite
magnet structure, and a weather-resistant cone.
The 4156-8A loudspeaker is designed for direct radiator vented
enclosures. An internal enclosure volume of just under 4 cubic
feet (113 liters) is all that is required for the 4156-8A loudspeaker
to provide 3 dB down frequency response to 50 Hz. Installation
of this low frequency loudspeaker is made simple with 0.25 inch
(6 mm) blade type wire terminals on a two position barrier strip,
allowing bare wire leads, solder connections or crimp type quick-
connect wire terminals.
The Altec Lansing model 4156-8A is an excellent component for
custom subwoofers and a perfect complement to our high
frequency compression drivers when the requirements are high
power capability, linear low frequency response, high acoustic
output level, and absolute reliability.
PROFESSIONAl
1000 W. Wilshire Blvd., Suite 362 • Oklahoma City, Oklahoma 73116 • Phone: 1-405-848-3108 • Fax: 1-405-848-3217 • www.altecpro.com
FREQUENCY RESPONSE 1, 2
27 Hz - 3.4 kHz
SENSITIVITY 3
99 dB SPL
POWER HANDLING 4
250 W continuous; 1,000 W peak
MAXIMUM OUTPUT (1 m) 5
123 dB SPL continuous; 129 dB SPL peak
IMPEDANCE 7
Nominal: 8.0 Ohms
Minimum: 6.5 Ohms at 160 Hz
HARMONIC DISTORTION 8
1% rated power 10% rated power
2nd Harmonic 0.57% 2nd Harmonic 2.25%
3rd Harmonic 0.54% 3rd Harmonic 0.94%
THD 0.91% THD 2.49%
INPUT CONNECTIONS
1 x 2 position barrier strip with 0.250 in. blades
DIMENSIONS
Outside Diameter: 15.875 in. (403 mm)
Bolt Circle Diameter: 15.063 in. (383 mm)
Cut-out Diameter
Front Mount: 14.375 in. (365 mm)
Rear Mount: 14.000 in. (356 mm)
Depth: 6.625 in. (168 mm)
WEIGHT
Net: 21 lbs. (9.5 kg)
Shipping: 26 lbs. (11.8 kg)
THEILE-SMALL PARAMETERS:
Re5.6 Ohms
fs29.0 Hz
Qts 0.280
Qms 2.91
Qes 0.310
Vas 353.7 liters (12.49 ft.3)
Sd850.0 cm2(131.75 in.2)
Xmax 4.3 mm (0.17 in.)
Vd365.5 cm3(22.30 in.3)
Le1.05 mH
η02.72%
Bl17.1 Tm
Mms 87.3 g
Cms 350 µm/N
ARCHITECT’S AND ENGINEER’S SPECIFICATIONS
The loudspeaker shall be a multi-purpose 15 inch / 381 mm low
frequency cone driver. The loudspeaker shall have an operating
bandwidth of 27 Hz - 3.4 kHz with a sensitivity of 99 dB when
measured at a distance of one meter. The power handling
capability shall be 250 W AES (1,000 W peak). Nominal
impedance shall be 8 ohms with a minimum impedance of 6.5
ohms at 160 Hz. The nominal free-air resonance shall be 29 Hz.
The dimensions shall be 15.875 inches (403 mm) in diameter by
6.625 inches (168 mm) deep. The loudspeaker shall weigh 21
pounds (9.5 kg). The loudspeaker shall be the Altec Lansing
Professional model 4156-8A.
FREQUENCY RESPONSE IMPEDANCE
As we are continually striving to improve Altec Lansing products, specifications are subject to change without notice.
Please visit www.altecpro.com for the latest information on Altec Lansing Professional products.
1 The frequency response of the loudspeaker is measured at a distance of no less than 3 meters to obtain full range data. The level is then
corrected to be equivalent to a 2.83 V 1 m measurement. A near field measurement of the loudspeaker is performed for frequencies below
500 Hz. This data is then combined with the full range measurement to give an accurate composite frequency response curve.
2 The limits of the frequency response are referenced to -10 dB of the loudspeakers rated sensitivity.
3 The sensitivity of the loudspeaker is the log based average SPL taken over the intended bandwidth of operation for the loudspeaker with a
2.83 V swept sine stimulus. The data is measured and level corrected in a manner consistent with note 1.
4 The power handling capacity of the loudspeaker is tested using AES Standard 2-1984. The test stimulus is band limited (30 Hz – 300 Hz) pink
noise with a 6 dB crest factor. The applied RMS voltage is determined using the minimum impedance of the loudspeaker. The amplifier used
to drive the loudspeaker has a minimum operating headroom of 6 dB referenced to the RMS voltage.
5 The maximum output level of the loudspeaker is calculated based on the sensitivity and the power handling capabilities of the system.
7 The minimum impedance of the loudspeaker is taken over its intended band of operation.
8 The distortion measurements of the loudspeaker are performed at a distance of 1 m with RMS input voltages corresponding to 1% and 10%
of rated power handling calculated using minimum loudspeaker impedance. The distortion percentages are log based averages from 50 Hz –
1 kHz.
VISIT WWW.ALTECPRO.COM FOR
• Authorized EASE data on all Altec Lansing Professional loudspeakers
• Specification sheets in .pdf format. Download page 1 of the specification sheet for you submittals.
• One paragraph A&E Specifications in .doc format
SPECIFICATION NOTES
AW1078 REV02
© 2003 Altec Lansing Professional
1000 W. Wilshire Blvd., Suite 362
Oklahoma City, Oklahoma 73116
Phone: 1-405-848-3108 • Fax: 1-405-848-3217
Web: www.altecpro.com • Email: [email protected]
PROFESSIONAl
Este manual sirve para los siguientes modelos
1
Otros manuales de Oradores de Altec Lansing
Altec Lansing
Altec Lansing RM3010 Manual de usuario
Altec Lansing
Altec Lansing timeMachine IMW465 Manual de usuario
Altec Lansing
Altec Lansing 3182 LF SPEAKER Manual de usuario
Altec Lansing
Altec Lansing iMW725 Manual de usuario
Altec Lansing
Altec Lansing 620 SPEAKER CABINET PLAN Guía del usuario
Altec Lansing
Altec Lansing T612 - QUICK CONNECT CARD Instrucciones de montaje
Altec Lansing
Altec Lansing MINI LIFEJACKET 2 Manual de usuario
Altec Lansing
Altec Lansing 604-8L DUPLEX SPEAKER Guía del usuario
Altec Lansing
Altec Lansing 3156 LF SPEAKER Manual de usuario
Altec Lansing
Altec Lansing EP8 CEILING SPEAKERS Manual de usuario
Altec Lansing
Altec Lansing SHOCKWAVE 100 Manual de usuario
Altec Lansing
Altec Lansing CD408-16T Manual de usuario
Altec Lansing
Altec Lansing DTS642A-F SPEAKER SYSTEM Manual de usuario
Altec Lansing
Altec Lansing LF SPEAKER - RECONE Manual de usuario
Altec Lansing
Altec Lansing IMT7003 Manual de usuario
Altec Lansing
Altec Lansing 109 CEILING SPEAKER Manual de usuario
Altec Lansing
Altec Lansing 409 E CEILING SPEAKERS Manual de usuario
Altec Lansing
Altec Lansing DTS152A-F LF SPEAKER SYSTEM Manual de usuario
Altec Lansing
Altec Lansing DTS645A-F SPEAKER SYSTEM Manual de usuario
Altec Lansing
Altec Lansing Shockwave Manual de usuario
