Aiwa TV-F2000 Manual de usuario

SERVICE MANUAL

DATA

COLOR TELEVISION

TV-F2000

TV-F2100

HT,NH

S/M Code No. 09-009-432-1S2

SUPPLEMENT

•This Service Manual contains the additional information

“DISASSEMBLY INSTRUCTIONS” and “ADJUSTMENT”

for the model TV-F2000 (U) / TV-F2100 (HT,NH).

If requiring the other information, see Service Manual of

TV-F2000(U), (S/M Code No. 09-006-432-1R1) and

TV-F2100(HT,NH), (S/M Code No. 09-008-432-1R2).

– 2 –

NOTICES BEFORE REPAIRING

• Do not turn on the power without degaussing coil when repairing.

• In case of removing degaussing coil when repairing, connect dummy as follows;

Method 1 : Use another new degaussing coil and connect it when repairing.

Method 2 : Place the 6.8Ω- 20W resistor to the degaussing coil connector and connect it as service jig.

• Cement resistor R848, which is parallel to the degaussing coil, is opened when the power is turned on without the degaussing coil or dummy resistor.

This model’s cement resistor, R848 is as shown below.

Horizontal noise will appear on the screen if this cement resistor has been opened.

• If there is no instruction for setting of the input signal, get signal from line input (LINE-IN).

Model name

TV-F2000 / F2100

R848

56Ω/ 2W

Type

Cement Resistor

– 3 –

Anode cap

CRT GND

Hook CRT

CRT GND

Grip

DISASSEMBLY INSTRUCTIONS

1. REAR CABINET REMOVAL

Figure 1-1

2. HIGH-VOLTAGE CAP (ANODE CAP) REMOVAL

2-1. Cautions before Removing

Discharge the anode voltage

(1) The anode voltage is not discharged completely from the

CRT of this unit even after the power is turned off. Be

sure to discharge the residual anode voltage before

removing the anode cap.

Do not use pliers

(2) Do not use pliers, etc. to remove the anode cap. If you

used pliers and bent the hook to remove the cap, the spring

characteristics of the hook could be lost, and when

reinstalled, the cap would come off from the CRT anode

button easily, causing an accident.

Do not turn the anode cap

(3) If the anode cap is turned in the direction of its

circumference, the hook is likely to come off.

2-2. Anode Cap Removal

Discharge the anode voltage. (See Figure 2-1)

(1) Connect a flat-bladed screwdriver to the CRT GND via

an alligator clip.

(2) Use a tester to check the end of the screwdriver and ground

of the TV for continuity.

(3) Touch the hook with the end of the screwdriver.

Caution : Be careful not to damage the anode cap.

(4) Turn over the anode cap.

Caution : Be careful not to damage the anode cap.

Figure 2-1

Figure 2-2

Anode cap

CRT

Hook

Anode button

(1) Remove four screws 1and three screws 2, then

remove the rear cabinet in the direction of the arrow.

(See Figure1-1)

Front cabinet

Rear cabinet

–4 –

(5) Push the anode cap with your thumb in the direction of

arrow 1as shown in the figure, then lift the cap in the

direction of arrow 2to release the hook on one side.

(See Figure 2-3)

(6) Turn over the anode cap on the side where the hook was

released and pull out the cap in the direction opposite to

that on which the cap was pushed. (See Figure 2-4)

Caution : Do not pull out the anode cap straight up.

:Do not pull the cap forcibly. After removing

the cap, check that the hook is not deformed.

Figure 2-3

3. ANODE CAP REINSTALLTION

Observe the cautions carefully so that no accident occurs

due to a defect in installing the anode cap and so it does

not come off.

3-1. Caution before Reinstalling

Never turn the anode cap after installing it

Never re-use the hook when it has been deformed

(1) If the anode cap is turned after it is installed, it may come

off. Therefore, arrange the high-voltage cable before

attaching the anode cap. (See Figure 3-1)

(2) If you have attached the anode cap before arranging the

high-voltage cable, arrange the cable carefully so the cap

does not turn.

3-2. Anode cap reinstallation

(1) Use a clean cloth moistened slightly with alcohol to clean

the installation section. (See Figure 3-2)

Caution : Check that the installation section is free from

dust, foreign matter, etc.

(2) Coat the anode cap installation circumference with an

appropriate amount of the specified silicone grease (KS-

650N).

Caution : Be careful that silicone grease does not enter

the anode button.

CRT CRT

Anode cap

Hook Hook

Anode cap

Hook

Anode button

CRT

Left Right

Anode cap

Anode button

Installation

section

Figure 2-4

Figure 3-1

Figure 3-2

–5 –

(3) Eliminate twisting, etc. of the high-voltage cable and

arrange it so that no twisting occurs. (See Figure 3-3)

Caution : If the cable is not arranged correctly, the anode

cap could turn and cause an installation defect.

