AJA FS2 Manual de usuario

Quick Start Guide

Installation Summary

These instructions can help you connect and operate the FS2 quickly. For additional

details, please see the FS2 Installation and Operation Guide on the supplied DVD.

1. Unpack the shipping box, and read the late-breaking news sheet, if any.

2. Install physical options, such as fiber optic modules or Dolby Decoder card (Dolby

Encoder is a future option). AJA Fiber I/O modules slide into the Fiber slots in the

back; use only AJA modules. The Dolby Decoder card mounts inside the top cover

in the right-hand slot as shown below.

3. Mount the physical chassis: front rack, rear rack, or deskmount—1 RU x 17.5 inches

(44.45 cm) x 16 inches (40.65 cm). Do not block air flow through the side vents.

4. Connect one or two power cords to the FS2 and mains AC (100-240 VAC, 50/60 Hz,

55 Watts). For redundancy, use both cords and connect them to separate branch

circuits. The FS2 power supply is autosensing and adjusts to the available power.

5. Connect your computer to the FS2 using a CAT5 Ethernet cable to the FS2 RJ45 10/

100/1000 Ethernet LAN connector. You can connect directly or via a network

device such as a switch, hub, bridge, etc. The FS2 automatically senses and adjusts

to either a straight-through or crossover cable.

6. Make signal I/O connections to the FS2 back panel as the following figure shows.

Remove cover screws

Standoffs

Connectors

FS2 Top View

Dolby E Decoder

Option Card

Dolby E Encoder

(future) Option Card

Configuration Summary

The following instructions summarize how to configure the FS2 to communicate over the

web and initially pass video and audio. Using the front panel or browser menus described

later in this guide, you can adapt your FS2 configuration to your specific needs.

1. To begin establishing Ethernet communication so you can use a web browser with

the FS2, check that the IP Config menu is set to DHCP for automatic IP addressing:

Press the FS2 CONFIG button and turn the SELECT knob to display menu 2.1 IP

Config, which should read, DHCP. This setting is the most common and allows your

network to automatically set up FS2 IP addressing. If you prefer to manually set up

addressing, turn the ADJUST knob to change the setting to Static Addr.

2. Next, turn the SELECT knob to display menu 2.2 IP Address and write down the

address if you are using DHCP to automatically assign the address. Later, you will

enter this address in your browser address field to view the FS2 browser menus.

If the FS2 cannot automatically get an address or if you selected Static Addr, the IP

address defaults to 192.168.0.2.

To change the static address, push ADJUST momentarily, and then turn it to

change the blinking octet value. Turn SELECT to advance through the values and

use ADJUST to change each one. When finished setting all octet values, push

ADJUST momentarily to save. To revert at any time to the default address, hold

down ADJUST until the address resets.

Serial Digital

In/Out BNC

(3G/SD/HD)

Composite

In/Out BNC

10/100/1000

RJ45 Ethernet

LAN Connector

GPI 15-pin

DB-15F Connector

LED

RS422 Machine

Control 15-pin

DB-15F

(Future Upgrade)

External Reference

I/O with looping

BNC connectors.

Use 75-ohm terminator

on unused connector

or downstream equipment.

AC Power

Socket #2

Autosensing

100 to 240VAC

50/60Hz

AC Power

Socket #1

Autosensing

100 to 240VAC

50/60Hz

Component

YPbPr and

RGB or

Composite (v1.1)

In/Out

BNC

Analog Audio In/Out

Channels 1 through 8

DB-25F Connectors

(uses Tascam-style

cable)

AES/EBU Digital

Audio In/Out

Channels 1 through 16

DB-25F Connectors

Serial Digital

Fiber In/Out

(3G/SD/HD)

