ALORAIR STORM PRO Manual de usuario

Specifications subject to change without notice.

STORM PRO DEHUMIDIFIER

INSTALLATION AND OPERATIONS MANUAL

- READ AND SAVE THESE INSTRUCTIONS -

Patent Pending

Tel: 1-888-990-7469 E-mail:sales@alorair.com

Add: 4240 Latham Street, Suite D, Riverside, CA 92501

AlorairSolutionsINC.

Safety Notes

The Storm Pro dehumidifier must always be connected using a grounded electrical

connection as required for all electrical appliances. The warranty is voided and all respon-

sibility for the operation transfers to the owner if non-grounded wiring is utilized.

Your Storm Series dehumidifier must be maintained and serviced by qualified technicians.

Storm dehumidifiers are intended for use only when the unit is installed in a level and

upright position. Operating the unit in any other position could cause water to come in

contact with the electrical components.

Before moving the dehumidifier, turn off the unit and allow the pump reservoir to empty (if

unit is already o ff, press "P" button to confirm drain reservoir is empty). After the pump has

finished operation, unplug the power cord and relocate the unit to the desired position.

If the inside of the machine has gotten wet for any reason, the unit should be opened and

allowed to dry thoroughly before reconnecting it to electric and restarting.

For proper operation, neither the inlet or discharge should be positioned against a wall. A

minimum of 8" clearance between the Storm and any obstruction is required.

Do not insert any objects or fingers into the inlet or discharge.

All work on the machine should be done with the unit off and unplugged.

Do not spray water or cleaner directly on the exterior of the Elite. Only use a damp cloth

to clean the exterior and always unplug the unit first.

Do not use unit as shelf or device to hang clothes as this could cause damage to unit.

Do not stand on the machine.

Table of Contents

Introduction.....................................................................................

..................................................................................

.......................................................................

.................................................................

.......................................................................

..................................................................

...............................................................................

.........................................................................................

.........................................................................

...............................................................................

Unit Overview

LCD Display Introduction

Preparing the Unit for Use

Maintenance & Repair

Storing Your Dehumidifier

Troubleshooting

Warranty

Readiness Checklist

Service Checlist

Alorair Solutions:1-888-990-7469

sales@alorair.com

Introduction

Identification

Congratulations on purchasing a Storm Pro dehumidifier! The Storm Pro comes

with an extensive warranty plan. To ensure you are eligible, be sure to note the serial

number and date of purchase. The serial number can be found on the data on the

back of the unit.

Model Name: Storm Pro

Serial Number:

Date of Purchase:

Customer Service

For additional questions concerning the operation fo your dehumidifier, please

Contact your installing contractor

Contact

Features

Built-in Pump with Overflow Protection

85 Pints Per Day

High COP: 2.85 L/kWh

Only 53 dBa

Automatic humidistat

Self Monitoring System

Eco Friendly R410A Refrigerant

Easy Access to Internal Components

Auto Restart After a Power Outage

Unit Can Be Ducted on the Supply/Outlet, If Necessary

240

How Your Storm Dehumidifier Works

The Storm Pro dehumidifier utilizes its integral humidistat to monitor the conditioned space.

Once conditions are outside the desired setpoint, the compressor energizes and air is

drawn across an evaporator coil. The evaporator coil is cooler than the dew point of the air

so water vapor will turns into liquid condensation. The air is then reheated through the

condenser coil and distributed back into the room.

Electrical Supply

WARNING Volts may cause serious injury from electric shock.

Power Supply:

Outlet Requirement:

Circuit Protector:

115V, 60 Hz AC Only 1 Phase

3-Prong, GFI

15 Amp Time D elay F use o r Circuit Breaker

1. Disconnect electrical power before servicing 3. Do not use an extension cord

2. Only plug unit into grounded electrical outlet 4. Do not use a plug adapter

WARNING

Installation

Place the Pro in your desired location. The inlet of the machine should be at least 8"

from any obstructions. If the unit has been transported in a horizontal position, allow it to

sit in an upright position for at least 30 minutes before operating

Do not use dehumidifier in an environment where corrosive or high VOC materials are applied.

Unit Overview

Front View

Rear View

Air Inlet

Air Filter

Handle

Access Latch

Wheel

Front Cover

Air Outlet

Drain Tube

Connection

LCD Display

Tubing &

Cord Rack

Power Cord

LCD Display Instructions

1. When the machine is powered on but not working:

Boot display: The LOGO interface

will disappear after 2 seconds. Enter

the following interface

The machine displays when it is not

working. (Power off state but have

electricity)

2. Main interface display of dehumidification state:

The following information is displayed when the machine is working:

Refers to the working time, which is defined as the time from

starting up to shutting down,including the defrost time during

the period, and the standby time after the humidity. The

submenu has a reset function. If not, the working time shall

be accumulated.

Total time 9999 hours, the largest cumulative to the largest

automatically reset after restart, and display units for hours.

(round off).

000 JOB HRS:

(after power on, the buzzer makes a sound)

PURGE

000 LIFE HRS:

Refers to the total working time, i.e. the total working time (hours), which is in hours.(press the mode key +

select the confirmation key, and the total working time will be cleaned after 3 seconds.

IN/OUT 00℉ 00% 00 gr / lb:

Indicates the temperature, humidity and moisture content of the air inlet and outlet

{GPP - grain per pound (gr/lb)}.

Indicates set humidity.

Set 00%:

If the main interface does not operate for 10 minutes, the screen will go out.Press any key to

wake up.

Other icons light up or flicker when opened

The total working time is the accumulation of each working time (hours) in hours. (Press the

mode key + select to confirmation key, and the total working time will be cleaned after 3 seconds.

