Algo 8128 Manual de usuario
8128 SIP Strobe Light (G2)
8128 SIP Strobe Light (G2)
User Guide
Optional Accessories:
X128A AMBER lens cover
X128B BLUE lens cover
X128R RED lens cover
Document 90-00100C
11 27 2019
Page 1
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8128 SIP Strobe Light (G2)
Table o Contents
IMPORTANT SAFETY INFORMATION......................................................................................................4
OVERVIEW................................................................................................................................................. 8
Introduction.......................................................................................................................................... 8
What's New (compared to the original 8128).....................................................................................8
Key Features........................................................................................................................................ 9
Terminal Block Reset........................................................................................................................ 10
SETUP AND INSTALLATION...................................................................................................................11
Getting Started - Quick Install & Test...............................................................................................11
Ceiling and Wall Mounting................................................................................................................ 12
Programming and Con iguration......................................................................................................12
Inputs/Outputs................................................................................................................................... 13
FEATURES............................................................................................................................................... 14
SIP Paging: Single 8128.................................................................................................................... 14
SIP Ring Event................................................................................................................................... 14
Multicast Overview............................................................................................................................ 14
SIP Paging: Multiple 8128 (Using Multicast)....................................................................................15
SIP Paging: Multiple Strobe (Using Individual SIP extensions).....................................................15
SIP Activated Noti ication Alerts......................................................................................................15
TLS or SIP Signaling and Provisioning..........................................................................................16
WEB INTERFACE BASIC SETTINGS...................................................................................................... 21
Web Inter ace Login.......................................................................................................................... 21
Status.................................................................................................................................................. 22
Basic Settings Tab – SIP...................................................................................................................22
Basic Settings Tab – Features.......................................................................................................... 24
Basic Settings Tab – Strobe............................................................................................................. 25
Basic Settings Tab – Multicast......................................................................................................... 25
Basic Settings Tab – Multicast (Master Settings)...........................................................................27
Basic Settings Tab – Multicast (Slave Settings).............................................................................28
WEB INTERFACE ADDITIONAL FEATURES.........................................................................................30
Additional Features Tab – Input/Output........................................................................................... 30
Additional Features Tab – Emergency Alerts..................................................................................32
Additional Features Tab – More Page Extensions..........................................................................34
Additional Features Tab – More Ring Extensions..........................................................................35
WEB INTERFACE ADVANCED SETTINGS.............................................................................................37
Advanced Settings Tab – Network................................................................................................... 37
Advanced Settings Tab – Admin...................................................................................................... 39
Advanced Settings Tab – Time......................................................................................................... 42
Advanced Settings Tab – Provisioning............................................................................................43
Advanced Settings Tab – Advanced Audio.....................................................................................45
Advanced Settings Tab – Advanced SIP.........................................................................................47
Advanced Settings Tab – Advanced Multicast................................................................................50
WEB INTERFACE SYSTEM..................................................................................................................... 51
System Tab – Maintenance...............................................................................................................51
System Tab – Firmware..................................................................................................................... 52
Document 90-00100C
11 27 2019
Page 2
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8128 SIP Strobe Light (G2)
Advanced Settings Tab – File Manager...........................................................................................53
System Tab – System Log................................................................................................................ 54
WIRING CONNECTIONS.......................................................................................................................... 54
Network Connection.......................................................................................................................... 54
Connecting Input Devices................................................................................................................. 54
SPECIFICATIONS..................................................................................................................................... 56
FCC COMPLIANCE STATEMENT........................................................................................................... 57
Document 90-00100C
11 27 2019
Page 3
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8128 SIP Strobe Light (G2)
Important Sa ety In ormation
Important Sa ety In ormation
This product is powered by a certified limited power source (LPS), Power over
Ethernet (PoE); through CAT5 or CAT6 connection wiring to an IEEE 802.3at PoE+
or 802.3af compliant network PoE switch. The product is intended for installation
indoors. All wiring connections to the product must be in the same building. If the
product is installed beyond the building perimeter or used in an inter-building
application, the wiring connections must be protected against
overvoltage transient. Algo recommends that this product is installed by a qualified
electrician.
If you are unable to understand the English language safety information then
please contact Algo by email for assistance before attempting an installation
Consignes de Sécurité Importantes
Ce produit est alimenté par une source d’alimentation limitée certifiée (alimentation
par Ethernet); des câbles de catégorie 5 et 6 joignent un commutateur réseau à
alimentation par Ethernet homologué IEEE 802.3at PoE+ or 802.3af. Le produit est
conçu pour être installé à l’intérieur. Tout le câblage rattaché au produit doit se
trouver dans le même édifice. Si le produit est installé au-delà du périmètre de
l’édifice ou utilisé pour plusieurs édifices, le câblage doit être protégé des
surtensions transitoires. Algo recommande qu’un électricien qualifié se charge de
l’installation de ce produit.
