Alliance Laundry Systems 39239R4 Manual de usuario

Installation

www.comlaundry.com

Automatic

Washers

Home Laundry

W001C

Part No. 39239R4

July 2007

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

Para bajar una copia de estas instrucciones

en español, visite www.comlaundry.com.

means without the expressed written consent of the publisher.

39239 1

Table of

Contents

Replacement Parts .............................................................................. 2

Installation........................................................................................... 3

Roughing in Dimensions ...................................................................... 3

Before You Start ................................................................................... 4

Tools ................................................................................................ 4

Electrical .......................................................................................... 4

Water................................................................................................ 4

Installing the Washer ............................................................................ 5

Step 1: Remove the Shipping Brace and Shipping Plug.................. 5

Step 2: Wipe Out Inside of Washtub ............................................... 5

Step 3: Connect Fill Hoses............................................................... 6

Step 4: Connect Drain Hose to Drain Receptacle ............................ 7

Step 5: Position and Level the Washer ............................................ 10

Step 6: Plug in the Washer............................................................... 11

Step 7: Add Water to the Washer .................................................... 11

Step 8: Check Lid Switch ................................................................ 11

Step 9: Check Installation ................................................................ 11

Electrical Requirements........................................................................ 12

Grounding Instructions .................................................................... 12

Water Supply Requirements................................................................. 13

Water Temperature .......................................................................... 13

Water Pressure ................................................................................. 13

Risers................................................................................................ 14

Installer Checklist................................................................ Back Cover

Replacement Parts

If replacement parts are required, contact the source

from which you purchased your washer, or contact:

Alliance Laundry Systems

Shepard Street

P.O. Bo x 99 0

Ripon, WI 54971-0990

Phone: (920) 748-3950

for the name and address of the nearest authorized

parts distributor.

39239

Installation

Roughing in Dimensions

TLW2075N

*With leveling legs turned into base.

28 in.

(71.1 cm)

25.6 in.

(65 cm)

26 in.

(66 cm)

0.4 in.

(1 cm)

*29 in. (73.7 cm)

*43 in. (109.2 cm)

*36 in. (91.4 cm)

*53 in. (134.6 cm)

*40.25 in. (102.2 cm)

22.13 in.

(56.2 cm)

Installation

39239

Before You Start

Tools

For most installations, the basic tools you will need

are:

Figure 1

Electrical

Refer to serial plate for specific electrical

requirements. For more detailed information, refer to

section on Electrical Requirements.

Water

Washer needs two standard 3/4 inch (19.1 mm) water

supply faucets with a pressure between 20 to 120

pounds per square inch (138 and 827 kPa). For more

detailed information, refer to section on Water Supply

Requirements.

D074I

1Wrench

2Screwdriver

3Pliers

4Level

D074I

Installation

39239

Installing the Washer

NOTE: If the washer is delivered on a cold day

(below freezing), or is stored in an unheated room

or area during the cold months, do not attempt to

operate it until the washer has had a chance to

warm up.

Step 1: Remove the Shipping Brace and

Shipping Plug

NOTE: Install dryer before washer. This allows

room for attaching exhaust duct.

Remove the shipping brace from under the lid. The

plastic shipping plug will be released from the base of

the washer when removing the cardboard base from

the washer.

Figure 2

NOTE: Do not tilt washer to front or sides when

moving.

The shipping brace and plug should be saved and must

be reinstalled whenever washer is moved or

transported to a new location. This will prevent

damage to washer components.

NOTE: Refer to your Use and Care Guide for

reinstalling shipping brace and shipping plug.

Step 2: Wipe Out Inside of Washtub

Prior to first wash, use an all purpose cleaner, or a

detergent and water solution, and a damp cloth to

remove shipping dust from inside of washtub.

Figure 3

TLW521N

1Shipping Brace

2Shipping Plug

W371I

Installation

39239

Step 3: Connect Fill Hoses

NOTE: Refer to section on Water Supply

Requirements before connecting fill hoses.

Turn on the water supply faucets and flush the lines for

approximately two minutes to remove any foreign

materials that could clog the screens in the water

mixing valve.

NOTE: When installing in newly constructed or

renovated building, it is very important to flush the

lines since build-up may have occurred during

construction.

Remove the two plain rubber washers and two filter

screens from accessories bag, and install them

according to Figure 4.

NOTE: Check filter screens for debris or damage

annually. Clean or replace them if necessary.

IMPORTANT: Thread hose couplings onto valve

connections finger-tight, then approximately 1/4

turn with pliers. DO NOT cross thread or

overtighten couplings.

Turn water on and check for leaks. If leaks are found,

retighten the hose couplings. Continue tightening and

rechecking until no leaks are found.

Figure 4

IMPORTANT: Hoses and other natural rubber

parts deteriorate after extended use. Hoses may

develop cracks, blisters or material wear from the

temperature and constant high pressure they are

subjected to.

All hoses should be checked on a yearly basis for

any visible signs of deterioration. Any hose showing

the signs of deterioration listed above should be

replaced immediately. All hoses should be replaced

every 5 years.