3.Dehumidification status submenu interface display

3.1

Device name displayed on the screen:

You can change the device name on the APP

application

BTID=Unique identifier for Hotspot broadcasting

“Indicates”:Do I need to clear out this time?",

press ">"if you need to clear. When the operation

is completed, the working time of the main

interface and the working time of this interface

will be reset and started to be instant again.

After accumulation (9999), clean up and round.

3.2

3.3

“Coil Temp 000℃ ”: Used to display the current

temperature of the coil.When it is below zero,

the "-" symbol is displayed in front. "-" is not

required on zero.

3.4

Wifi hotspot: factory setting is "0FF",

press > to enable wifi hotspot and switch

ON/OFF.The device can transmit data and receive

APP commands.The icon flickers when connected

on the main interface. After successful connection,

the icon displays normally.

3.5.1

The power down time is adjusted according to">"

and the power down time increases from 3 to 20

minutes (3-5-10-15-20), which is the so-called

stop time of the fan after shutdown, in order to

better drain the water.Factory set for 3 minutes.

(the other state of the fan is still 15 seconds.)

3.5.2

The screen displays when you press shut

down:

Indicates: the fan is closed after a few minutes,

and the standby page UNIT OFF is displayed after

the fan is closed.

3.6 3.7

“Temp Units ℉/℃”：Used for temperature scale

switching.Press the ">" button to switch ℉/℃,

after switch symbol of corresponding parts is also

changing.

“MOISTURE CONTENT UNITS”：It is used to

switch the unit of GPP value with moisture

content. Press > to switch the Ib or Kg, after

switch symbol of corresponding parts is also

changing.

3.8

"Humidistat Setpoint 00%":Used for setting dehumidification

mode humidity.Press ">" to set the humidity. The adjustment

range of humidity setting is between 25 and 80%.

Each key rises or falls 5%, which can be recycled.

When the setting is completed,do not operate for 5 seconds

and begin to take effect.(Otherwise, the compressor will be

shut down immediately after it is below ambient humidity at

the time of setting.) Humidity below 25 percents "CO" mode

recyclable.The main interface displays the set parameters.

4. Main interface frosting status display:

The machine will display this after defrost when running

When the machine is running normally, “Deffrost

SHUTDOWN IN 06:00” will occurs in the

interface after defrosting. It’s defrost countdown

use seconds as units. This screen displays only

3 seconds. Displays the previous interface and

status after restoration.If it is the home screen,

the frost icon will flash.

When the user is operating in the submenu, the

machine is in the frosting state.At this point, the

frosting interface displays 3 seconds, and returns

to the submenu program in the background

countdown.When the user returns to the main

interface without any operation, the frosting state

is displayed inthe main interface in the way of

icon flicker.

5. Compressor on waiting interface display

Compressor protection time not shown:

“Compressor ready IN 03:00” indicates : That the

interface will be displayed when the compression is

in a protected state. (including power-on and shutdown,

the humidity rises immediately after the arrival of L0

HI, and the shutdown resumesimmediately after the

emergence of L0 HI).Displays the countdown in seconds.If the

above situation does not occur within 3 minutes, it is not

shown.

Otros manuales para STORM PRO

Tabla de contenidos

Otros manuales de Deshumidificador de ALORAIR

ALORAIR

ALORAIR ARMORED 170L Manual de usuario

ALORAIR

ALORAIR Sentinel HDi120 Manual de usuario

ALORAIR

ALORAIR Sentinel SLGR 1400X Manual de usuario

ALORAIR

ALORAIR Sentinel HDi90 Manual de usuario

ALORAIR

ALORAIR Storm LGR Extreme Manual de usuario

ALORAIR

ALORAIR Storm Elite Manual de usuario

ALORAIR

ALORAIR STORM PRO Manual de usuario

ALORAIR

ALORAIR Sentinel HDi120 Manual de usuario

ALORAIR

ALORAIR Storm LGR Extreme Manual de usuario

ALORAIR

ALORAIR Storm SLGR 1600X Manual de usuario

ALORAIR

ALORAIR Sentinel HDi100 Manual de usuario

ALORAIR

ALORAIR Sentinel HS35 Manual de usuario

ALORAIR

ALORAIR Sentinel SLGR 1400X Manual de usuario

ALORAIR

ALORAIR Storm Elite Manual de usuario

ALORAIR

ALORAIR Sentinel HDi90 Manual de usuario

ALORAIR

ALORAIR Sentinel HD90 Manual de usuario

ALORAIR

ALORAIR Storm SLGR 850C Manual de usuario

Manuales populares de Deshumidificador de otras marcas

Daitsu

Daitsu CD031IU-DFA Manual de usuario

Fehom

Fehom PDGT701BE Manual de usuario

Hitachi

Hitachi RD-190GX Manual de usuario

Westpoint

Westpoint MDF1-30AE Manual de usuario

SOLIS

SOLIS easy dry compact Manual de usuario

ENVIROBOSS

ENVIROBOSS EB240 Manual de usuario

Sinclair

Sinclair R-9112 Manual de usuario

Kenmore

Kenmore 580.54701 Manual de usuario

Demargo

Demargo DM828NF Manual de usuario

Altrad Lescha

Altrad Lescha LDH 600 Manual de usuario

BOMANN

BOMANN LE 1150 CB Manual de usuario

SPT

SPT SD-46 Manual de usuario

REMKO

REMKO SLN 40 Manual de usuario

Haier

Haier HD458 Manual de usuario

Logik

Logik L20DHW12 Manual de usuario

Frigidaire

Frigidaire FDR30S1 - 30 Pint Capacity Dehumidifier Guía de inicio rápido

Blitz

Blitz HHD Series Manual de usuario

Prem-I-Air

Prem-I-Air PD14DEN Manual de usuario