Si vous ne pouvez comprendre les consignes de sécurité en anglais, veuillez
communiquer avec Algo par courriel avant d’entreprendre l’installation au
In ormación de Seguridad Importante
Este producto funciona con una fuente de alimentación limitada (Limited Power
Source, LPS) certificada, Alimentación a través de Ethernet (Power over Ethernet,
PoE); mediante un cable de conexión CAT5 o CAT6 a un conmutador de red con
PoE en cumplimiento con IEEE 802.3at PoE+ or 802.3af. El producto se debe
instalar en lugares cerrados. Todas las conexiones cableadas al producto deben
estar en el mismo edificio. Si el producto se instala fuera del perímetro del edificio
o se utiliza en una aplicación en varios edificios, las conexiones cableadas se
Document 90-00100C
11 27 2019
Page 4
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8128 SIP Strobe Light (G2)
deben proteger contra sobretensión o corriente transitoria. Algo recomienda que la
instalación de este producto la realice un electricista calificado.
Si usted no puede comprender la información de seguridad en inglés,
comuníquese con Algo por correo electrónico para obtener asistencia antes de
intentar instalarlo: [email protected].
Wichtige Sicherheitsin ormationen
Dieses Produkt wird durch eine zertifizierte Stromquelle mit begrenzter Leistung
(LPS – Limited Power Source) betrieben. Die Stromversorgung erfolgt über
Ethernet (PoE – Power over Ethernet). Dies geschieht durch eine Cat-5-
Verbindung oder eine Cat-6-Verbindung zu einer IEEE 802.3at PoE+ or 802.3af-
konformen Ethernet-Netzwerkweiche. Das Produkt wurde konzipiert für die
Installation innerhalb eines Gebäudes. Alle Kabelverbindungen zum Produkt
müssen im selben Gebäude bestehen. Wenn das Produkt jenseits des Gebäudes
oder für mehrere Gebäude genutzt wird, müssen die Kabelverbindungen vor
Überspannung und Spannungssprüngen geschützt werden. Algo empfiehlt das
Produkt von einem qualifizierten Elektriker installieren zu lassenv.
Sollten Sie die englischen Sicherheitsinformationen nicht verstehen, kontaktieren
Sie bitte Algo per Email bevor Sie mit der Installation beginnen, um Unterstützung
zu erhalten. Algo kann unter der folgenden E-Mail-Adresse erreicht werden:
安全须知
本产品由认证的受限电源（LPS）以太网供电（PoE）通过 CAT5 或CAT6 线路联接至
IEEE 802.3at PoE+ or 802.3af 兼容的 PoE 网络交换 供电。本产品适用于室内或建筑物周
边安装。所有联接本产品的线路必须源自同一建筑物。本产品如需用于超出建筑物周边范
围或跨建筑物的安装线路联接部分必须有过压和瞬态保护。Algo 建议本产品由专业电工
安装。
如果您对理解英文版安全须知有问题安装前请通过电子邮件和 Algo 联
EMERGENCY COMMUNICATION
The 8128 SIP Strobe Light is not intended for fire alarm signaling applications. The
8128 SIP Strobe Light is intended for informative signaling in conjunction with
unified communication systems. The 8128 Strobe Light is suitable for OSHA and
ADA compliance when properly located and configured
Document 90-00100C
11 27 2019
Page 5
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8128 SIP Strobe Light (G2)
DO NOT LOOK DIRECTLY
Do not look directly at the 8128 SIP Strobe Light while operating in close proximity,
as vision may be affected. The LEDs in the 8128 light are classified according to
the IEC 62471-2006 standard as “RG-1” for risk group 1. This is defined as “Low
risk. No photobiological hazard under nor al behavioral li itations.”
PHOTO-SENSITIVITY
Photo-sensitivity in some people with epilepsy can trigger seizures from flashing or
flickering lights. It is possible that some flash patterns of the 8128 SIP Strobe Light
could trigger a seizure for some individuals under some conditions. High intensity
patterns should only be selected if necessary for the 8128 to be effective.
WET OR OUTDOOR ENVIRONMENTS
The 8128 SIP Strobe Light is intended for indoor or outdoor locations and may be
subjected to spray or weather provided the rear wiring cavity is properly sealed to
prevent water ingress.
Gaskets included with the 8128 SIP Strobe Light may be effective against water
ingress on some, but not all surfaces in which case additional protective measures
must be taken such as a perimeter sealant.
CAT5 or CAT6 connection wiring to an IEEE 802.3at PoE+ or 802.3a compliant
network PoE switch must not leave the building perimeter without adequate
lightning protection.
No wiring connected to the 8128 SIP Strobe Light may leave the building
perimeter without adequate lightning protection.
Document 90-00100C
11 27 2019
Page 6
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8128 SIP Strobe Light (G2)
Overview
Introduction
The 8128 SIP Strobe Light (G2) is a SIP compliant, multicast capable, PoE high-
intensity white strobe light. The flash intensity can be chosen to suit the application
and environment. There are non-flashing patterns for passive gentle notification
and aggressive patterns for maximum conspicuity in busy environments.
The 8128 is typically wall or ceiling mounted. The 360° x 180° visibility, 11
available flash patterns, 3 intensity settings, and optional colored covers (amber,
blue, and red) makes the 8128 suitable for notification and alerting of telephone,
emergency, safety, and security events. Light output is equally intense in every
direction unless a directional pattern is chosen.
