Akai AK-FDWD Manual de usuario
560L Side by Side Refrigerator
INSTRUCTION MANUAL
MODEL: AK-FDWD
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | info@tempo.org
2
Contents
03 General Safety Instructions
06 Product Overview
07 Installation
10 Instructions
17 FAQs and Troubleshooting Guide
19 Other Useful Information
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | info@tempo.org
3
General Safety Instructions
Pay particular attention to messages that follow this safety alert symbol
or the words DANGER, WARNING or CAUTION. These words are used
to alert you to a potential hazard that can seriously injure you and others.
The instructions will tell you how to reduce the chance of injury and let
you know what can happen if the instructions are not followed.
Refrigerant matters
WARNING: Do not damage the refrigerant circuit! Never use an appliance with a
damaged refrigerant circuit! If the refrigerant circuit becomes damaged during transport
or installation, avoid proximity to open fires and all types of heat and ignition sources.
Thoroughly ventilate the room in which the appliance is located.
The room for installing the appliance must be at least 1m³ per 8g of refrigerant.
The amount and type of refrigerant in the appliance can be found in the technical
specifications on page 20 and on the appliance rating plate. It is hazardous for anyone
other than an authorised service person to service this appliance. In Queensland,
the authorised service person MUST hold a Gas Work Authorisation for hydrocarbon
refrigerants to carry out servicing or repairs which involve the removal of covers.
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
Read this manual thoroughly before first use, even if you are familiar with this type of
product. The safety precautions enclosed herein reduce the risk of fire, electric shock and
injury when correctly adhered to. Keep the manual in a safe place for future reference,
along with the completed warranty card, purchase receipt and carton. If applicable, pass
these instructions on to the next owner of the appliance.
This symbol alerts you to take care as the appliance contains flammable
materials: isobutane as refrigerant and cyclopentane as insulation
blowing gas. While isobutane (R600a) is a gas with a high level of
environmental compatibility, it is nevertheless flammable. Do not expose
the appliance to high heat, sparks and open flames.
Responsible disposal
At the end of its working life, do not throw this appliance out with your household waste.
Electrical and electronic products contain substances that can have a detrimental
effect on the environment and human health if disposed of inappropriately. Observe any
local regulations regarding the disposal of electrical consumer goods and dispose of it
appropriately for recycling and recovery of the refrigerant and blowing agent.
WARNING! This refrigeration appliance contains flammable refrigerants and insulation
blowing gases, which must be removed before disposal. Contact your municipal
authorities for any codes or regulations concerning the disposal of such materials.
DANGER! Risk of child entrapment: When discarding this or another refrigerator, pull
the plug out of the socket, cut the connection cable (as close to the appliance as you can)
and remove the doors to prevent playing children to suffer electric shock or to get trapped
inside the appliance. If the discarded appliance has a spring lock (latch) on the door or lid,
make the spring lock unusable to prevent it from becoming a death trap for children.
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | info@tempo.org
4
To reduce the risk of fire, electric shock or injury, always follow basic safety precautions
and accident prevention measures when using this appliance, including the following:
Electrical safety
• Voltage: Plug the appliance in a 220-240V, 50Hz, properly earthed power outlet,
which must be in good working order. Make sure your outlet voltage and circuit
frequency correspond to the voltage stated on the appliance rating label.
• Power connection: Do not use an adaptor; do not use an extension cord. Plug
the power plug directly into a separate power point that cannot easily be turned off
accidentally, and that is easily accessible so you can switch it off when required.
• Power cord: Do not kink or damage the power supply cord. Do not leave it exposed
or dangling. Secure it behind the appliance so no one steps on or places anything on
the cord or against it. A squashed or damaged power plug may overheat and cause a
fire.
• Damaged cord: Do not use a cord that shows cracks or abrasion damage along its
length or at either end. Any damage to the cord may cause a short circuit, fire and/or
electric shock. If the power cord is damaged, it must be replaced by the manufacturer
or its service agent. Contact the after sales support line for advice.
• Disconnection: Never unplug the unit by pulling the cord. Always grip the plug firmly
and pull straight out from the power point.
• Electrical work: All electrical work associated with the installation must be carried
out by a licensed electrician.
General Safety Instructions (Cont.)
Usage conditions and restrictions
• Indoor domestic use only: This appliance is intended for indoor domestic use only.
It is not suitable for industrial or commercial use.
• Intended purpose: Do not use this appliance for anything other than its intended
purpose, and only use it as described in this manual. Do not attempt to alter or
modify this appliance in any way.
