Albasca MK-5500ZB Manual de usuario

V1.03

MK-5500ZB

Wireless Area Imager Barcode Scanner

Configuration Guide

Factory Defaults

Scanning the following barcode can restore the engine to the factory defaults.

Restore All FactoryDefaults

Chapter 1

Communication Interfaces

USB HID-KBW

USB COM Port Emulation

If you connect the engine to the Host via a USB connection, the USB COM Port Emulation feature

allows the Host to receive data in the way as a serial port does.A driver is required for this feature.

USB COM Port Emulation

Dongle interface selection

Scan the interferface you wish to use and replug the USB receiver to active

the new setting.

HID USB Keyboard Country

Note: Please scan the following barcode directly with your USB

receiver on. No need to scan start and end conﬁguration barcodes.

Italian

Spanish

French

Turkey

German

Finnish

Portuguese

Dutch

Czech

Norwegian

Belgian

Swiss

Swedish

Danish

Japanese

Scan the appropriate country code below to program the kayboard for your country.

As a general rule , the following characters are supported,but need apecial care for

countries other than the United States: @ | $ # { } [ ] = / ' \ < > ~

Convert Case

Scan the appropriate barcode below to convert barcode data to your desired case.

*No Case Conversion

Convert All to Upper Case Convert All to Lower Case

Example: When the Convert All to Lower Case feature is enabled, barcode data “AbC” is transmitted

as “abc”.

Cellphone Mode 1

If the Cellphone Mode is enabled, the engine activates a special capturing image and illumination

session. Every 3 frame open one illumination.

When the backlight of cellphone is weak and the reflection is strong ,please scan mode 1

Cellphone Mode 1

When the backlight of cellphone is not weak and the reflection is strong ,please scan mode 2

Cellphone Mode 2

Chapter 2 General Configuration

Video Reverse

On Off

Illumination

On Off

Beeper Tone - Good Read

Off

Middle

High

Chapter 3 Data Formatting

General Configuration

Add CR Add LF

Add CRLF Add TAB

Add Prefix

Add Prefix Clear Prefix

Save Not Save

To set a custom preffix, scan the Set Custom Prefix barcode and the numeric

barcodes representing the hexadecimal values of a desired Prefix and then scan

the Save barcode. Refer to Appendix 4: ASCII Table for hexadecimal values of

characters.

Example: Set the custom Prefix to “ODE”

1. Check the hex values of “ODE” in the ASCII Table. (“ODE”: 4F, 44, 45)

2. Scan the Set Custom Prefix barcode.

3. Scan the numeric barcodes”9”,”9”, “4”, “F”, “4”, “4”, “4” and “5”in Appendix 5 .

Remark: Please first scan numeric barcode "9" , "9" before adding any charcaters.

4. Scan the Save barcode.

Add Suffix

Add Suffix Clear Suffix

Save Not Save

To set a custom preffix, scan the Set Custom Prefix barcode and the numeric

barcodes representing the hexadecimal values of a desired Prefix and then scan

the Save barcode. Refer to Appendix 4: ASCII Table for hexadecimal values of

characters.

Example: Set the custom Prefix to “ODE”

1. Check the hex values of “ODE” in the ASCII Table. (“ODE”: 4F, 44, 45)

2. Scan the Set Custom Prefix barcode.

3. Scan the numeric barcodes”9”,”9”, “4”, “F”, “4”, “4”, “4” and “5”in Appendix 5 .

Remark: Please first scan numeric barcode "9" , "9" before adding any charcaters.

4. Scan the Save barcode.

Chapter 4 Symbologies

General Settings

Enable/Disable All Symbologies

If the Disable All Symbologies feature is enabled, the engine will not be able to read any

non-programming barcodes except the programming barcodes.

Enable All Symbologies Disable All Symbologies

1D Symbologies

Code 128

Restore Factory Defaults

Restore the FactoryDefaults of Code 128

Otros manuales para MK-5500ZB

Tabla de contenidos

Otros manuales de Lector de código de barras de Albasca

Albasca

Albasca MK-5500ZB Manual de usuario

Albasca

Albasca MK-5500 Manual de usuario

Albasca

Albasca CCD-820 Manual de usuario

Albasca

Albasca MK-5800BT Manual de usuario

Albasca

Albasca FUNK MK-5120ZBe Manual de usuario

Albasca

Albasca MK-5800BT Manual de usuario

Albasca

Albasca MK-5200 Manual de usuario

Albasca

Albasca MK-1200ZB Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario