Altec Lansing LF215-4A LF SPEAKER SYSTEM Manual de usuario
FREQUENCY RESPONSE 1, 2
42 Hz - 650 Hz (±3 dB)
USABLE LOW FREQUENCY LIMIT (-10 dB) 1, 2
33 Hz
SENSITIVITY 3
103 dB SPL, (2.00 V input)
POWER HANDLING 4
500 W continuous; 2,000 W peak
MAXIMUM OUTPUT (1 m) 5
130 dB SPL continuous; 136 dB SPL peak
TRANSDUCER COMPONENTS
2x 15 in. Woofers (4156-8A)
IMPEDANCE 7
Nominal: 4.0 Ω
Minimum: 3.5 Ωat 41 Hz
HARMONIC DISTORTION 8
1% rated power
2nd Harmonic 0.30%
3rd Harmonic 0.40%
THD 0.63%
10% rated power
2nd Harmonic 1.38%
3rd Harmonic 0.49%
THD 1.54%
INPUT CONNECTIONS
2x 4 position barrier strip and 2x NL4
CONTROLS
Drivers in Parallel or Split Mode switch
ENCLOSURE MATERIALS & FINISH
18 mm, 13 ply Birch Plywood Finished with Charcoal
Grey or White Catalyzed Polyurethane
SUSPENSION SYSTEM 9
Working Load Limit (maximum weight applied to
uppermost mounting point): tbd lbs. (tbd kg)
(12) 3/8 in.-16 Threaded Mounting Suspension Points
(3 each top & bottom and 2 each sides & back)
DIMENSIONS
37.50 in. (H) x 24.13 in. (W) x 26.13 in. (D)
x 10.13 in. (W rear)
953 mm (H) x 613 mm (W) x 664 mm (D)
x 257 mm (W rear)
WEIGHT
Net 115 lbs. (52.3 kg)
Shipping 138 lbs. (62.7 kg)
LF215-4A
FEATURES - THE ALTEC LANSING DIFFERENCE
• Dual 15” / 380mm Low Frequency Speaker
•High Performance 500 W AES / 2,000 W Peak Power Handling
• Excellent Broadband Efficiency – 103 dB SPL, 1 W 1 m
• Matching Footprint To Altec’s DE6412 & DE9412
• Strong 13-Ply Birch Paintable Cabinet
• Steel Reinforced Suspension Points
• Forged Eyebolt Suspension Kit Included
• Available in Charcoal Gray or White Finishes
GENERAL PRODUCT DESCRIPTION
The LF215-4A is a dual 15” / 380mm subwoofer with the same
footprint as the Altec Lansing DE6412 and DE9412 Duplex®
full-range speaker systems. In addition to its use with Altec’s DE
& DS-series full-range speaker systems, the LF215-4A can be easily
incorporated into component-based sound systems. The
LF215-4A has been designed to provide extended low frequency
performance in Auditoriums, Performing Arts Centers, Houses
of Worship, or any facility requiring low frequency reinforcement
for full-range music reproduction.
Two of the Altec model 4156-8A 15” / 380mm woofers
are used in the LF215-4A. The drivers may be connected in
parallel (for a single four ohm load) or driven individually (for
two, eight ohm loads) via a switch and separate driver inputs.
This robust component has been designed to deliver tight,
punchy low frequency reproduction in vented speaker cabinets.
The 4156-8A has a corrosion resistant die-cast frame and
moisture-resistant cone for maximum durability in all
environments.
The 13-ply birch plywood enclosure is paintable, and features
steel reinforced suspension points. Altec Lansing includes a
forged eyebolt suspension kit with each subwoofer. Input
connections are via barrier strip or Neutrik®Speakon®connectors.
The LF215-4A is offered in either charcoal grey or white, with
contrasting cloth covered metal grille. Altec Lansing includes
neutral grille cloth with each subwoofer, allowing you to dye the
cloth to integrate the subwoofer into the surroundings.