HDMI

In/Out

15 11

Ground

RS-422 Machine Control Output +

RS-422 Machine Control Input -

RS485 Dolby Metadata Output -

Ground

RS-422 Machine Control Output -

RS-422 Machine Control Input +

RS485 Dolby Metadata Output +

Ground

RS-485 Dolby Metadata Input -

RS-485 Dolby Metadata Input +

Ground

G - +G - +G - +G - +G - +G - +G - +G - +

G = Ground

+/- = Balanced Pair

Key

Audio Connector Pinout

15 11

Ground

GPI In 1

GPI In 2

GPI In 3

GPI GND 1

GPI GND 2

GPI In 4

GPI Out 1

GPI Out 2

GPI GND 3

GPI GND 4

GPI Out 3

GPI Out 4

Ground

GPI Connector Pinout RS422 Connector Pinout

FS2 Quick Start Guide — Display Menu Summary

You can skip this step if you are using DHCP. If you selected Static Addr in step 1,

turn the

SELECT knob to display menu 2.3 Subnet Mask. Change this to match the

Subnet Mask setting in your computer's Network panel/preferences, using the same

procedure described above in step 2 to change the static address.

You can skip this step if you are using DHCP. If you selected Static Addr in step 1,

turn the

SELECT knob to display menu 2.4 Default Gateway. Change this to match the

Gateway Address setting in your computer's Network panel/preferences, using the

same procedure described above in step 2 to change the static address.

5. Open a web browser on the computer connected to the FS2 and enter the FS2 IP

address in the browser's address field.

When the browser connects, the FS2 Status

menu screen appears (shown in “Web Browser Menu Summary” on page 4).

6. Configure video and audio I/O as explained in Quick Workflows, “Video and Audio

Right Out of the Box” on page 6, and test the FS2.

If the FS2 is working, configure it for your environment using the menu system. The

following pages summarize the menus, and the FS2 Installation and Operation Guide

on the supplied DVD describes the menus in detail. You can also contact AJA

Technical Support for assistance; please see the contact information at aja.com.

Display Menu Summary

The following illustration and table summarize front panel display operation.

Param number & name

Current Setting

Menu group & status

Info or Prompt

Turn the Select knob to scroll

through parameter menus.

Push Select to undo changes.

SELECT ADJUST

14.1 Output Timing H

SDI 1 1080i59.94

Use buttons to select

a Menu Group

Status Config System Video 1 Video 2

Remote Preset Output Audio1 Audio 2

Parameter Menu

Current Setting

Menu Group & Status

Info or Prompts

Tu r n Adjust to

change current setting.

Hold down Adjust to

restore default value.

Menu Group Purpose Parameter Descriptions

STATUS

Status and Error Conditions • Status of Video 1, Video 2, Caption, Reference, GenLock,

Power, Temperature , and Alarms

REMOTE

FS2 Control Method • Local front panel, Remote, or Local and Remote Control

• GPI Input and Output behavior

CONFIG

FS2 Configuration • IP and SNMP settings, MAC address

• Alarm Control

• Hidden Menu Access and Display Intensity (brightness)

• System Name

• System Serial Number and Software Version

• System Reboot

Web Browser Menu Summary

The following figure and table summarize web browser menu operation. The

settings generally correspond to the front panel display parameters, providing you

two methods of controlling the FS2. To see the equivalent front panel display

parameter number, hover the cursor over a setting.

PRESET

Preset Memory Registers • Store and Recall Presets

• Factory Preset (recall all defaults)

SYSTEM

Video and Audio Input and

System Settings

• Video and Audio Input Format settings, including 3G input

• Genlock Reference selection; Frame Rates

• NTSC Standard, HDMI and AES sample rate conversion

• Downconversion for HD in to analog composite out

• System Defaults

• Dolby Settings

OUTPUT

Output Sources • Video and Audio Output selections, including 3G output

VIDEO 1 & 2

Video Processor Inputs, Format,

Conversion Selections and

Adjustments

• Input Sources, background fill, Loss of input setting

• SD input upconversion, HD input downconversion

• Aspect Ratio, Region of Interest, H and V timing

• Output Format

• Matte, Proc Amp, Color Corrector, and Legalizer settings

• AFD embedding, input scan (i or p), captioning settings

• Test Pattern selection, Freeze Output

AUDIO 1 & 2

Audio Processor Input Selection

and Adjustments

• Audio input, format, and Audio Follow Video (AFV) selections

• Audio channel and stereo mapping

• Audio level, phase, and delay adjustments

• Audio signal generator selection

• Dolby Timing

FS2 Status and Menu Display Area

List of FS2 Menu Screens

Click a screen's

FS2 Alarms

System info, and FS2 Systems on the network

name to display it.

