Allen-Bradley FAST TRACK Manual de usuario
1
The Allen Bradley Manual for the FAST TRACKTM Printer
Contents:
1. Introduction
2. Products in the FAST TRACKTM Printer Kit
3. Safety precautions
3.1 Safety instructions
3.2 Precautionary measures
A Working with the FAST TRACKTM Printer
B Handling ink cartridges
C Suitable location for the printer
D Printer media
4. Installation and basic settings of FAST TRACKTM Printer Software
4.1 Installation of the FAST TRACKTM Printer Driver
4.2 Installation of the Status Monitor
4.3 FAST TRACKTM Printer Driver Settings
4.4 Installation of AB-Print Software
4.5 AB-Print Software Settings
5. FAST TRACKTM Printer Operating panel and LED indicators
6. Replacing or installing ink cartridges
7. Error indication
8. Error-related indicators
8.1 Deteriorating print quality
8.2 The print quality remains poor even after cleaning
8.3 Marker Cards are not drawn in/transported through
8.4 Marker Cards are not properly ejected
9. Problems with USB
10. Technical data
11. Warranty
2
1. Introduction
Installation instructions
This manual contains important information for the installation and initial start-up procedures for the
FAST TRACKTM Printer. It provides information for setting up the FAST TRACKTM Printer and the
software AB-Print.
Manual
This manual offers information for standard usage of the FAST TRACK TM Printer. In addition, it contains
tips for troubleshooting and information concerning technical data.
For further information, useful tips or the latest drivers, log onto:
http://www.ab.com/industrialcontrols/products
For additional information, you can contact us via e-mail or telephone:
[email protected]ockwell.com
1-440-646-5800
2. Products in the FAST TRACKTM Printer Kit
• FAST TRACKTM Printer (1492-PRTKIT110V or 1492-PRTKIT220V)
• Ink cartridge (1492-PRTINKCART)
• Cleaning cartridge (1492-PRTCLEAN)
• Input and output rails
• Parallel printer cable
• Power cord
• Short guide
• CD ROM for Printer drivers, AB-Print Software and manuals
Important:
The Allen Bradley ink cartridge, Cat. No. 1492-PRTINKCART, is required for initial
commissioning!
3
3. Safety precautions
3.1 Safety instructions
• Remove all shipping braces; open the FAST TRACKTM Printer cover and remove the transport
lock from the print head.
• Read the following instructions carefully before starting up the FAST TRACKTM Printer. Observe
the warnings and notices on the FAST TRACKTM at all times.
• Do not block or cover openings in the housing of the FAST TRACKTM Printer.
• Do not insert any objects into these openings.
• Do not spill any fluids onto the “FAST TRACKTM Printer.
• The main voltage must correspond to the system voltage given on the FAST TRACKTM Printer
label.
• Connect the device to a properly earthed socket outlet only. It must not be connected to a socket
outlet already being used by devices that are turned on and off at regular intervals, such as
photocopiers or ventilators.
• Do not connect the FAST TRACKTM Printer to either a switched or a timer-controlled socket
outlet.
• Do not use the computer system close to potential electromagnetic disturbance fields such as
loudspeakers or base transceiver stations for mobile telephones.
• Never use damaged or worn out power cables.
• If you connect the FAST TRACKTM Printer to the power supply via an extension cable, ensure
that the total nominal current of all of the devices connected to the extension cable does not
exceed the ampacity for that extension cable. In addition, you should ensure that the total
nominal current of all the devices plugged into the wall-mounted socket outlet does not exceed
the current carrying capacity for that socket outlet.
• Do not carry out repairs to the device yourself.
• Disconnect the FAST TRACKTM Printer and contact a qualified service engineer if any of the
following occurs:
• The power supply cable or the plug is damaged or worn.
• Fluids have penetrated the FAST TRACKTM Printer.
• The FAST TRACKTM Printer has been dropped or the housing damaged
• The FAST TRACKTM Printer does not operate normally or there are obvious signs of
malfunctions.
Caution: Warning signs to BGV A 8 (VBG 125), German employers liability insurance
regulations, & German standard DIN 4844.
Warning - Mind your hands
Do not reach inside
Warning - Hot surface
Do not touch
4
Attention:
Do not open the printers enclosure! Opening the enclosure will cause loss of
any warranty rights and may result in severe injuries.
3.2 Precautionary measures
Observe the following when using the FAST TRACKTM Printer, handling ink cartridges or choosing a
location to install the FAST TRACKTM Printer:
A. Working with the FAST TRACK TM Printer
• Check the wipe and scratch resistance of the ink at regular intervals.
• Do not put your hands inside the FAST TRACK TM Printer, and do not touch the ink cartridge
when the printer is in operation.
• Do not move the print head by hand, as this could damage the FAST TRACKTM Printer.
• Remove your printouts immediately after printing from the output rail of the FAST TRACKTM
Printer.
• Always turn the FAST TRACKTM Printer on/off using the main switch on the operating panel.
• Before transporting the FAST TRACKTM Printer, ensure that the print head is in the home
position (far right-hand side), and ensure that the ink cartridges are seated correctly.
B. Handling ink cartridges
• Keep unused ink cartridges in a cool and dry place.
• Keep ink cartridges out of reach of children. Never allow ink cartridges to fall into the hands of
children. Never allow anyone to drink from them.
• Always handle used ink cartridges with care, because a small amount of ink could remain in the
ink supply outlet. If you get ink on your skin, wash it thoroughly with soap and water. Consult a
doctor immediately, if after thoroughly rinsing the ink you still feel unwell or have problems with
your vision.
• Do not shake ink cartridges, as this can cause ink to leak.
• Install ink cartridges immediately after removing form the packaging. The print quality can be
impaired if an ink cartridge is left unpacked for any length of time before use.
• Do not use ink cartridges beyond the ‘use by date’ printed on the cartridge packaging. For best
results, the ink in the cartridge should be used within six months of installation.
• Do not dismantle or try to refill ink cartridges. This could result in damage to the print head.
• Before using an ink cartridge that has been stored in a colder place, allow the cartridge to
acclimatize to the room temperature for at least three hours.
• Do not touch the IC chip on the side of the cartridge. This could impair print operations.
Tamper proof label
5
• The IC chip in these ink cartridges contains a large amount of cartridge-specific information, for
example, the level of ink remaining in the cartridge, to ensure the trouble-free replacement of
the old ink cartridge with a new one. However, ink is used every time a new ink cartridge is
inserted, because the FAST TRACKTM Printer always carries out a reliability check.
• If you wish to remove an ink cartridge for use at a later date, then you must protect the ink
supply outlet from dust and becoming soiled. Please store the ink cartridge in the same
surroundings as the FAST TRACKTM Printer. Please note that a valve is fitted in the ink supply
outlet, which means that neither a cover nor a lid is required. However, you should always
handle ink cartridges with care, failure to do so could result in a leakage. Never touch the ink
supply outlet of the ink cartridge or the area around it.
• Applicable in Germany: ensure when connecting the FAST TRACKTM Printer to the power
supply that the building installation is fused with an appropriate back-up fuse.
This device is subject to special conditions regarding its connection to the mains supply.
The system impedance at the connecting point of the public supply system must not exceed
(0.14 + i 0.09) Ohm. In all other cases, consult the power supply company before connecting the
device to the public supply system. Please uninstall or deactivate the status monitor if you are
connecting the FAST TRACKTM Printer to a network.
C. Suitable location for the FAST TRACKTM Printer
• Place the FAST TRACKTM Printer on a flat, stable surface larger than base area of the printer.
The FAST TRACKTM Printer will not operate properly if it is on a tilt or at an angle.
• Ensure there is sufficient space to allow the Marker Cards to be ejected without hindrance from
the FAST TRACKTM Printer.
• Avoid installing the FAST TRACKTM Printer in any location where it is subject to rapid changes in
temperature and humidity. Ensure that the FAST TRACKTM Printer is not exposed to direct
sunlight, strong light or excessive heat.
• Avoid locations subject to impact shocks and vibrations.
• Do not install the device in dust-filled surroundings.
• When installing, ensure that the FAST TRACKTM Printer is sufficiently ventilated on all sides.
• Install the FAST TRACKTM Printer near a socket outlet, ensuring that the plug can be easily
removed at all times.
D. Printer media
Use the FAST TRACKTM Printer only for printing Allen Bradley 1492-M…Marker Cards.
6
4. Installation and basic settings of FAST TRACKTM Printer Software
4.1 Installation of the FAST TRACKTM Printer Driver
You must have administrator rights to install the printer drivers for the FAST TRACKTM Printer
and the AB-Print Software. Please install under Windows operating systems NT4.0 or Windows
2000 via the set up program ‘Install’. If necessary, please contact your system administrator.
1. Place the CD in the CD-ROM drive, and a window opens automatically. If no window opens, proceed
to item A; Otherwise, proceed to item 2.
If no window opens:
A. Click the My Computer icon on the Desktop
B. Select the CD-ROM drive displaying FAST TRACKTM Printer.
C. Using the mouse, right-click the CD symbol and select open.
D. Double-click the program CDMenuPro.exe to start.
7
2. In the window that opens, click the button for your preferred language.
3. Cick on the Printer Driver button.
8
4. In the window that opens please click the button for your operating system.
5. The software installation window will open, click Next to start the installation.
6. Follow the instructions on the monitor.
9
4.2 Installation of the Status Monitor
The Status Monitor will inform you about the status of the printer, any failures that might occur (e.g.
paper jam) and the current level of all ink cartridges. The screen will appear automatically with every
started print job. In the Utility menu you are able to activate or deactivate the Status Monitor.
To use the Status Monitor you have to install it separately!
Installation under Windows NT
Please do not install the status monitor if you wish to connect the FAST TRACKTM Printertoanetwork.
1. In the window please click the button Status Monitor.
2. The software installation window will open, click Next to start the installation.
3. Follow the instructions on the monitor.
It is possible that the Status Monitor creates problems once it is used in a network. In this case please
uninstall the Status Monitor or deactivate it with the following steps:
• Click Start > Settings > Printer.
• Select the Epson Stylus C62.
• Open Printer settings.
• On the Utility tab, click the Speed and Progress button.
• In the window that opens, clear the Show Progress Meter check box. Click OK to confirm.
10
4.3 FAST TRACKTM PrinterDriverSettings
1. Click Start > Settings > Printer to open the printer driver
2. Select the printer driver Epson Stylus C62
3. Select as required:
Windows 95 users: File > Properties > Printer settings
Windows 98 users: File > Properties > Printer settings
Windows 2000 users: File > Printer Preferences
Windows NT users: File > Document name
Then, carry out the following setting adjustments:
Best Photo
Plain Paper
Tabla de contenidos
Otros manuales de Impresora de Allen-Bradley
