Airquee Last One Standing Instrucciones de funcionamiento

Page 1of 14

Contents

1. Site Survey........................................................................................ 2

2. Inflatable Inclusions........................................................................... 3

3. Intended use of product .................................................................... 3

4. Operating guidelines......................................................................... 4

5. Troubleshooting................................................................................ 4

6. Hazards relating to electrical equipment ........................................... 5

7. Setup ................................................................................................ 5

7.1 Assembly of the mechanism..................................................... 6

7.2 Adding the sealed tube............................................................. 8

7.3 Assembly of the bed................................................................. 9

7.4 Assembly of the Control Panel.................................................10

7.4.1 The Control Box .............................................................10

7.4.2 Transporting and storing.................................................10

7.4.3 Positioning of the control panel.......................................11

8. Routine inspections, Trial Operations and Thorough Examinations ..11

8.1 Routine Inspections...................................................................11

8.2 Trial runs...................................................................................12

8.3 Thorough examination...............................................................12

9. Spare Parts Codes............................................................................12

Page 2of 14

Last One Standing

with Single Arm Mechanism

IMPORTANT

AS OWNER/OPERATOR IT IS YOUR RESPONSIBILITY TO WRITE AND CARRY OUT

YOUR OWN RISK ASSESSMENT BEFORE ATTEMPTING TO USE THIS PRODUCT.

1.Site survey:

1. Carry out a survey of the area where the Last One Standing will be located, and

check for any overhead/underground cables. It’s important that this is carried out

to avoid ground anchors penetrating underground services, and the Last One

Standing coming into contact with overhead cables when inflated.

2. You should provide an adequate power supply to the fan, this should adhere to

your local power regulations.

3. Check wind speed:The maximum wind speed should not exceed Force 5 on the

Beaufort scale of 28-38 kmph (19-24 mph). Force 5 is a fresh breeze when small

trees in leaf begin to sway.

2. Inflatable Inclusions:

Extra equipment needed in addition to what is supplied with your inflatable:

•Suitable 240v Power Supply to operate the fan

CAUTION! Precautions should be taken during handling and use

of the product to prevent electric shock. The blower requires a

Ground Fault Protected Circuit (GFCI). Please read the

manufacturer’s Instruction Manual before using the blower(s).

The inflatable

in its bag Anchor Pegs Land Operation

Manual Repair Kit

Page 3of 14

Extra equipment you could consider for your new inflatable:

•Ground sheet to protect the underside of your inflatable

•Sandbag covers to anchor your inflatable indoors

•Sack truck to move your inflatable safely

•RCD to attach to your extension lead

•Crash Mats

This inflatable can be set up and packed away by 3 persons who have had

proper manual handling training and use the correct equipment to move the

inflatable.

3. Intended use of the product:

4. Operating guidelines:

- Before entering the game area, CLEAR INSTRUCTIONS SHALL BE GIVEN to players

on their conduct during playtime:

- NO SOMERSAULTS or any ACROBATICS allowed.

- All players remove footwear, eye wear, cell phones, keys, neck wear and/or any

sharp items.

- DO NOT allow the users to OBSTRUCT THE MOVEMENT OF THE ARM. This

includes no hanging on the arm, pushing-pulling them.

- For safety reasons, users should only stand at the designated jumping space

(numbers, podiums). Do not allow them to get closer to the middle of the bed.

- No one with ANY PRE-EXISTING INJURIES OR HEALTH CONCERNS may

use the Last One Standing game.

- Every time a user falls THE MECHANISM MUST BE STOPPED!

- Use the Emergency Button only in a case of an emergency. After releasing it, WAIT AT

LEAST 5 SECONDS before pressing any other button on the Control Box.

- The MAXIMUM NUMBER OF USERS HAS TO BE RESPECTED at all times.

The Last One Standing with Single Arm Mechanism

is designed to be usedby up to eightplayers andone

operator. The players must jump at the right time to

avoid the rotating sealed arm. The operator has

control (via the supplied control panel) over the

speed and direction of the arm to make the game

harder or easier as required. If a user is knocked over

by the arm, they should exit the game. The operator

must stop the mechanism until the eliminated player

has exited the inflatable. The last player standing is

the winner.

Page 4of 14

- The unit should NOT TO BE USED IF IT BECOMES WET. In the event of rain, the unit

should be deflated and folded to prevent water collecting on it.

- The Emergency Stop button MUST ALWAYS BE DEPRESSED AND THE KEY

REMOVED whenever you are setting up the ride or leaving the control console

unattended.

- The operator must adjust the speed of the arm to the abilities of the players.

- Do not press more than one button at a time.

- If the arm is OBSTRUCTED, RELEASE the left-right rotation buttons IMMEDIATELY.

5. Troubleshooting:

Inside the control box there is a motion controller manufactured by Yaskawa. This electronic part

is responsible for the motion of the sealed arm. Any incorrect usage of the mechanism could result

in Yaskawa producing an Error Code, which means the mechanism stops responding to the

operator’s commands.