The 8128 SIP Strobe Light can be activated by:
•SIP Ring
•SIP In-Use (Subscribe Notify)
•Dry contact closure input
•Multicasting
Multiple Algo endpoints in a SIP environment require only one device to register as
a SIP extension. Multicasting capabilities allow the SIP registered strobe to flash
and simultaneously stream multicast events to the other Algo strobes, speakers
and paging adapters in any combination and number of endpoints.
The 8128 SIP Strobe Light is configured using central provisioning features or by
accessing a web interface using browsers such as Google Chrome or Firefox.
What's New (compared to the original 8128)
The 8128 SIP Strobe Light (G2) is the next generation of the popular Algo 8128.
The device has upgraded hardware capable of running the latest security and
encryption standards, including TLS, ensuring secure communication with hosted
SIP providers.
Designed to include all the features of the original 8128, the second generation
has a number of new features such as enhanced multicast options, dedicated
‘Emergency Alert’ Extensions, and more.
As this device now runs on a new hardware platform, note that the firmware files
are different compared to the original 8128. For assistance migrating provisioning
files for this new device, please contact Algo support.
Document 90-00100C
11 27 2019
Page 7
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8128 SIP Strobe Light (G2)
Key Features
SIP Extensions
The 8128 connects to an on-premise or hosted communication server in the same
way as a SIP telephone. To register the 8128 with the server requires the following
information:
1. IP address (e.g. 192.168.1.111) or domain name (e.g. myserver.com) of the
SIP Server
2. SIP extension (e.g. 3790)
3. Authentication ID
4. Password
The 8128 supports two SIP extensions which behave differently – RING and
PAGE. One or both may be used depending on the application. If the RING
extension is called the 8128 will not answer. Instead, it will flash a light pattern until
the inbound call stops ringing. Typically the RING extension is programmed as
part of a hunt group so that it receives a ring signal simultaneously with one or
more devices.
If the PAGE extension is called, the 8128 will answer and flash a light pattern until
the call is ended.
Multicasting
Allows multiple units to simultaneously flash light patterns. The 8128 can be
configured as a multicast ‘Master’ device to send a multicast stream to other slave
devices. The 8128 can be configured as a multicast ‘Slave’ device to flash a light
pattern when a stream is received from a multicast ‘Master’ device. Any
number combination of Algo IP speaker, paging adapter, or strobe endpoint can
be configured as multicast ‘Slaves’. This feature provides scalability without
requiring each endpoint Slave to be registered with a SIP extension.
PolycomTM Group Paging
The 8128 supports Polycom Group Paging. The 8128 can be added to a Polycom
Group Page so that voice paging activates a flash pattern while active.
Con iguration & Provisioning
Configuration can be done through a web interface control panel or central
provisioning features. Central provisioning allows units to be pre-configured for a
specific server prior to deployment in the field. Configuration files are automatically
downloaded from a server (via TFTP, FTP, HTTP, HTTPS) using DHCP.
Document 90-00100C
11 27 2019
Page 8
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8128 SIP Strobe Light (G2)
Terminal Block Reset
The reset relay terminal on the back can be used to reset the 8128 SIP Strobe
Light at time of power up. To return all the settings to the factory default for the
8128, wait until the LED flashes, then connect the reset terminals and hold until
the 8128 LED begins a double flash pattern. Release the reset connection and
allow the unit to complete its boot process.
A reset will set all con iguration options to actory de ault including the
password.
Document 90-00100C
11 27 2019
Page 9
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8128 SIP Strobe Light (G2)
Setup and Installation
Getting Started - Quick Install & Test
This guide provides i portant safety infor ation which should be read
thoroughly before per anently installing the strobe.
1. Connect the 8128 SIP Strobe Light to a 802.3af compliant PoE network switch using
the RJ45 jack in the back recess of the housing.
2. Allow the 8128 SIP Strobe Light time to boot, about 30 seconds. While booting the
Strobe will activate a small dim white light in the center.
3. If there is no DHCP server found the 8128 SIP Strobe Light will default to the static
IP address 192.168.1.111. Most often however the 8128 will be assigned an IP
address. The IP address may be discovered by downloading the Algo Locator Tool
to find Algo devices on your network: www.algosolutions.com locator
4. Access the 8128 web page by entering the IP address into a browser (Chrome,
Firefox etc.) and login using the default password: algo
5. Enter the IP address for the SIP server into the SIP Domain field under the Basic
Settings > SIP tab.
6. Enter the Ring and or Page SIP extension and credentials. Leave the credentials
blank for either extension if there is no intended use to have both registered.
(Note: The strobe supports multiple Ring, Emergency Alert, and Page SIP
extensions. The Page extension auto-answers and flashes a light pattern. The Ring
and Emergency Alert extensions will flash a light pattern without answering.)
7. Make a test call from a telephone to the strobe for one or both extensions. The Page
SIP extension should auto-answer and flash the light pattern. The Ring SIP
extension will flash the light pattern without answering the call.
Document 90-00100C
11 27 2019
Page 10
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
Otros manuales para 8128
1
Tabla de contenidos
Otros manuales de Equipo de iluminación de Algo
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