Click the gear

icon in the headng

to open the alarm menu.

The Network menu also

opens by clicking the gear.

Browser Screen Purpose Available Settings

ALARM CONFIG

Alarm Configuration • Alarm control

NETWORK CONFIG

Network Configuration • IP address, Subnet Mask, Default Gateway, System Name

FS2 Quick Start Guide — Web Browser Menu Summary

STATUS

Status and Error Conditions • Status of Video 1 Input, Video 2 Input, Video Input Format,

Video Output Format, GenLock Source, Proc Amp, RGB Color

Corrector

SYSTEM

Video and Audio Input and

System Settings

• Component & Composite Video In/Out Format (SMPTE/Beta)

• 3G Input Settings

• Analog Audio Standard (input/output levels)

• Genlock reference selection

• Frame Rates, NTSC Standard

• Composite Downconversion

• HDMI RGB Range, HDMI Sample Rate Converter Bypass

• AES/EBU Sample Rate Converter Bypass

• Dolby Settings

CONFIG

Configuration • Display intensity (brightness)

• Show/Hide unused menus

• UPnP Host & Proxy

PRESETS

Preset Memory Registers • Store and Recall Presets

• Export and Import Preset Files

• Name Each Preset register

• Recall Factory Preset (recall all default values)

OUTPUT

Output Sources • Video and audio output selections and formats

• 3G Output selection

VIDEO 1 & 2

Video Processor Inputs, Format,

Conversion Selections and

Adjustments

• Input Sources

• Output Format and Mode

• Background Fill, Loss of Input settings

• Conversion settings: Up, Down, Aspect, Edge, Custom

• Matte settings

• Proc Amp, Color Corrector

• Custom positioning

• Region of Interest

• H & V output timing

• Legalizer settings

• AFD embedding

• Scan Format (i or p)

• Caption settings

• Test Pattern Video Output, Freeze Output

AUDIO 1 & 2

Audio Processor Input Selection

and Adjustments

• Audio Processor input selection, format

• Audio channel and stereo mapping

• Audio embedding

• Audio Follow Video (AFV)

• Audio level, phase, and delay adjustments

• Audio Signal Generator selections

• Dolby Timing

REMOTE

Remote Control and GPIs • Local and/or remote control settings

• GPI Input and Output configuration

FIRMWARE

Firmware Update • Browse, select, and install firmware updates

Quick Workflows

The following workflows will help you quickly put the FS2 to use and get the most value.

CannedPresets

to Give You a

Quick Start

AJA plans to create a variety of preset configurations you can import and use to recall the

FS2 to commonly used configurations. This may save you considerable time compared to

setting up configurations manually. You will find these presets on the aja.com FS2 web

page when they become available:

http://www.aja.com/support/converters/converters-fs2.php

Additionally, the following workflows are provided to help you quickly do manual setups.

Video and

Audio Right

Out of the Box

The following quick workflow enables you to get video and audio through the FS2 as

soon as you get it out of the box and make video connections. In the following

procedures, where the terms select and adjust are used, turn the Select and Adjust knobs.

The factory setup is:

• SDI 1 Input feeds Video Proc 1 feeds SDI 1 Output.

• SDI 2 Input feeds Video Proc 2 feeds SDI 2 Output.

The parameter settings are:

• Output Format set to Follow Input.

• Video Input set to SDI 1 and SDI 2.

• Frame Rate set to 59.94/23.98.

• Genlock source set to Reference.