Most of these error codes are built in safety mechanisms, protecting the electric motor. When

experiencing this sudden stop, our advice is to follow these simple steps:

- Turn OFF the mechanism, then ON with the Main On/Off key. This will reset the

Yaskawa settings and you should be able to resume playing.

- If that doesn’t help, unlock the top of the Control Box with the supplied triangle key, and

reset the settings manually by pressing the RESET button. (see figure below)

CAUTION! TAKE EXTRA CARE WHEN OPENING THE CONTROL BOX.

DO NOT TOUCH ANYTHING ELSE BESIDES THE RESET BUTTON.

Issue

Steps to take

Short circuit or ground fault

on the drive output side:

Try connecting the motor directly to the main supply. In case it is

used with an extension cord, make sure not to connect to many

things to the same extension lead.

The motor is operated at low

speed with heavy load:

Make sure you remove the obstacle from the motor that keeps it

stopping. Please note you are not allowed to add anything to the

middle bar of the mechanism. Make sure that when a player is

on the sealed arm the mechanism is stopped and is not moving

forward.

Page 5of 14

If you still have issues with the mechanism, please contact Airquee

customer support on the following number +44 (0)1179 414 918.

To avoid getting an error code:

- Make sure the electric power supply is stable and not fluctuating in any way.

- Make sure all the cables are connected properly: the motor with the control box, and the

control box to the main electric supply.

6. Hazards relating to electrical equipment:

The use of portable electrical equipment involves the potential risk of electric shock, burns or fire. A

major cause of accidents is failure to maintain equipment. The risk can be managed effectively if

sensible and appropriate rules for use and maintenance are applied!

1. The most important rule when handling the mechanism is to ALWAYS DISCONNECT IT

from its power source when ASSEMBLING THE UNIT, opening the control box or the

drive motor. (the only case when this doesn’t apply is when you manually reset the

Yaskawa).

2. The control box and the wiring used within the game are NOT WATER PROOF OR

WATER RESISTANT, therefore we do not recommend operating the unit in the rain.

Using electrical equipment in wet or damp conditions can be dangerous. If you suspect

water has entered any of the electrical components they should not be used until

completely dry and tested. We recommend taking professional advice where necessary.

3. All cables and electrical equipment must be tested in accordance with the regulations of

your country.

4. In accordance with HSE (UK) guidelines, all 240v equipment should be protected with an

RCD (Residual Current Device) having a maximum trip current of 30 mA. RCD’s are

available from Airquee or your electrical store.

When using it with a generator, make sure it has an output of more than 4 kVA (kilo-volt-ampere),

and a stable 230 Volts on 50Hz.

7. Setup:

7.1 Assembly of the mechanism (AQ4816SP4):

CAUTION! MAKE SURE THE MECHANISM IS NOT

CONNECTED TO A POWER SOURCE WHEN ASSEMBLING IT!

Cycle times of acceleration

/deceleration:

If you are sure thatthis isthe case, and we would need to change

the values, please contact Tilda@airquee.co.uk for further

assistance.

Overvoltage:

The motor will give an error code if the input voltage is too high.

Make sure you change the generator to a smaller one.

Page 6of 14

The mechanism consists of:

- Place the drive motor cover on top of the

drive motor, then insert the wheels and

tighten them with the supplied bolts.

- Unfold the bed at the desired location

and move the drive motor to the center

of the bed.

Sealed Tube

with PVC cover

Drive Motor

Spring Cover

Drive Motor

Cover

Bed Hole

Cover

AP2963

AP2786

AP3149

AP3152

Metal Arm

Middle Bar

Wheels

Legs

Leg Covers

MP0049

MP0022

MP0004

MP0003

AP3151

BED

Page 7of 14

- Exchange the wheels with the legs.

- Insert the middle bar into the drive motor’s

shaft and tighten the bolts at the desired

height. We recommend the second and third

holes at least.

- Insert the metal arm and tighten both

bolts (the upper and the spring bolt).

MAKE SURE BOTH BOLTS ARE ACTUALLY INSIDE A

HOLE BEFORE TIGHTENING THEM. THIS WAY YOU

PREVENT THE BOLTS SCRATCHING THE MIDDLE BAR!

THIS BOLT ADJUSTS

HOW HIGH THE ARM

CAN JUMP

MAKE SURE THE SURFACE WHERE

YOU PLACE THE MECHANISM IS LEVEL!

Page 8of 14

- The spring has a screw thread, which allows it to be tightened manually.

It will be easier if you loosen the spring before you add the metal arm to the middle bar.

7.2 Adding the sealed tube:

DO NOT INFLATE THE SEALED TUBE

BEFORE YOU SLIP IT ON THE ARM BAR!

- Slip the sealed tube on the metal arm, using

the highlighted hole.

- Inflate the sealed tube through the valve with

the help of the supplied hand held fan. When

deflating the sealed tube, you must PRESS

THE MIDDLE OF THE VALVE, this way

opening it. You can close the valve by

pressing its middle again. Don’t forget to fit the

cap on the valve after inflating.

- Bind the webbing around the middle bar

and tie the eyelets with the supplied rope.