The LF215-4A is designed to work in conjunction with Altec’s
DE6412 and DE9412 Duplex®12”/300mm full-range speaker
systems. Presets are available for the Altec Lansing 4048A
4-in x 8-out DSP Processor, allowing the system designer to easily
incorporate the LF215-4A into multi-channel applications.
PROFESSIONAl
1000 W. Wilshire Blvd., Suite 362 • Oklahoma City, Oklahoma 73116 • Phone: 1-405-848-3108 • Fax: 1-405-848-3217 • www.altecpro.com
ARCHITECTS & ENGINEERS SPECIFICATION
The loudspeaker system shall be a low frequency, multi-
purpose trapezoid enclosure consisting of two 15-inch /
380mm cast frame loudspeaker components with moisture-
resistant cones. The loudspeaker system shall have an
operating bandwidth of 42 Hz - 650 Hz with a sensitivity
of 103 dB when measured at a distance of one meter. The
power handling capability shall be 500 W AES (2,000 W
peak). Nominal impedance shall be 4.0 ohms with a
minimum impedance of 3.5 ohms at 41 Hz. The unit shall
be a trapezoid enclosure constructed of 18 mm
birch plywood with a cloth covered metal grille. The
cabinet shall include integral steel-reinforced suspension
points. Forged shoulder machinery eye bolts shall be
included to facilitate the suspension of the speaker system.
The dimensions shall be 37.50 inches (953 mm) high by
24.13 inches (613 mm) wide by 26.13 inches (664 mm)
deep. The loudspeaker system shall weigh 115 pounds
(52.3 kg). The loudspeaker system shall be the Altec
Lansing Professional model LF215-4A.
As we are continually striving to improve Altec Lansing products, specifications are subject to change without notice.
Please visit www.altecpro.com for the lastest information on Altec Lansing Professional products.
Altec Lansing Professional
Oklahoma City, OK 73116
A division of Altec Lansing Technologies, Inc., Milford, PA 18337-0277 • Made in China
LF215-4A
++
PIN 1 +
PIN 1 -
INPUT
PARALLEL MODE
4 OHMS
SPLIT MODE
2x 8 OHMS
PARALLEL MODE
TOP DRIVER
SPLIT MODE
PIN 2 +
PIN 2 -
BOTTOM
DRIVER
SPLIT MODE --
++
--
PARALLEL MODE
TOP DRIVER
SPLIT MODE
BOTTOM
DRIVER
SPLIT MODE
PARALLEL
SPLIT
MODE
AW1139 REV01
© 2003 Altec Lansing Professional
1000 W. Wilshire Blvd., Suite 362
Oklahoma City, Oklahoma 73116
Phone: 1-405-848-3108 • Fax: 1-405-848-3217
Web: www.altecpro.com • Email: [email protected]
PROFESSIONAl
15
11.9 [301.51] 9.47 [240.47]
5.1 [128.33]
DIMENSIONS ARE IN INCHES.
DIMENSIONS SHOWN IN ( ) PARENTHESES ARE IN MILLIMETERS.
DENOTES CENTER OF MASS
1.7 [43.40]
6.33 [160.76]
6.65 [169.01]
24.1 [612.10]
37.40 [950.00]
26.10 [663.05]
1.71 [43.40]
9.47 [240.47]
16.19 [411.26]
18.70 [475.02]
26.11 [663.28] 16.64 [422.71]
10.10 [256.65]
7.56 [192.14]
MOUNTING DIMENSIONS
SPECIFICATION NOTES
1 The frequency response of the loudspeaker system is measured at a distance of no less than 3 meters to obtain full range data. The level is
then corrected to be equivalent to a 2.0 V 1 m measurement. A near field measurement of the loudspeaker system is performed for
frequencies below 500 Hz. This data is then combined with the full range measurement to give an accurate composite frequency response
curve.
