Alfalaval CM Manual de usuario
Alfa Laval CM
Condition Monitor
BRITISH ENGLISH
2067-0000
Lit. Code 200002050-2-EN-GB
Manual No. 100002845 Instruction manual
Published by
Alfa Laval Kolding A/S
Albuen 31
DK-6000 Kolding, Denmark
+45 79 32 22 00
The original instructions are in English
© Alfa Laval Corporate AB 2021-06
This document and its contents are subject to copyrights and other intellectual property rights owned by Alfa Laval Corporate AB. No part of this document may be copied, re-produced or
transmitted in any form or by any means, or for any purpose, without Alfa Laval Corporate AB’s prior express written permission. Information and services provided in this document are
made as a benefit and service to the user, and no representations or warranties are made about the accuracy or suitability of this information and these services for any purpose. All rights
are reserved.
Contents
1 EC Declaration of Conformity.......................................................................... 5
2 About Condition Monitor...................................................................................... 7
2.1 Purpose of this manual..............................................................................................8
2.2 Use of symbols..........................................................................................................9
3 Installation................................................................................................................... 11
3.1 General Guidelines..................................................................................................11
3.2 Alfa Laval equipment guidelines.............................................................................. 11
3.3 Setup....................................................................................................................... 12
3.4 Software.................................................................................................................. 13
4 Safety............................................................................................................................. 15
4.1 Product.................................................................................................................... 15
4.2 Safety – Installation................................................................................................. 15
4.3 Recycling information.............................................................................................. 15
5 Troubleshooting.......................................................................................................17
5.1 Magnet functionality.................................................................................................17
5.2 Tips and tricks......................................................................................................... 19
5.3 Parts lists.................................................................................................................19
6 Addendum...................................................................................................................21
1 EC Declaration of Conformity
The Designation Company
Alfa Laval Kolding A/S
Compagny Name
Albuen 31, DK-6000 Kolding, Denmark
Address
+45 79 32 22 00
Phone No
hereby declare that
Alfa Laval CM Condition Monitor
Designation Type
Conformities
- ESTI EN 301 480 - 1 Electromagnetic Compatibility (EMC)
- CISPR32 EN 55032 - Electromagnetic compatibility of multimedia equipment.
- ESTI EN 300 328 V2.1.1 - Wide band transmission system
- IEC 62479;2010 - Assessment of the compliance of low power electronic and electronical equipment with the
basic restrictions related to human exposure to electromagnetic fields (10 MHz to 300 GHz).
- IEC 62368-1:2018 - Audio/video, information and communication technology equipment.
- FCC part 15.247 - Spread spectrum systems
- Telecom
- RoHS2 Directive 2011/65/EU
- REACH
The person authorised to compile the technical file is the signer of this document
Global Product Quality Manager
Hygienic Fluid Handling Lars Kruse Andersen
Title Name Signature
Kolding 2018–10–01
Commpany
Date
200002050-2-EN-GB 5
EN
ISED Statements:
This Device complies with Industry Canada License-exempt RSS standard(s). Oper-
ation is subject to the following two conditions: (1) this device may not cause interfer-
ence, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de
brouillage ; (2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
FCC Statements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications to the equipment not expressly approved by the party re-
sponsible for compliance could void the user's authority to operate the equipment.
This portable device with its antenna complies with FCC/IC RF exposure limits for
general population / uncontrolled exposure. The antenna used for this device must
not be co-located or operating in conjunction with any other antenna or transmitter.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interfer-
ence to radio communications.
However, there is no guarantee that interference will not occur in a particular installa-
tion.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the re-
ceiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
200002050-2-EN-GB6
1 EC Declaration of ConformityEN
2 About Condition Monitor
The Condition Monitor (CM) is a compact, easy to use, vibration monitoring system which allows the
user to monitor the condition of rotating equipment. The CM is battery powered, and communication is
performed wirelessly by means of Bluetooth, thus no need for cabling.
During operation, the CM measures equipment vibration. The measurements are compared against a
baseline set during an initial “Teach” calibration period, which reflects a normal condition. The user is
notified in case of vibration deviations that exceeds user configurable thresholds.
Advanced frequency analysis functions assist the user in detecting maintenance demanding
equipment components in due time, so that maintenance can be carried out as a planned operation.
A minimum of 1 year of measurements can be stored directly on the CM.
NOTE
The CM shall be used in conjunction with a handheld device (not included) running Android or iOS
with the Alfa Laval Condition Monitor application installed.
The battery life of the CM is expected to be at least 2-3 years under normal operating conditions.
Since this depends on user behavior, battery life time is excluded from warranty.
NOTE
The CM is approved for use in the following contries:
United States, Canada, China and The United Kingdom, Europe; Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden and The
Netherlands, EFTA; Switzerland, Iceland, Liechtenstein and Norway.
200002050-2-EN-GB 7
EN
2.1 Purpose of this manual
NOTE
Save this manual for future reference and keep it readily available. For detailed use of product guidance,
consult the Alfa Laval Condition Monitor application. Requesting other information for instructions,
situations, or events that are not considered in this manual or in the sales documents, please contact your
local Alfa Laval representative. Always specify the exact product type and identification code when
requesting technical information or spare parts.
The purpose of this manual is to provide necessary information for:
•Installation
•Safety
•Recycling
•Troubleshooting
•Related documents
200002050-2-EN-GB8
2 About Condition MonitorEN
2.2 Use of symbols
This section describes the symbols used throughout this manual.
NOTE
Note
Information considered important to the
reader, but not related to hazards.
ATTENTION
Attention
Informs the reader about a potential haz-
ard, if not avoided will result in serious
injury.
HOT SURFACE
Hot surface
Informs the reader about potential hot
surfaces.
RELATED SECTION /
REFERENCE
Related section / reference
Informs the reader about a section or ref-
erence containing further detailed infor-
mation.
200002050-2-EN-GB 9
About Condition Monitor 2 EN
200002050-2-EN-GB10
2 About Condition MonitorEN
Otros manuales para CM
2
Tabla de contenidos
