Alliance Laundry Systems ATE50FWP431AW01 Manual de usuario

www.comlaundry.com

Troubleshooting

Part No. 802848R2

August 2011

Homestyle

Stacked Washer/

Dryers

Refer to Page 6 for Model Numbers

SWD452C

the expressed written consent of the publisher.

802848 1

Table of

Contents

Section 1 – Safety Information ...............................................................3

Locating an Authorized Servicer...........................................................4

Section 2 – Introduction ..........................................................................5

Customer Service...................................................................................5

Nameplate Location...............................................................................5

Model Identification ..............................................................................6

How Your Stacked Washer/Dryer Works .............................................7

Section 3 – Troubleshooting....................................................................9

1. Washer Motor Circuit ...................................................................9

2. Troubleshooting Knocking Noise .................................................9

3. No Spin Due to Out-of-Balance Switch Wiring Problem

Starting Serial Nos. Beginning 0307...........................................10

4. Troubleshooting LEDs on Washer Inverter Controls Starting

Machine Serial No. 0911014603 ................................................11

5. No Spin (Washer)........................................................................11

6. Troubleshooting Shock Absorbers..............................................13

Section 4 – Dryer Troubleshooting ......................................................15

7. Dryer Motor Does Not Run ........................................................16

8. Dryer Stops in Cycle; Quits After the First Few Loads;

Has a Burning Smell; Cycles On Motor Thermal Protector .......18

9. Dryer Motor Runs But Cylinder Does Not Turn ........................19

10. Dryer Motor Does Not Stop .......................................................20

11. Dryer Runs Only When Door is Open........................................21

12. Dryer Heating Assembly Does Not Heat or

Burner Does Not Ignite ...............................................................22

13. Igniter Does Not Glow (Gas Supply Sufficient) –

Gas Dryer Models .......................................................................24

14. Burner Ignites and Goes Out Repeatedly –

Gas Dryer Models .......................................................................25

15. Igniter Glows But Burner Does Not Ignite –

Gas Dryer Models .......................................................................26

16. Dryer Heater Assembly or Burner Shuts Off Prematurely .........27

17. Dryer Heater Assembly or Burner Repeatedly

Cycles Off On Limit Thermostat ................................................28

18. Dryer Heater Assembly or Burner Does Not Shut Off ...............30

19. Clothes Do Not Dry in Dryer......................................................31

20. Timer Does Not Advance in Automatic Cycle ...........................32

21. Clothes Are Too Hot When Removed From Dryer ....................33

22. Excessive Chattering or Vibrating Noise in Dryer .....................34

23. Excessive Humming or Whistling Noise in Dryer......................35

Section 5 – Washer Control Troubleshooting.....................................37

24. Washer Error Code Listing .........................................................37

25. Washer Will Not Start – No LEDs/Lights Lit

(No response to start switch).......................................................38

2802848

26. Washer Will Not Start – Door Open Error

(Wash/Rinse LEDs Flashing –

Door must be closed and attempting to lock) .............................40

27. Washer Will Not Start – No Door Lock

(Door LED Flashing) ..................................................................42

28. Washer Motor Will Not Run

(Door/Final Spin LEDs Flashing) ...............................................44

29. Washer Will Not Fill – No Communication Error

(Wash/Door LEDs Flashing) ......................................................46

30. Washer Overflows.......................................................................48

31. Pump Does Not Operate .............................................................50

32. Serial Communication Error

(Final Spin/Rinse LEDs Flashing) ..............................................52

33. Washer Will Not Heat – Open/Shorted Temperature Sensor

(Heating LED Flashing at End of Cycle)

(Models equipped with heater) ...................................................54

34. Washer Will Not Heat (Models equipped with heater)...............56

Section 6 – Adjustments ........................................................................59

35. Cabinet Leveling Legs ................................................................59

36. Washer Loading Door.................................................................60

37. Washer Motor Belt Tension........................................................61

38. Washer Door Catch.....................................................................62

39. Shipping Braces ..........................................................................64

40. Burner Flame (Gas Models)........................................................65

Section 7 – Dryer Test Procedures .......................................................67

41. Timer Contacts............................................................................67

42. Fabric Selector Switch ................................................................68

43. Drive Motor.................................................................................69

44. Motor Switch...............................................................................72

45. Burner System Operation............................................................74

46. Electrical Circuit To Ignition System (Gas Models) ..................75

47. Gas Valve Coils Check (Gas Models) ........................................75

48. Sensor Check (Gas Models)........................................................76

49. Igniter Check (Gas Models)........................................................76

50. Thermal Fuse (Electric Models) .................................................77

51. Heater Assembly (Electric Models)............................................77

52. Cycling or Limit Thermostat.......................................................77

53. Door Switch ................................................................................78

Section 8 – Internal Wiring of Dryer Motor Switch...........................79

802848 3

Section 1

Safety Information

Throughout this manual and on machine decals, you will find precautionary statements (“CAUTION,”

“WARNING” and “DANGER”) followed by specific instructions. These precautions are intended for the personal

safety of the operator, user, servicer, and those maintaining the machine.

aDANGER

Danger indicates an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.

WARNING

Warning indicates a hazardous situation that, if not avoided, could cause severe personal injury or death.

CAUTION

Caution indicates a hazardous situation that, if not avoided, may cause minor or moderate personal injury or property

damage.

Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions.

IMPORTANT

The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will

occur if the procedure is not followed.

NOTE

The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is

important but not hazard related.

In the interest of safety, some general precautions relating to the operation of this machine follow.

• Failure to install, maintain, and/or operate this machine according to the manufacturer’s

instructions may result in conditions which can produce serious injury, death and/or property

damage.

• Do not repair or replace any part of the machine or attempt any servicing unless specifically

recommended or published in this Service Manual and that you understand and have the

skills to carry out.

• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the machine is properly grounded and to reduce the risk of fire,

electric shock, serious injury, or death.

W284

WARNING

4802848

Safety Information

NOTE: The WARNINGS and IMPORTANT INSTRUCTIONS appearing in this manual are not meant to

cover all possible conditions and situations that may occur. Common sense, caution and care must be

exercised when installing, maintaining or operating the machine.

Always contact your dealer, distributor, service agent or the manufacturer about any problems or conditions you do

not understand.

Locating an Authorized Servicer

Alliance Laundry Systems is not responsible for personal injury or property damage resulting from improper

service. Review all service information before beginning repairs.

Warranty service must be performed by an authorized technician, using authorized factory parts. If service is

required after the warranty expires, Alliance Laundry Systems also recommends contacting an authorized technician

and using authorized factory parts.

To reduce the risk of electric shock, fire, explosion, serious injury or death:

• Disconnect all electric power to the machine and accessories before servicing.

• Close gas shut-off valve to gas dryer before servicing.

• Never start machine with any guards/panels removed.

• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the machine is properly grounded.

• Washer motor not grounded! Disconnect electric power before servicing motor.

W502

WARNING

Repairs that are made to your products by unqualified persons can result in hazards due to

improper assembly or adjustments subjecting you or the inexperienced person making such

repairs to the risk of serious injury, electrical shock or death.

W007

WARNING

If you or an unqualified person perform service on your machine, you must assume the

responsibility for any personal injury or property damage which may result. The manufacturer

will not be responsible for any injury or property damage arising from improper service and/or

service procedures.

W286

WARNING

802848 5

Section 2

Introduction

Customer Service

If literature or replacement parts are required, contact

the source from whom the machine was purchased or

contact Alliance Laundry Systems at (920) 748-3950

for the name and address of the nearest authorized

parts distributor.

For technical assistance, call either of the numbers

listed below:

(920) 748-3121 Ripon, Wisconsin

+32 56 41 20 54 Wevelgem, Belgium

Nameplate Location

When calling or writing about your product, be sure to

mention model and serial numbers. Model and serial

numbers are located on nameplate(s) as shown.

SWD1199P

Nameplate

6802848

Introduction

Model Identification

Information in this manual is applicable to these washers.

ATE50FWP431AW01 LTSA7A*N3300

ATG50FWP301AW01 LTSA7A*N4350

BTE50FSP171TW01 LTSA9A*N

BTE50FSP281CW01 LTSA9A*N1180

BTG50FSP091CW01 LTSA9A*N3000

BTG50FSP111TW01 LTSA9A*N3060

FTE50FSP301NW01 LTUA7A*N

LTE50FGP541NW23 LTUA7A*N2802

LTKA6A*N4350 LTUA9A*N

LTL50FGP541NW23 LTZA7A*N

LTSA7A*N LTZA7A*N2802

LTSA7A*N1500 LTZA9A*N

LTSA7A*N2989 LTZA9A*N0902

LTSA7A*N3000

* Add Letter To Designate Color. W – White Q – Bisque

802848 7

Introduction

How Your Stacked Washer/Dryer Works

SWD828N

Pressure Switch

(Located inside

control cabinet)

Control

(Located inside

control cabinet)

Electric

Drain Pump Motor

Outer

Tub

Inner

Basket

Mixing

Valve

Exhaust Fan

Inverter Control

(Mounted to base

of washer)

Motor

Cylinder

Air Duct

Lint

Filter

Heating Element

(Electric Models)

8802848

General (Dryer)

The dryer uses heated air to dry loads of laundry.

When the motor is started, the exhaust fan pulls fresh

air in through louvers at the rear of the dryer and over

the heat source (burner flame for gas and heating

element for electric). The heated air moves through the

heater duct and into the cylinder, where it circulates

through the wet load. The air then passes through the

lint filter, air duct and exhaust fan, where it is vented to

the outdoors.

General (Washer)

This frontload washer provides some of the same

principles of operation as the typical topload washers.

It senses water level, it dispenses the desired laundry

detergent, agitates the clothes for good cleaning

action, removes the water out of the washer and spins

the clothing in preparation for the dryer.