• Usage restrictions: This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction
concerning the use of the appliance by a person responsible for their safety.
• Children: Supervise children to ensure they do not play with the appliance. Close
supervision is necessary when any appliance is used by or near children. Never
allow children to operate, play with or crawl inside the appliance.
• WARNING! Do not use any electrical appliances (such as ice cream makers)
inside refrigeration appliances, unless they are approved for this purpose by the
manufacturer.
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | info@tempo.org
5
General Safety Instructions (Cont.)
Cleaning and maintenance
• Disconnect: Switch off and unplug the appliance from the mains socket before
cleaning, maintenance or servicing. Failure to do so can result in electric shock, injury
or death. Do not connect or disconnect the plug when your hands are wet.
• Flames: Do not let open flames or ignition sources enter the appliance.
• Flammable/explosive substances: Never clean this appliance with flammable fluids.
Do not store or use volatile, flammable or explosive substances such as aerosol cans
with a flammable propellants in or close to this or any other appliance. The fumes can
create a fire hazard or explosion.
• Solvents: Do not use solvent based cleaning agents or abrasives on the interior as
these may damage or discolour the surfaces of the appliances.
• WARNING! Do not use mechanical devices or other means to accelerate the defrost-
ing process, other than those recommended by the manufacturer. Never use a sharp or
metal instrument to remove frost or clean the fridge. Use a plastic scraper, if necessary.
• Service: Do not attempt to repair, modify or replace any part of the appliance unless
specifically recommended in this manual. Refer all other servicing to a qualified
technician, or contact the after sales support centre for advice.
Installation (see pages 7–9 for comprehensive installation instructions)
• Heavy: This appliance is heavy, take care when moving it. To avoid back or other injury,
consider a two person lift or mechanical aid when installing it. Failure to do so can
result in back or other injury.
• Freestanding design: This appliance is designed to be freestanding only and should
not be recessed or built in.
• Keep it upright: Do not tilt the fridge more than 45º from upright when moving it.
• Handle with care: Do not apply force to any part such as the condenser or door.
• WARNING: Ventilation: To ensure proper ventilation, keep any ventilation openings,
in the appliance enclosure or in the built-in structure, clear of obstructions. Ensure
adequate air circulation around the appliance to prevent overheating.
• Level: Install the appliance level in order to ensure proper operation (see page 9).
• Location: Install the appliance in an area that meets the following requirements:
• Ambient temperature: The ambient temperatures must correspond to the climate
class (T) indicated on the rating plate of the appliance: 16°C–43°C.
• Floor surface: The floor must be sturdy, level (or nearly level) and strong enough to
support the unit when it is fully loaded.
• Areas to avoid: Avoid areas where the appliance would be exposed to direct sunlight,
sources of heat (stove, heater, radiator, etc.), extreme cold ambient temperatures or
excessive moisture and high humidity (such as outdoors or exposed to wind, rain
water spray or drips). Installing it in the coolest area of the room will save energy
consumption and running costs.
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | info@tempo.org
6
Product Overview
Scope of delivery
A Parts list
1 Freezer door balconies (4)
2 Covered freezer drawer
3 Covered fridge vegetable crisper
4 Levelling feet
5 Fridge door balconies (3)
6 Water tank
7 Removable fridge shelves (4)
8 Removable freezer shelves (4)
B Documentation (not shown)
Instruction manual
Warranty certificate
NOTE:
Due to continued product improvement, images and illustrations in this manual may
vary slightly from the product purchased. All images in this manual are for reference
purposes only. Parts are not necessarily pictured to scale.
1
2
4
3
5
6
78
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | info@tempo.org
7
Installation
Unpacking
• Packaging materials: This product has been packaged to protect it against
transportation damage. Remove all packaging materials from around and inside the
appliance and keep the original packaging carton and materials in a safe place. It
will help prevent any damage if the product needs to be transported in the future,
and you can use it to store the appliance when it is not in use. In the event that the
carton is to be disposed of, please recycle all packaging materials where possible.
Plastic wrapping can be a suffocation hazard for babies and young children, so
ensure all packaging materials are out of their reach and disposed of safely.
• Parts: Check to ensure you have all the parts listed in the Product Overview section.
• Damage: When unpacking, check the appliance carefully for damage. If it is
damaged, do not install the appliance. Contact our after sales support centre for
advice on examination or return of the damaged appliance.
• Power cord: Unwind the power cord to its full length and inspect it for damage.
