Align Trex 700 Electric conversion Manual de instrucciones
www.KDEDirect.com
TREX 700 NITRO ELECTRONIC CONVERSION KIT
INSTALLATION INSTRUCTIONS
TOOLS REQUIRED:
4.5 mm Drill Bit (or equivalent ANSI #16 drill bit)
Manual or Power Drill
Motor Mount Installation Adhesive Diagrams (supplied with kit)
Drill the four orange-highlighted holes to 4.5 mm
diameter using the required drill bit and a manual
and/or power drill.
Attach the Motor Mount Installation Adhesive Diagram
to the frame (left and right sides provided for
corresponding frame pieces).
Drill the three Motor Mount hole locations (previous M3
mount editions have two locations) to 4.5 mm diameter
as directed by the orange crosshairs shown on the
Adhesive Diagram.
REVISION 4
www.KDEDirect.com
TREX 700 NITRO ELECTRONIC CONVERSION KIT
INSTALLATION INSTRUCTIONS
Install the M3 x 0.5 x 8 mm Socket Button Head Collar Screws to the blue-highlighted
locations (installation repeated on opposite side of frame).
Install the M3 Flat Washer, M3 x 0.5 Locknut, and the original Canopy Mounting Bolt to the
red-highlighted locations.
PARTS REQUIRED:
M3 x 0.5 x 8 mm Socket Button Head Collar Screws (included in original T700N kit)
M3 Flat Washers (supplied with kit)
M3 x 0.5 Locknuts (supplied with kit)
www.KDEDirect.com
TREX 700 NITRO ELECTRONIC CONVERSION KIT
INSTALLATION INSTRUCTIONS
Install the M3 x 0.5 x 8 mm Socket Button Head Collar Screws to the blue-highlighted
locations (center location included in latest production M3/M4 Motor Mounts).
Install the servos to the frame components using the M2.5 x 0.45 x 14 mm Button Head
Socket Head Cap Screws to the yellow-highlighted locations. The stock, self-tapping T2.6 x
14 mm screws are used for the plastic, threaded-hole locations (example: orange-highlighted
locations shown in the figure below).
PARTS REQUIRED:
M3 x 0.5 x 8 mm Socket Button Head Collar Screws (included in original T700N kit)
M2.5 x 0.45 x 14 mm Button Head Socket Head Cap Screws (supplied with kit)
T2.6 x 14 mm Button Head Self-Tapping Screws (included in original T700N kit)
www.KDEDirect.com
TREX 700 NITRO ELECTRONIC CONVERSION KIT
INSTALLATION INSTRUCTIONS
Install the M3 x 0.5 x 8 mm Socket Button Head Collar Screws to the blue-highlighted
locations.
Install the M3 Flat Washer and M3 x 0.5 Locknut to the red-highlighted location, which will
secure the frame to the original carbon braces.
`
PARTS REQUIRED:
M3 x 0.5 x 8 mm Socket Button Head Collar Screws (included in original T700N kit)
M3 Flat Washers (supplied with kit)
M3 x 0.5 Locknuts (supplied with kit)
M4 x 0.7 x 20 mm Socket Head Cap Screws (supplied with kit)
M4 Wide Flat Washers (included in original T700N kit)
M4 Flat Washers (supplied with kit)
Install the original Tail Boom Brace to the green-highlighted location with the
following fasteners in sequential order:
1. M4 x 0.7 x 20 mm Socket Head Cap Screw
2. M4 Wide Flat Washer
3. Tail Boom Brace Plastic Mount
4. M4 Flat Washer (x2, double-stacked for ~2.0 mm spacing)
5. Carbon Fiber Frame Brace
6. Carbon Fiber Main Frame
7. Aluminum Bottom Bracket Upgrade (rear M4 tapped hole location)
www.KDEDirect.com
TREX 700 NITRO ELECTRONIC CONVERSION KIT
INSTALLATION INSTRUCTIONS
Install the landing gear using the original T700N components (refer to the stock T700N manual
if needed).
Repeat all steps for the opposite Carbon Fiber Main Frame side and tighten all fasteners
(apply Loctite 242 to all fasteners during installation to prevent loosening during flight).
www.KDEDirect.com
TREX 700 NITRO ELECTRONIC CONVERSION KIT
INSTALLATION INSTRUCTIONS
The installation has been completed! Enjoy your new TREX 700N E-Conversion and make
sure to check the KDE Direct website (www.kdedirect.com) for newly released upgrades and
additions to your TREX 700 E-Conversion including:
TREX 700N E-Conversion Electronic Pinion Support
TREX 700N E-Conversion Elevator Servo Mount
TREX 700N E-Conversion Main Drive Gear, 115T, MOD 1.0
TREX 700N E-Conversion Performance Tail Upgrade V2
TREX 700N E-Conversion Thrusted Metal Bearing Blocks
TREX 700N E-Conversion Vertical Stabilizer Mount
KDE Direct 1917H-N42 High-Performance Brushless Motor
Otros manuales para Trex 700 Electric conversion
2
Tabla de contenidos
Otros manuales de Juguete de Align
Align
Align Trex 250 Combo KX019001TA Manual de usuario
Align
Align Combo T-REX 550E Manual de usuario
Align
Align nitro trex 600 KX0160NPNT Manual de usuario
Align
Align Trex 700 Electric conversion Manual de usuario
Align
Align T-rex 450SE Manual de usuario
Align
Align T-REX 450X Manual de usuario
Align
Align T-Rex 700E Combo Manual de usuario
Align
Align Trex 450 Plus Manual de usuario
Align
Align Trex 250 Pro Super Combo KX0190010T Manual de usuario
Align
Align T-rex 450SE Manual de usuario
Align
Align Trex 150 SFC RH15E01XT Manual de usuario
Align
Align T-REX 450PRO Manual de usuario
Align
Align RH50E07XT Manual de usuario
Align
Align Trex 700 Electric conversion Manual de usuario
Align
Align RH25E03XT Manual de usuario
Align
Align Trex 600 Nitro KX0160NPTL Manual de usuario
Align
Align Trex 450 Plus Manual de usuario
Align
Align Combo T-REX 550E Manual de usuario
Align
Align T-Rex 450 SE Manual de usuario
Align
Align TREX 700E V2 Manual de usuario