The difference in operation is primarily the rotational

washing agitation created for the horizontal basket and

drum. This agitation tumbles the clothes in a

clockwise, pause, and counter-clockwise direction.

This reversing tumbling action provides an efficient

washing process and requires less laundry detergent

and less water.

The cycle begins by pressing the start button, which

locks the loading door. The type of cycle and water

temperature are determined by the cycle select switch

and temperature selector switch.

The inner basket starts agitating during the wash water

fill. A column of air is trapped in a pressure bulb and

hose. The air pressure continues to increase as the

inner basket fills with water until it is great enough to

activate the pressure switch which then causes the

wash fill to stop.

The regular and perm press agitate cycles tumble the

clothing in a clockwise direction for a period of 15

seconds, pauses for nine seconds and then tumbles the

clothing in a counterclockwise direction for 15

seconds. This agitation continues until the wash cycle.

The machine stops agitating and turns on the pump

which removes the wash water.

Upon completion of the wash cycle, the machine goes

into two rinse cycles. Fresh cold water is brought into

the inner basket via the mixing valve until the pressure

switch shuts off the water while agitating. The rinse

cycle consists of agitation for a predetermined amount

of time then a spin mode with the pump running while

the machine goes into a series of 4 short 500 RPM

spins.

After all the rinse cycles have been completed, the

washer goes into a final high spin cycle to extract as

much water as possible from the clothing to prepare

them for the dryer. The spin speeds and duration of

this final high spin cycle are determined by the type of

wash cycle selected (refer toTable 1 or Table 2).

NOTE: Washer may not reach 1000 RPM because

of an out-of-balance condition. Control may limit

speed to 850, 650 or 500 RPM depending on severity

of out-of-balance condition.

Technical (Washer)

The basic operational system of this washer consists of

the control, temperature switch, the inverter control,

pressure switch, water valves, electric pump, A.C.

motor and cycle select switch.

The control performs all timing functions like the

timer in a topload washer.

The inverter control uses a speed sensor on the motor

to measure the drum RPM. Before entering any spin

step the inverter control measures the RPM of motor to

sense out-of-balance. The inverter control will try to

redistribute the clothes if an out-of-balance condition

exists; the inverter control will limit the spin speed to

several speeds depending on the severity of the out-of-

balance condition. If the out-of-balance condition is

severe enough the inverter control will limit speed to

90 RPM and will not spin.

NOTE: An additional out-of-balance switch is used

to detect any out-of-balance condition during spins.

If this switch opens during a spin step, the inverter

control immediately stops and then restarts the

spin.

Models Through Serial No. 0911014602

Regular Perm Press Delicate

650

RPM

minutes

1000

RPM

minutes

Table 1

Models Starting Serial No. 0911014603

Regular Perm Press Delicate

500

RPM

minutes

650

RPM

minutes

1000

RPM

minutes

Table 2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Arandela de Alliance Laundry Systems

Alliance Laundry Systems

Alliance Laundry Systems EA2011*A3000 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems Topload Washer Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems CCN020HNF Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems NetMaster HC18NC2 Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems Commercial Automatic Washer Manual de uso y mantenimiento

Alliance Laundry Systems

Alliance Laundry Systems HWNLX2SP111CW01 Instrucciones de funcionamiento

Alliance Laundry Systems

Alliance Laundry Systems Hardmount Coin and OPL Manual de instalación y operación

Alliance Laundry Systems

Alliance Laundry Systems Cabinet Hardmount SC27SN Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems 800532R3 Guía

Alliance Laundry Systems

Alliance Laundry Systems UW35PV Series Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems AWN311SP111TW01 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen TV2000WN Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems PHM1263R Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems LTS80A Series Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems LWS16A series Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems LWK23A*-3050 series Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems 38903R6 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems HWF261*E Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems HWF261*E Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems HCD020GD2 Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems H370I Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems UW POCKET HARDMOUNT UW35B2 Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems 802749r1 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems LWS02A series Manual de usuario

Manuales populares de Arandela de otras marcas

Tricity Bendix

Tricity Bendix AW 1000 W Guía del producto

Panasonic

Panasonic NA-F60L5WRB Manual de usuario

GE WSLP1500 Manual

Electrolux

Electrolux EWF1284EDW Manual de usuario

Bosch

Bosch WAN2829BSN Manual de usuario

LG TV2516DV3B Manual de usuario

LG TH2517DSAV Manual de usuario

VESTEL

VESTEL CMH-XL 7510 TE Manual de usuario

AEG

AEG 74335 Manual de operación

Johnson

Johnson JWF721A Manual de usuario

Beko

Beko WTE7604XLW0 Manual de usuario

Danby

Danby DTT100A1WDB Instrucciones de montaje

Amica

Amica WA 14 Ex Manual de usuario

Daewoo

Daewoo DWD-F1222 Manual de usuario

Bosch

Bosch WAS28461AU Manual de usuario

Miele

Miele PW 6080 Vario Manual de usuario

Finlux

Finlux FLX108CF220 Manual de usuario

Whirlpool

Whirlpool 3LBR5132AN0 Manual de usuario