ALcom Clarigo C11 Manual
1
2
Contents
Setup Flow Chart...................................................... .... ..3
Part I. System Information
1.1 Reset to default................................................. ... ..4
1.2 Firmware version............................................... .. ..4
Part II. Interface Setting
2.1 Interface ........................................................... .....5
Part III. Keyboard Parameters
3.1 Terminal Type .................................................... ...6
3.2 Language Selection ......................................... .....7
3.3 Function Key Emulation ................................ ..... .8
3.4 Keyboard Emulation .................................... .........8
3.5 ALT Mode ..................................................... ........9
3.6 Caps Lock ..................................................... ........9
3.7 Numeric Key .................................................. .......9
3.8 Inter-Character Delay .................................... ......10
3.9 Delay After Transmit (Keyboard Wedge) ...... ......10
3.10 Keyboard Speed ........................................... ....10
3.11 Keyboard Wedge Terminator ......................... ...10
Part IV. RS-232 Protocol
4.1 Baud Rate ................................................... ...... .11
4.2 Data Bits ....................................................... ..... 11
4.3 Stop Bits ....................................................... ... .12
4.4 Parity Check .................................................. ... 12
4.5 Inter-Character Delay ...................................... . ..12
4.6 Delay After Transmit ...................................... ... . 12
4.7 Response Delay Time .................................... ... .13
4.8 Flow Control .................................................... . ..13
4.9 RS-232 Interface Terminator ......................... ... ..13
Part V. System Setting
5.1 Scan Mode .................................................... .. ...15
3
5.2 Buzzer ......................................................... ........16
5.3 String ............................................................. .....18
5.4 Barcode Inverse .......................................... ........20
Part VI. Barcode Type Setting
6.1 UPC-A ....................................................... ..........22
6.2 UPC-E ..................................................... ............24
6.3 EAN-13........................................................... .....26
6.4 EAN-8................................................... ...............28
6.5 Code 39...................................................... .........29
6.6 Codabar....................................................... ........32
6.7 Code 93......................................................... ......34
6.8 Code 128 .................................................... ........36
6.9 Interleaved 2 of 5......................................... .......38
6.10 Industrial 2 of 5.......................................... ........40
6.11 Matrix 2 of 5............................................ ...........42
6.12 China Post Code.................................... .......... .44
6.13 MSI/Plessey........................................... ......... ..45
6.14 Code 32................................................... ..........47
6.15 Code 11........................................................ .....49
6.16 RSS (Optional) ......................................... ...... . 51
6.17 Telepen ................................................. ........... 52
Appendix A.................................................... ............ . 54
Appendix B................................................... .......... . 56
4
Setup Flow Chart
◆Note:
Note:Note:
Note:
1. Scan “firmware version barcode”, the
Version No. will
be displayed on monitor.
The default settings are shown with < > and bold in the
following sections.
Scan “End” barcode
Scan the barcode you like to
change to change
Hex or ASCII Code
Reset to default
YES
NO
5
Part I
Part I Part I
Part I System
SystemSystem
System
Information
InformationInformation
Information
1.1 Reset to default
Reset to defaultReset to default
Reset to default:
::
:
Reset to factory default settings. The default s
ettings
are shown with < > and bold.
1.2 Display
Display Display
Display Firmware Version
Firmware VersionFirmware Version
Firmware Version:
::
:
Scan barcode to display firmware version.
Start Configuration
Reset to default
Firmware Version
End Configuration
6
Part II System Setting
2.1 Interface:
2.1 Interface:2.1 Interface:
2.1 Interface:
Part I System Information
7
1.3 Reset to default:
Reset to factory default settings. The default settings are
shown with < > and bold.
1.4 Display Firmware Version:
Scan barcode to display firmware version.
Start Configuration
Reset to default
Firmware Version
End Configuration
Part II System Setting
8
2.1 Interface:
Start Configuration
PS/2
Keyboard
RS-232
< USB
Keyboard >
< USB
Virtual COM >
End Configuration
Part III Keyboard wedge parameters
9
3.1 Terminal Type:
Start Configuration
< IBM AT >
Reserved
Reserved
Reserved
Reserved
Reserved
10
Reserved
Reserved
End Configuration
3.2 Language Selection:
Start Configuration
American
Italian
Spanish
Tabla de contenidos
