Airmax SilentAir LR50 Manual de usuario
INSTALLATION INSTRUCTIONS
C
E
ABD
A2 Outer Diaphragms
B2 Inner Diaphragms
C2 Diaphragm Front Boards
D2 Diaphragm Backs Boards
E4 Protective Washers
What’s Included:
B
E E
D
Diaphragm Assembly
C
SilentAir™ LR50
Diaphragm Compressor
Maintenance Kit:
Installation of your
LR50 Compressor Maintenance Kit
• Phillips Screwdriver
• Flat Head Screwdriver
• 7mm Nut Driver
• Small Pick Tool
Tools Required:
Step 1
Flip the compressor upside down.
Use a Phillips screwdriver to remove
the four screws holding down the
compressor cover. Save the screws
and lock washers.
Step 2
Use a at head screwdriver to loosen
the seal of the gasket on the top
compressor cover. Gently pull up
on the bottom of the compressor
to separate. Flip the whole unit over
and remove the compressor cover
and set to the side.
Watch the installation video at
airmaxeco.com/InstallLR50
Warning: Always unplug the
unit before any maintenance.
airmaxeco.com | 866-424-7629
2
Step 4
Remove the cover and set to the
side. Inspect for any dust or wear
on the inside of the unit.
Step 5
Pinch the spring clamp to remove
the rubber boot attached to the
outer diaphragm.
Step 3
Use a Phillips screwdriver to remove
the four screws on the top cover
plate. Make sure to save the lock
washers on the screws.
Step 6
Use a Phillips screwdriver to remove
the four screws holding the outer
diaphragm into place. Make sure to
keep both the at washer and lock
washer with each of the four screws.
P.O.Box 38 | Romeo, MI 48065 3
Step 9
Remove and discard the diaphragm
front board.
Step 7
Remove the outer diaphragm
and discard.
Step 8
Use a 7mm nut driver to remove
the nut on the inner diaphragm.
Make sure to keep the nut and lock
washer. Remove and discard the
diaphragm backboard followed by
the inner diaphragm.
airmaxeco.com | 866-424-7629
4
Step 12
Push the front board rmly into
place and make sure the pegs come
through evenly on the reverse side
of the inner diaphragm.
Step 13
Install the inner diaphragm into the
armature with the two lines on the
front board being vertical.
Step 10
Apply the protective washer on top
of the diaphragm front board. The
diaphragm front board is the one
with four pegs.
Step 11
Align the four pegs up with the four
holes inside the inner diaphragm.
Align the two lines on the front
board to be pointing to the notches
on the inner diaphragm.
Notch
Notch
P.O.Box 38 | Romeo, MI 48065 5
Step 15
Install the lock washer and nut.
Use the 7mm nut driver to securely
tighten the nut.
Step 16
Reinstall the outer diaphragm.
Align the diaphragm intake to point
towards the rubber boot.
Step 17
Reuse the four screws that you
removed from earlier to secure the
outer diaphragm into place. Pre-start
the top two screws rst with a Phillips
screwdriver. This will help make it
easier when installing the bottom
two screws. Securely tighten all four
screws evenly to ensure a proper seal.
Step 14
Install the 2nd protective washer
onto the diaphragm followed by
the diaphragm backboard. The
backboard should be installed with
the curved side facing inward. It can
be helpful to tilt the compressor to
keep the washer and diaphragm
backboard in place. Make sure the
protective washer is installed evenly
between the diaphragm backboard
and the diaphragm.
airmaxeco.com | 866-424-7629
6
Step 20
Reinstall the diaphragm top
plate. Reinstall the four screws
with washers to the top plate and
securely tighten.
Step 21
Reinstall the compressor cover. Flip
the entire compressor upside down
and secure using the four screws
with washers. Tighten down rmly
to complete the installation.
Once complete, we recommend
to change the compressor air lter.
See instructions on pg. 8.
Step 18
Reinstall the rubber hose and
spring clamp. Now that this side is
complete, repeat steps 5 thru 17 for
the 2nd diaphragm before moving
on to Step 19.
Step 19
After completing both diaphragms,
double check to make sure you
have proper alignment between
the two stators.
P.O.Box 38 | Romeo, MI 48065 7
Changing the Air Filter:
Step 1Unscrew and remove the
lock nut and remove the top cover.
Step 2 Remove the old air lter
and install a new one.
Step 3 Reinstall the top cover.
Make sure the notch in the top
cover lines up with the notch on
top of the compressor.
Step 4 Reinstall the lock nut.
THANK YOU FOR CHOOSING:
Airmax®, Inc.
Safe, Simple Solutions™
P.O. Box 38
Romeo, MI 48065
866-424-7629
www.airmaxeco.com
8
Tabla de contenidos
Otros manuales de Compresor de aire de Airmax
Airmax
Airmax LR25 Guía de mantenimiento y servicio
Airmax
Airmax SilentAir G33 Manual de usuario
Airmax
Airmax ProAir 4 Manual de usuario
Airmax
Airmax AMC062-1 Manual de usuario
Airmax
Airmax SilentAir RP25 (87R) Manual de usuario
Airmax
Airmax Crystal Clear PondAir 2 Manual de usuario
Airmax
Airmax Pond Logic SilentAir SW Series Guía de mantenimiento y servicio
Airmax
Airmax T100 Manual de usuario
Airmax
Airmax SW20 Manual de usuario
Airmax
Airmax SilentAir G75 Manual de usuario
