AIRTRONICS SD-10G Aero Manual de usuario
SD-10G AERO
Procedure for obtaining four different In-Flight Selectable Flight Modes using the SD-10G
Transmitter for controlling the Fun-Fly Ultra Stick type model with dual Flaps and
Ailerons.
Normal: No Mixing
Flight Mode 1: Takeoff, with Flaps in Down Position
Flight Mode 2: Elevator to Flap Mixing. Up Elevator causes the Flaps to go Down.
Down Elevator causes the Flaps to go UP.
Flight Mode 3: Aileron to Flap Mixing. Flaps work in the same direction as
the Ailerons.
Flight Mode 4: Crow. Ailerons go UP, Flaps go Down, with Flaps responding
to Aileron commands with Flap to Elevator Compensation.
NOTE: Prior to programming your SD-10G for a specific model, Use MODEL SELECT, to select a
specific AERO model as shown on page 29 of your instruction manual. BIND and set the SAFETY
LINK as indicated on page 21 of your instruction manual. The SAFETY LINK should match the
currently selected model.
Select SYSTEM using the Navigation Pad. Press the ENTER key.
Scroll down using the Navigation Pad and highlight MODEL NAME by pressing the ENTER key.
Enter a MODEL NAME as described on page 29 of your SD-10G manual. Press END when complete.
Scroll down using the Navigation Pad to TYPE. Press the ENTER key. Use the YES/+ and NO/- key to
select AERO. Use the Navigation Pad and the YES/+ and NO/- keys to make it read:
WING > NORMAL, AILERON >2, FLAP >2, TAIL >NORMAL, THROTTLE >1
Press the ENTER key to save the selection option> Press the YES/+ key to CREATE NEW DATA.
Press the END key.
Scroll down using the Navigation Pad and select CHANNEL ASSIGN. Press the ENTER key.
The Default SD-10G Channel Assignments for the above selections are as follows:
#1 Elevator
#2 Left Aileron
#3 Throttle
#4 Rudder
#5 Gear
#6 Right Aileron
#7 Left Flap
#8 Right Flap
#9 AUX 2
#10 AUX
Press the END key
Select SWITCH ASSIGN using the Navigation Pad Down arrow. Press ENTER.
Assign the following switches using the Navigation Pad and the YES/+ and NO/- keys.
FLIGHT MODE 1 >11 >or >--
2 >10 >or >--
3 >23 >or >--
- 2 -
FLIGHT MODE 4 >22 >or >--
GEAR >-- >or >--
Throttle Cut >34 > or >--
Flap 1 >11 >or >--
Flap 2 >22> or >--
EL > FL >10 >or >--
FL > EL >22 >or >--
C-MIX 1 >23 >or >--
C-MIX 2 >23 >or >--
C-MIX 3 >22 >or >--
C-MIX 4 >22 >or >--
C-MIX 5 >--- >or > --
Press the END key twice.
NOTE: Turn OFF each Flight Mode switch after completion of programming each function and Mix.
All values show are trial values. Fine tune after completion of programming your setup.
FLIGHT MODE 1—Takeoff with Flaps in Down Position
Select SURFACE using the Navigation Pad. Press ENTER
Turn ON Flight Mode 1 Switch (#11)
Press Navigation Pad Down arrow and select EPA. Scroll to the right and select the LF
Use the YES/+ key to input a value of 50%. Do the same for the RF.
The screen will show 1 50% indicating that FLAP 1 is used for this function. Note that polarity
determines the direction of servo throw and value the amount........... Press END key twice.
FLIGHT MODE 2 --- Elevator to Flap Mixing
Select F-MODE. Press ENTER
Turn ON Flight Mode 2 Switch (#10)
Scroll down to MIXING. Press ENTER
Scroll down to EL > FL. Press ENTER
Use the Navigation Pad and the YES/+ and NO/- keys to make it read:
F-MODE (2)
COMMON >SEP
EL >LF > 20%
EL >RF > 20%
Press the END Key twice.
- 3 -
FLIGHT MODE 3 ---Aileron to Flap Mixing
Scroll down to C-MIX. Press ENTER.
Turn ON Flight Mode 3 Switch (#23)
Select C-MIX 1.
Use the Navigation Pad and the YES/+ and NO/- keys to make it read and show a graphical display.
F-MODE(3)
COMMON>SEP
MASTER>AI
SLAVE > LF
Point 1 > -50%
Point 9 > +50%
Delay > 0%
Press the END key. Press ENTER.
Select C-MIX 2.
Use the Navigation Pad and the YES/+ and NO/- keys to make it read:
F-MODE (3)
COMMON>SEP
MASTER>AI
SLAVE > RF
Point 1 > -50%
Point 9 > +50%
DELAY > 0%
Press the END key. Press ENTER.
FLIGHT MODE 4 ---CROW
Select C-MIX 3.
**Turn OFF Flight Mode 3 and Turn ON Flight Mode 4 Switch (#22)
Use the Navigation Pad and the Yes/+ and NO/- keys to make it read:
F-MODE (4)
COMMON>SEP
MASTER>AI
SLAVE>LF
Point 1 > -75%
Point 9 > +75%
Delay > 0%
Press the END key. Press ENTER.
Select C-MIX 4.
Use the Navigation Pad and the YES/+ and NO/- keys to make it read:
F-Mode(4)
COMMON>SEP
MASTER>AI
SLAVE>RF
Point 1 > -75%
Point 9 > +75%
Delay > 0% Press the END key twice.
- 4 -
Use the Navigation Pad to select MIXING. Press the ENTER key.
Select FLAPERON –Press ENTER key. Flight Mode 4 Switch (#22) is still ON.
Use the YES/+ key and NO/- Keys to make the Flaperon Mix read as follow
F-MODE (4)
COMMON >SEP
ACT/INH > ACT
FL >LA 100%
FL >RA 100% Press END key.
Scroll down to FL>EL --Press ENTER key.
Use the YES/+ key and NO/- keys to make Flap to Elevator Compensation Mix read as follows:
F-MODE (4)
COMMON > SEP
FL > EL > + or – 10% Press END key three times.
Select SURFACE using the Navigation Pad. Press ENTER.
Press the Navigation Pad Down arrow and select EPA. Scroll to the right and select LF.
Use the Yes/+ key to input a value of 100%. Do the same for the RF
The screen will show 2 100% indicating FLAP 2 is used for this function. Note that polarity determines
the direction of the Flap servo throw and value the amount....Press the END key twice.
Note: Turn OFF each Flight Mode switch after completion of each of the Flight Mode mixes. The above
figures are trial values. Fine tune later. The value determines the amount of servo travel and the polarity
determines the direction of servo travel.
Jack R. Albrecht
Airtronics Technical Support
17 June 2009
Otros manuales para SD-10G Aero
6
Tabla de contenidos
Otros manuales de Mando a distancia de AIRTRONICS
AIRTRONICS
AIRTRONICS XL2P Manual de usuario
AIRTRONICS
AIRTRONICS VG4R Manual de usuario
AIRTRONICS
AIRTRONICS F3000 Manual de usuario
AIRTRONICS
AIRTRONICS Super EXZES Manual de usuario
AIRTRONICS
AIRTRONICS SD-5G Manual de usuario
AIRTRONICS
AIRTRONICS MX-V Manual de usuario
AIRTRONICS
AIRTRONICS SD-10G Aero Manual de usuario
AIRTRONICS
AIRTRONICS MX-Sport Manual de usuario
AIRTRONICS
AIRTRONICS SD-10G Aero Manual de usuario
AIRTRONICS
AIRTRONICS M11X Manual de usuario
AIRTRONICS
AIRTRONICS MT-4 Manual de usuario
AIRTRONICS
AIRTRONICS SD-10G Aero Manual de usuario
AIRTRONICS
AIRTRONICS Sanwa Aquila-6 Manual de usuario
AIRTRONICS
AIRTRONICS SD-10G Aero Manual de usuario
AIRTRONICS
AIRTRONICS MX-3X Manual de usuario
AIRTRONICS
AIRTRONICS RDS8000 FHSS Manual de usuario
AIRTRONICS
AIRTRONICS SD-10G Aero Manual de usuario
AIRTRONICS
AIRTRONICS MT-4 S Manual de usuario
AIRTRONICS
AIRTRONICS MT-S Manual de usuario
AIRTRONICS
AIRTRONICS M12 Manual de usuario