The menu operations for this setup are:

1. Press the Video 1 button.

a. Select 2 Output Format, and adjust to Follow Input.

b. Select 1 Video Input, and adjust to SDI 1.

2. Press the Video 2 button.

a. Select 2 Output Format, and adjust to Follow Input.

b. Select 1 Video Input, and adjust to SDI 2.

3. Press the System button.

a. Select 8 Genlock source, and adjust to Reference.

b. Select 9 Frame Rates, and adjust to 59.94/23.98.

4. Press the Output button.

a. Select 1.1 SDI 1 Video Out, and adjust to Video Proc 1.

b. Select 1.2 SDI 2 Video Out, and adjust to Video Proc 2.

5. Cable the SDI video into the SDI 1 & SDI 2 inputs.

6. Monitor any output for video and audio.

FS2 Quick Start Guide — Quick Workflows

SDI 1 Test

Signal Outputs

The following two workflows produce bars and tone outputs and ramp and silence outputs

The setup is:

• Test signals are switched in at the FS2 outputs, so no particular input settings are

required.

The parameter settings are:

• No settings required.

Menu operations for SDI 1 Out Bars and Tone:

1. Press the Video 1 button.

2. Select 3 Video 1 Output Mode, and adjust to Test Pattern.

3. Select 21 Video 1 Test Pattern Video and adjust to 75% Bars.

4. Press the Audio 1 button.

5. Select 4 Audio Signal Gen and adjust to 1 kHz tone.

Menu operations for Ramp and Silence:

1. Press the Video 1 button.

2. Select 3 Video 1 Output Mode, and adjust to Test Pattern.

3. Select 21 Video 1 Test Pattern Video and adjust to Ramp.

4. Press the Audio 1 button.

5. Select 4 Audio Signal Gen and adjust to Off.

Sidebar Video

The following quick workflow shows you how to create sidebar edges filled with video.

The setup is:

• SDI 1 Input feeds Processor 1 foreground.

Use an SD 525 input on SDI 1; it will be upconverted to 1080i59.

• SDI 2 Input feeds Processor 2, which will provide Processor 1 background.

Use an HD input signal in SDI2.

• Processor 1 feeds SDI1 Output (center video with sidebar video).

• Processor 2 feeds SDI2 Output (showing the sidebar video signal alone).

The parameter settings are:

• Video 1 Input set to SDI 1.

• Output Format set to 1080i59.94.

• Video Output Mode set to Normal.

• Upconvert Mode set to 4x3 Pillar.

• Custom Size/Pos set to Off.

• Background Fill set to Video 2.

The menu operations for this workflow are:

1. Press the Video 1 button.

a. Select 1 Video 1 Input, and adjust to SDI 1.

b. Select 2 Output Format, and adjust to 1080i59.94.

c. Select 3Video Output Mode, and adjust to Normal.

d. Select 6 Upconvert Mode, and adjust to 4x3 Pillar.

e. Select 4 Background Fill, and adjust sidebar video to Video 2.

e. Select 9 Sidebar Edge, and adjust sidebar position as you prefer.

g. Select 13.0 Custom Size/Pos, and adjust to Off.

2. Press the Video 2 button.

a. Select 1 Video 2 Input and adjust to SDI2.

b. Select 2 Output Format and adjust to 1080i59.94.

FS2 Quick Start Guide — Quick Workflows

Picture Overlay

The following workflow shows how to create a video box overlaying another video source.

The setup is:

• Video Processor 1 input set to SDI 1 (any format).

The parameter settings are:

• Video 1 Input set to SDI 1.

• Output Format set to 1080i59.94.

• Video Output Mode set to Normal.

• Upconvert Mode set to 4x3 Pillar.

• Custom Size/Pos set to On.

• Custom Size, Aspect, H&V Position, Left/Right/Top/Bottom Crop as preferred.