(4) Turn over the rubber cap symmetrically on the left and

right. (See Figure 3-4)

Caution : Take great care not to damage the anode cap.

Figure 3-3

(5) Fit your forefinger over the projection at the center of the

cap and hold the cap between your thumb and middle

finger. (See Figure 3-5)

High-voltage cable Anode cap

Figure 3-4

Figure 3-5

–6 –

(6) Apply the hook on one side to the anode button as shown

on the figure. (See Figure 3-6)

Caution : Check that the hook is held securely.

(7) Apply the hook on the other side to the anode button as

shown in Figure 3-7.

(8) Pull the anode cap slightly with the rubber cap turned

over and visually check that the hook is engaged securely.

(9) Release your hand from the rubber cap of the anode cap.

Caution : Cover the anode cap so that it does not lift.

(10) Hold the skirt of the andoe cap slightly to improve the

close contact between the cap and CRT.

(11) Check that the anode cap is in close contact with the CRT.

(See Figure 3-8)

Figure 3-8

Figure 3-7

Figure 3-6

Anode button

Skirt

Hook

Anode button

Hook

Anode button

Hook

30°

– 7 –

Figure 4-1

4. NK C.B REMOVAL

(1) Disconnect CN903 (CRT GND).

(2) Disconnect CN901, CN902, CN951, CN952.

(3) Remove the NK C.B. in the direction of arrow 1.

(See Figure 4-1)

5. MAIN C.B REMOVAL

(1) Remove connector (CN404) from Audio C.B.

(2) Remove connector (CN807).

(3) Remove connector (CN882) from PS C.B.

(4) Pull out the MAIN C.B. in the direction of the arrow 2

(See Figure 4-1).

CN882

(Power Cord)

Front cabinet

AUDIO C.B

CN404(Speakers)

CN951

NK C.B

CN901

CN903

CN807

(Degauss

cord)

CN902

CN952

MAIN

C.B

–8 –

Color bar signal of a pattern generator

Precautions Before Starting Adjustment

Satisfy the following setting conditions before starting adjustment.

• Allow warm-up of 20 minutes or longer. (Do not turn off during

warm-up.)

• Set all picture quality controls of users' setting to initial set-up,

unless otherwise specified.

• Picture quality reset

1. Select "Picture" on the screen menu and press enter button.

2. Select "Normal" and press enter button.

3. Select "Reset" and press enter button.

• Set the pattern generator’s output level to 1.0Vp-p (across 75Ω

load).

Because the video signal output from a pattern generator is used as

the adjustment signal input during adjustment, the video signal

output from the pattern generator must conform with the

specifications. Measure the output waveform across 75 Ωload.

Confirm that the synchronizing signal has an amplitude of about

0.3 V, the video signal portion has an amplitude of about 0.7 V and

the burst signal has an amplitude of about 0.3 V with flat envelope.

Confirm that ratio of the burst signal amplitude and the red signal

amplitude is 0.30 : 0.66. If the output signal does not conform with

the specifications, calibrate the pattern generator. (Refer to pattern

generator operation manual.)

Use the LEADER: LCG 404 for the pattern generator.

Fig. 1-1

Approx.

0.3V

Approx. 0.3V

Burst signal

1 Vp-p

White (Approx.

75%)

Approx. 0.7V

Yellow

Cyan

Green

Magenta

Red

Blue

Black

75% white

TV display

1-1. Precautions

(1) Receive the white raster signal, and then perform aging for at

least 20 minutes.

(2) Demagnetize the area surronding the CRT with a degausser

before making adjustments.

(3) Set the picture quality for each mode to the factory setting.

(4) Position the front screen facing the east as much as possible.

1-2. Purpose

(1) Beam landing adjustment (purity magnet)

Set the left/right balance of beam landing. If there is a

discrepancy in this adjustment, a color irregularity will occur.

After completion of the landing adjustment, it is necessary to

perform convergence adjustment.

Color

irregularity

Color

irregularity

Before adjustment After adjustment

ADJUSTMENT

Set-Up For Adjustment 1. CRT Adjustment

–9 –

(2) Beam convergence adjustment (4-pole magnet)

Align the R beam with the B beam. The G beam does not

move with this adjustment.

R/B

Align the R beam with the B beam

Fig. 1-2

(magenta)

(4) The composition of each magnet is as shown in Fig. 1-4.

In making adjustments, rotate the lock ring clockwise (looking

from the CRT’s back screen) and disengage.

Be careful not to loose the lock ring too much. If the magnet

assembly has become shifted during adjustments, secure it to

the position in Fig. 1-4.

(3) Beam convergence adjustment (6-pole magnet)

With a 4-pole magnet align the G beam with the already aligned

R/B beam.