TLW1988N

1Filter Screen (Screen must be facing

outward)

2Fill Hose

3Rubber Washer (Plain)

4Cold Water Connection

5Hot Water Connection

6Install this end of hose to valve connections

at rear of washer.

7Install this end of hose to water supply

faucet.

8Faucet

HOT

COLD

134

Installation

39239

Step 4: Connect Drain Hose to Drain

Receptacle

Remove the drain hose from its shipping position on

the rear of the washer by unhooking the hose from the

retainer clamp.

Find the instructions, on the following pages, that are

appropriate for your type of drain receptacle

(standpipe, high standpipe, low standpipe, sink, wall,

or laundry tub). Follow these instructions to properly

install the drain hose.

IMPORTANT: Drain receptacle must be capable of

handling a minimum of 1-1/4 inch (3.2 cm) outside

diameter drain hose.

Figure 5

Standpipe Installation:

Place the hose into the standpipe.

Remove the beaded tie-down strap from accessories

bag and place around standpipe and drain hose,

approximately 12 inches (30 cm) down from the top of

pipe and tighten strap to hold hose to standpipe. This

will prevent the drain hose from dislodging from drain

receptacle during use.

IMPORTANT: To prevent siphoning, do not place

any ribbed portion of the drain hose into the

standpipe.

Figure 6

W324I

1Retainer Clamp

2Standpipe Adapter

TLW1961N

1Ribbed Portion of Drain Hose

2Standpipe Adapter

3Tie-Down Strap

4Standpipe 2 in. (5.08 cm) or 1-1/2 in. (4 cm)

Diameter

5Drain Hose Sleeve

TLW1961N

12 in.

(30 cm)

36 in.

(91.44 cm)

RECOMMENDED

HEIGHT

Installation

39239

High Standpipe Installation:

Place the hose into the standpipe. Remove the beaded

tie-down strap from accessories bag and place around

standpipe and drain hose, approximately 12 inches

(30 cm) down from the top of pipe and tighten strap to

hold hose to standpipe. This will prevent the drain

hose from dislodging from drain receptacle during use.

Figure 7

Low Standpipe Installation:

No. 562P3 Siphon Break Kit is required for this type

of installation. This kit is available (as optional

equipment at extra cost) through an authorized dealer

or parts distributor. Installation instructions are

supplied with the kit.

Figure 8

TLW1962N

1Drain Hose

2Standpipe (Standpipes higher than

4 feet [122 cm] are not recommended)

3Tie-Down Strap

4Standpipe Adapter

TLW1962N

W512I

1562P3 Siphon Break Kit

2Standpipe

3Drain Hose

W512I

Tabla de contenidos

Otros manuales de Arandela de Alliance Laundry Systems

Alliance Laundry Systems

Alliance Laundry Systems TLW12C SVG Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems H264I Guía

Alliance Laundry Systems

Alliance Laundry Systems FLW1548C SVG Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems HCD020GD2 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems LWS49N Series Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems POCKET HARDMOUNT UW50P4 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems CTLW-35A Guía

Alliance Laundry Systems

Alliance Laundry Systems HTE517xE2802 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems CPD6C Manual de instalación y operación

Alliance Laundry Systems

Alliance Laundry Systems CABINET HARDMOUNT HC80VNV Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems F232148 Guía

Alliance Laundry Systems

Alliance Laundry Systems UW POCKET HARDMOUNT UW35B2 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems Washer-Extractor Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems LTS84A*H Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems Washer Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems HFNKCASG116TN01 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems LWS01A* series Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems EA2011*A3000 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems UW35PV Series Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems NX18BVPA6 Guía

Alliance Laundry Systems

Alliance Laundry Systems Home Laundry Automatic Washers Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems 9001014R7 Guía de instalación

Alliance Laundry Systems

Alliance Laundry Systems Cabinet Hardmount SC27SN Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems H011C Manual de usuario

Manuales populares de Arandela de otras marcas

Tricity Bendix

Tricity Bendix AW 1000 W Guía del producto

Panasonic

Panasonic NA-F60L5WRB Manual de usuario

GE WSLP1500 Manual

Electrolux

Electrolux EWF1284EDW Manual de usuario

Bosch

Bosch WAN2829BSN Manual de usuario

LG TV2516DV3B Manual de usuario

LG TH2517DSAV Manual de usuario

VESTEL

VESTEL CMH-XL 7510 TE Manual de usuario

AEG

AEG 74335 Manual de operación

Johnson

Johnson JWF721A Manual de usuario

Beko

Beko WTE7604XLW0 Manual de usuario

Danby

Danby DTT100A1WDB Instrucciones de montaje

Amica

Amica WA 14 Ex Manual de usuario

Daewoo

Daewoo DWD-F1222 Manual de usuario

Bosch

Bosch WAS28461AU Manual de usuario

Miele

Miele PW 6080 Vario Manual de usuario

Finlux

Finlux FLX108CF220 Manual de usuario

Whirlpool

Whirlpool 3LBR5132AN0 Manual de usuario