The menu operations for this workflow are:

1. Press the Video 1 button.

a. Select 1 Video 1 Input, and adjust to SDI 1.

b. Select 2 Output Format, and adjust to 1080i59.94.

c. Select 3 Video Output Mode, and adjust to Normal.

d. Select 6 Upconvert Mode, and adjust to 4x3 Pillar.

e. Select 13.0 Custom Size/Pos, and adjust to On.

f. Select 13.1 Custom Size, and adjust to10% to 200%.

g. Select 13.2 Custom Aspect, and adjust aspect ratio as preferred.

h. Select 13.3/13.4 Custom H Pos/Custom V Pos, and adjust H & V box position.

i. Select 13.5–13.8 Custom Left/Right/Top/Bottom Crop, and adjust box edges.

Letterbox Top

The following workflow downconverts a 1080i SDI input, using Letterbox mode, and

shifts the letterboxed video to the top of the screen, leaving the bottom of the screen

available.

The setup is:

• SDI1 input feeds Processor1 Foreground

• Use an HD (1080i) input signal on SDI1, which will be downconverted to 525i.

• Processor 1 feeds SDI1 Output.

• Downconvert Mode is set to Letterbox. Custom V Pos is set to 12.5% to shift the

letterbox to the top of the screen.

The menu operations for this workflow are:

1. Press the Preset button.

a. Select 3 Factory Preset.

b. Hold down the ADJUST knob for three seconds.

2. Press the Video 1 button.

a. Select 1 Video 1 Input, and adjust to SDI 1.

b. Select 2 Output Format, and adjust to 525i59.94.

c. Select 3 Video Output Mode, and adjust to Normal.

c. Select 4 Background Fill, and adjust to Matte.

d. Select 7 Downconvert Mode, and adjust to Letterbox.

e. Select 13.0 Custom Size/Pos, and adjust to On.

f. Select 13.4 Custom V Pos, and adjust to 12.5%.

g. Optional: To fill the bottom portion of the screen with video, select 4 Background

Fill, and adjust to Video2 (ALARM LED will light).

3. Press the Video 2 button.

a. Select 2 Output Format, and adjust to Follow Video1 (ALARM LED will

extinguish).

Otros manuales para FS2

Tabla de contenidos

Otros manuales de Equipo de grabación de AJA

AJA

AJA FS1-X Instrucciones de funcionamiento originales

AJA

AJA Io 4K Plus Instrucciones de funcionamiento

AJA

AJA Ki PRO rack Manual de usuario

AJA

AJA IOExpress Instrucciones de funcionamiento

AJA

AJA FS2 Manual de usuario

AJA

AJA Ki PRO ULTRA Instrucciones de funcionamiento originales

AJA

AJA ioXT Manual de instrucciones

AJA

AJA Io Express Instrucciones de funcionamiento

AJA

AJA OG-3GDA Series Instrucciones de funcionamiento

AJA

AJA T-TAP Instrucciones de funcionamiento originales

AJA

AJA io4K Manual del propietario

Manuales populares de Equipo de grabación de otras marcas

KV2 Audio

KV2 Audio 500 Series Manual de usuario

Robotics Technologies

Robotics Technologies microBus-Cam II Manual de usuario

Seca

Seca 460 Manual de usuario

Cognex

Cognex MVS-8000 Series Manual de usuario

Mect

Mect MPNC006 Series Manual de usuario

Bad Caf

Bad Caf THE LEASH Manual de usuario

Strymon

Strymon NIGHTSKY Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario

Tews Technologies

Tews Technologies TPMC465 Manual de usuario

Honeywell

Honeywell Excel 50 Manual de usuario

SeaLevel

SeaLevel COMM+8.LPCI Manual de usuario

Arturia

Arturia AUDIOFUSE STUDIO Manual de usuario

Rukra

Rukra RK-1240 Manual de usuario

Samson

Samson SCOM Manual de usuario

Dynacord

Dynacord DPS260 Manual de usuario

Nice

Nice Core Manual de usuario

Pyle Pro

Pyle Pro PSS8 Manual de usuario

RF-System

RF-System TinyGate Manual de uso y cuidado