R/B

RGB

(magenta)

(white)

Align the G beam with the R/B beam

Fig. 1-3

CRT DY

DY lock screw Purity 4-pole 6-pole Lock ring

NK C.B

Magnet assembly

Fig 1-4

Magnet assembly

lock screw

–10 –

(1) Receive the green raster signal from the pattern generator.

(2) Loosen the magnet lock screw, and shift the magnet assembly

backward (toward the neck).

(3) Loosen the DY lock screw, and shift the DY deflecting yoke

backward (toward the neck).

(4) After opening the two purity magnets to the same angle, adjust

the color width of the bands on both sides of the screen so that

they are equal. (refer to Fig. 1-5 (a)).

As shown in Fig. 1-5 (b), the purity magnet functions in

relation to the electron beam.

(5) Gradually shift the deflecting yoke toward the front (toward

the CRT funnel). Stop movement at the point when the screen

has become completely green.

(6) Also, verify the respective monochromatics of red and blue.

(7) While looking at the screen, adjust the tilt of the deflecting

yoke and tighten the DY lock screw.

(8) Shift the magnet assembly to the front (toward the CRT funnel),

stop movement before the adjustment position and then tighten

the magnet lock screw.

At this time, be careful not to shift the position of the purity

magnet.

As there is occurrence of convergence distortion after

completing the landing adjustments, be sure to carry out

convergence adjustments.

If the color irregularities in the screen’s corner section are

not improved, correct them with the landing magnet. After

using the landing magnet, be sure to demagnetize the CRT

with degausser and verify that there is no occurrence of color

irregularity. (refer to Fig. 1-6)

Landing magnet: 81-JTI-710-010

(two-sided adhesive tape) : 80-XVI-218-010 Cushion

Cushion

Landing magnet

Since the landing magnet is polarized,

check the screen’s improvement through

rotation, not only by position.

Fig 1-6

1-3. Beam Landing Adjustment

RGB

Fig 1-5 (a)

R=B

SN NS

NS SN

Fig 1-5 (b)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de TELEVISOR de Aiwa

Aiwa

Aiwa VX-C131U Manual de usuario

Aiwa

Aiwa TV-SE211 Manual de usuario

Aiwa

Aiwa TV-F2400 Manual de usuario

Aiwa

Aiwa TV-C142S Manual de usuario

Aiwa

Aiwa TV-20ST5 Manual de usuario

Aiwa

Aiwa TV-CN202 Manual de usuario

Aiwa

Aiwa VX-S135U Manual de usuario

Aiwa

Aiwa VX-T14G10 Manual de usuario

Aiwa

Aiwa TV-21ST3 ST Manual de usuario

Aiwa

Aiwa TV-FT2588 Manual de usuario

Aiwa

Aiwa TV-AR145 Manual de usuario

Aiwa

Aiwa VX-T149 Manual de usuario

Aiwa

Aiwa TV-A2019 Manual de usuario

Aiwa

Aiwa TV-S2700 Manual de usuario

Aiwa

Aiwa TV-FS2180 Manual de usuario

Aiwa

Aiwa TV-C202S Manual de usuario

Aiwa

Aiwa TV-AN145 Instrucciones de uso

Aiwa

Aiwa TV-SA2155 Manual de usuario

Aiwa

Aiwa VX-F20DV1 Manual de usuario

Aiwa

Aiwa TV-C202S Manual de usuario

Aiwa

Aiwa VX-T14SX7 Manual de usuario

Aiwa

Aiwa TV-AR295 Manual de usuario

Aiwa

Aiwa VX-F21DV1 Manual de usuario

Aiwa

Aiwa TV-F2100 Manual de usuario

Manuales populares de TELEVISOR de otras marcas

Philips

Philips Colour Television Manual de usuario

Toshiba

Toshiba 27A10 Manual de usuario

Philips

Philips 42PF9630A/37 Manual de usuario

Hitachi

Hitachi 32FX48B Manual de usuario

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Manual de usuario

Changhong Electric

Changhong Electric uhd55b6000is Manual de usuario

Philips

Philips Matchline 21CE7551 Manual de usuario

Panasonic

Panasonic Genus TX-G10 Manual de usuario

Toshiba

Toshiba 19A20 Manual de usuario

Philips

Philips 25PT4523-16 Manual de usuario

Sony

Sony XBR-100Z9D Manual de usuario

Philips

Philips PR0930X3 Manual de usuario

Philips

Philips Brilliance 231P4QPY Manual de usuario

Samsung

Samsung 55S9 B Series Manual de usuario

Philips

Philips 32HF9385D Guía de solución de problemas

Sharp

Sharp LC-40FI5012E Manual de usuario

Loewe

Loewe Table Stand Reference 55 Manual de usuario

Philips

Philips 32PFH5300 Manual de usuario