- The highlighted PVC loop is for pulling the

uninflated sealed tube in its cover. Make

sure it is hidden when using the LOS. It may

harm users when rotating.

- Cover the spring with the spring cover.

Page 9of 14

- Connect the drive motor to the control

panel with the 12m cable. The electric

socket can be found inside the drive motor.

7.3 Assembly of the bed:

- Start connecting the sandwich Velcro flaps. The easiest way to connect the

flaps is to first patch the lower part of the Velcro all the way, then cover the top

part of the right side soft Velcro with the left side hard Velcro flap.

- You may inflate the bed. While inflating, adjust the position of the bed around the

mechanism with the help of the anchor points, to make sure the mechanism stands in the

middle of its designated hole.

- After inflating, add the bed hole cover.

- Add the podiums/numbers.

THE LOWER PART OF THE SANDWICH VELCRO

Step 1

Step 2

Page 10 of 14

7.4 Assembly of the Control Panel:

The Control Panel consists of:

- You must bolt these 3 parts together to make

it stable.

7.4.1 The Control Box:

1. 12m cable electrical output socket.

2. Main power cable.

3. Main On/Off switch. It works only with the supplied keys.

4. Emergency Stop: In case you must stop the mechanism

suddenly.

5. This will light up when the control panel is under power,

and the key is turned to ON.

6. You can change the movement direction of the arm.

7. Adjusting the speed of the arm.

8. Key hole to open the control box.

7.4.2 Transporting and storing

When packing away the mechanism for transporting/storing, we advise to:

- remove the keys of the control box.

- do not place anything heavy on the control box or on any part of the mechanism.

- make sure the mechanical parts are packed and protected correctly.

- store the mechanism in dry conditions/in a dry place.

Control Box

Support Bar

Legs

ON/OFF

Key

Triangle

Key

12M Cable

3M Cable

AP2785

MP0013

MP0012

MP0056

MP0015

MP0008

MP0009

Otros manuales para Last One Standing

Tabla de contenidos

Otros manuales de Juegos y equipos de juegos infantiles de airquee

airquee

airquee Last One Standing Instrucciones de funcionamiento

airquee

airquee PILLOW PIT Manual de usuario

airquee

airquee Dash n' Grab Instrucciones de funcionamiento

airquee

airquee Sumo Suits Instrucciones de funcionamiento

airquee

airquee DISCO READY FEATURE Instrucciones de funcionamiento

airquee

airquee WORLD'S BIGGEST BOUNCY CASTLE Manual de usuario

airquee

airquee Disco Dome Instrucciones de funcionamiento

airquee

airquee Arena Extreme Instrucciones de funcionamiento

airquee

airquee Zorb Ball Instrucciones de funcionamiento

airquee

airquee RUSH SLIDE AQ5765 Instrucciones de funcionamiento

airquee

airquee Mountain Climb Instrucciones de funcionamiento

airquee

airquee Bouncing Balls Instrucciones de funcionamiento

airquee

airquee Spinning Disc Challenge Manual de usuario

airquee

airquee Sealed Building Instrucciones de funcionamiento

airquee

airquee 2 Part Energy Assault Course Instrucciones de funcionamiento

airquee

airquee Trampoline Bouncer Instrucciones de funcionamiento

airquee

airquee Inflatable Bull Manual de usuario

airquee

airquee The Hogshead Instrucciones de funcionamiento

airquee

airquee 8M Platform Slide Instrucciones de funcionamiento

airquee

airquee PLAYMAZE Instrucciones de funcionamiento

airquee

airquee PLAYZONE AQ2711 Manual de usuario

airquee

airquee Catch it Quick Game Instrucciones de funcionamiento

airquee

airquee Kick N Stick Dual Upright Instrucciones de funcionamiento

airquee

airquee Air Buildings Instrucciones de funcionamiento

Manuales populares de Juegos y equipos de juegos infantiles de otras marcas

Ledon

Ledon 302040 Manual de usuario

FUNormous

FUNormous Disney Junior MICKEY MOUSE Manual de usuario

b4Adventure

b4Adventure Slackers TREEZONE ADVENTURE THREE HOUSE Manual de usuario

PoolMaster

PoolMaster 72775 Manual de usuario

Palmako

Palmako 4743142009857 Manual del instalador

BOERPLAY

BOERPLAY PSTE000.019 Manual de usuario

MGA Entertainment

MGA Entertainment Little Tikes Dunk'n Toss Bouncer Guía del usuario

stilum

stilum Erika Manual de usuario

Costway

Costway NP10816 Manual de usuario

Trigano

Trigano VABI Manual de usuario

Outward

Outward OUT116 Manual de usuario

GALOPIN

GALOPIN ARC02 Manual de usuario

stilum

stilum levis Especificaciones técnicas

Ledon

Ledon BASIC Bai LB012 Manual de usuario

BOERPLAY

BOERPLAY PSTE115.002 Manual de usuario

Europlay

Europlay S306 Manual de programación

SportsPlay Equipment

SportsPlay Equipment 361-509H Manual de usuario

Ledon

Ledon 302250 Manual de usuario