Do not use the appliance if the appliance or its cord have been damaged or are
not working properly. In case of damage, contact our after sales support centre for
advice on examination, repair or return of the damaged product.
• Read the manual: Before installing your new fridge, read all safety instructions,
especially the sections on installation and electrical safety on pages 4–5. Installation
instructions follow on the next pages.
• Clean: Make sure the appliance is disconnected from the power supply before
cleaning the interior. Remove any tape that secured drawers, trays and shelves
during transport. Clean the interior surfaces and all internal accessories with
lukewarm water, a soft cloth and a neutral/mild soap/detergent. This will remove
any dust from transit and storage and help remove the typical smell of a brand new
product. Then dry thoroughly.
CAUTION: Do not use harsh or abrasive detergents or powders as these will
damage the finish.
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | info@tempo.org
8
Installation (Cont.)
Space requirements
• Door opening: Place the unit so there is enough space for the doors to open easily.
• Clearances: Ensure that air can circulate freely around the back of the cabinet,
which is necessary to cool the compressor and condenser. Allow at least 100mm
clear space at the back of the unit (Fig. 1) and 50mm at the sides (Fig. 2).
• Overhanging wall units: To ensure best performance, if the appliance is positioned
below an overhanging wall unit, the minimum distance between the top of the
cabinet and the wall unit must be at least 100mm. Ideally, however, the appliance
should not be positioned below overhanging wall units.
Moving and levelling the appliance
The appliance must be installed level so that it can work properly and the magnetic
door seals are properly aligned. It has four wheels for easy manoeuvrability and
adjustable feet for levelling the unit (Fig. 3).
Fig. 1
From factory:
• Wherever possible the spacers of the
product should be against a wall to
avoid touching or catching warm parts
(compressor, condenser) to prevent
possible burn.
Fig. 2
1400mm
1200mm
Wheel Levelling foot
Fig. 3
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | info@tempo.org
9
Fig. 4
Turn the levelling feet clockwise to raise or anticlockwise
to lower the front of the cabinet.
Doors
Electrical connection
• WARNING! It must be possible to disconnect the appliance from the mains power
supply; the plug must therefore be easily accessible after installation.
• Before plugging in your new fridge, let it stand upright for at least 4 hours.
This will allow the refrigerant gases to settle into the compressor and reduce the
possibility of a malfunction in the cooling system.
• The appliance must be earthed. The plug of the power supply cord is equipped
with a contact for this purpose. Do not under any circumstances cut or remove the
third (earth) prong from the power cord. If the plug does not fit your outlet, please
consult a licensed electrician for advice to have the outlet changed.
• Plug the unit into a dedicated, properly installed and earthed wall outlet. Ensure
that your outlet voltage and circuit frequency correspond to the voltage stated on
the appliance rating label.
• Secure the power supply cord behind the unit. Do not leave it exposed or dangling
to prevent injury and accidental disconnection from the power supply.
Installation (Cont.)
• To move the unit, tilt it slightly backward onto its wheels.
• To level the unit, adjust the levelling feet at the base of the cabinet (Fig. 4).
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | info@tempo.org
10
Control panel buttons and display
The control panel (Fig. 5) is located on the outside door of the freezer compartment.
It enables you to view and adjust the temperature in the fridge and freezer
compartments, select an operation mode or lock the control panel.
• The control panel display lights up for two minutes once the door of the fridge or
freezer compartment is opened (one door signal is sensed at a time), or when any
control is pressed.
• On first connection, the display shows the factory default (preset) temperatures for
the fridge and freezer compartments. During normal operation, the temperature
displays of the fridge and freezer compartments indicate the temperature of the
current settings.
• The control panel will be locked automatically 25 seconds after the last control
panel operation, and the control panel illumination will extinguish two minutes
thereafter.
Instructions
Fig. 5
Tabla de contenidos
Otros manuales de Refrigerador de Akai
Akai
Akai AK-269-TM Manual de usuario
Akai
Akai AK-323-BMB Manual de usuario
Akai
Akai AK-473-FF Manual de usuario
Akai
Akai AK-357-BM Manual de usuario
Akai
Akai AK-331-UF Manual de usuario
Akai
Akai AK-H470FF Manual de usuario
Akai
Akai AK-413-TMWD Manual de usuario
Akai
Akai AK-323-BM Manual de usuario
Akai
Akai ICE104S Manual de usuario
Akai
Akai AK-339-UF Manual de usuario