2 The limits of the frequency response are referenced to -3 dB of the systems rated sensitivity.
3 The sensitivity of the loudspeaker system is the log based average SPL taken over the intended bandwidth of operation for the system with a
2.0 V swept sine stimulus. The data is measured and level corrected in a manner consistent with note 1.
4 The power handling capacity of the loudspeaker system is tested using a full range form of AES Standard 2-1984. The test stimulus is band
limited (30 Hz – 300 Hz) pink noise with a 6 dB crest factor. The applied RMS voltage is determined using the minimum impedance of the
system. The amplifier used to drive the system has a minimum operating headroom of 6 dB referenced to the RMS voltage.
5 The maximum output level of the loudspeaker system is calculated based on the sensitivity and the power handling capabilities of the
system.
7 The minimum impedance of the loudspeaker system is taken over its intended band of operation.
8 The distortion measurements of the loudspeaker system are performed at a distance of 1 m with RMS input voltages corresponding to 1%
and 10% of rated system power handling calculated using minimum system impedance. The distortion percentages are log based averages
from 30 Hz – 300 Hz.
9 Before attempting to suspend the loudspeaker system, consult a certified structural engineer. This loudspeaker system can fall from
improper suspension, resulting in serious injury and property damage. Maximum enclosure rigging angle is 45°. Use only the correct mating
hardware, forged shoulder machinery eye bolt, Mil Spec MIL 51937-3. All associated rigging is the responsibility of others.
VISIT WWW.ALTECPRO.COM FOR
• Authorized EASE®data on Altec Lansing Professional speakers.
• Specification sheets in .pdf format. Download page 1 of the specification sheet for your submittals.
• One paragraph A & E Specifications in .doc format.
Otros manuales de Sistema de altavoces de Altec Lansing
Altec Lansing
Altec Lansing 9844-8B SPEAKER SYSTEM Manual de usuario
Altec Lansing
Altec Lansing DTS200 SPEAKER SYSTEM Manual de usuario
Altec Lansing
Altec Lansing VS-4121 Manual de usuario
Altec Lansing
Altec Lansing VS2321 Manual de lista de piezas
Altec Lansing
Altec Lansing Duplex DTS200PI Manual de usuario
Altec Lansing
Altec Lansing BXR1220 Manual de usuario
Altec Lansing
Altec Lansing 220 Manual de usuario
Altec Lansing
Altec Lansing PS-360A SPEAKER SYSTEM Manual de usuario
Altec Lansing
Altec Lansing VS3251 Manual de usuario
Altec Lansing
Altec Lansing Moondance Glow M402SR Manual de usuario
Altec Lansing
Altec Lansing VS2421 Manual de usuario
Altec Lansing
Altec Lansing VS-4121 Manual de instrucciones
Altec Lansing
Altec Lansing 925-8B CEILING SPEAKER Manual de usuario
Altec Lansing
Altec Lansing 9880-8A LF SPEAKER SYSTEM Manual de usuario
Altec Lansing
Altec Lansing M202 Manual de usuario
Altec Lansing
Altec Lansing DTS-640 Manual de usuario
Altec Lansing
Altec Lansing EXPRESSIONIST CLASSIC Manual de usuario
Altec Lansing
Altec Lansing 251 Manual de usuario
Altec Lansing
Altec Lansing THX MX5021 Manual de usuario
Altec Lansing
Altec Lansing VS2220 Manual de usuario
Manuales populares de Sistema de altavoces de otras marcas
Sondpex
Sondpex Active Speaker System and Digital Music... Manual de usuario
JVC
JVC NX-PN7 Manual de usuario
Marshall Amplification
Marshall Amplification AR-DM61-BT Manual de usuario
Yamaha
Yamaha NX-A01 - Speaker Sys Manual de usuario
SE Audiotechnik
SE Audiotechnik I-LINE Manual de usuario
Gemini
Gemini WRX-843 Series Manual de usuario