Airlink101 AGIGAUSB Manual de usuario
USB 2.0 Gigabit Network Adapter
Model # AGIGAUSB
User’s Manual
Ver. 1A
2
Table of Contents
Introduction .....................................................................................................................4
Package Contents .......................................................................................................4
Specifications ..............................................................................................................4
Network Specification...............................................................................................4
Host Interface...........................................................................................................4
Supported operating systems ..................................................................................4
LED Indicators..........................................................................................................4
Power Requirement .................................................................................................5
EMC Certification.....................................................................................................5
Installation.......................................................................................................................6
Verify Driver Installation ................................................................................................12
Technical Support .........................................................................................................14
3
REGULATORY STATEMENTS
FCC Certification
Part15, Class B
The United States Federal Communication Commission (FCC) and the Canadian Department of
Communications have established certain rules governing the use of electronic equipment.
FCC Part 15 Registration
This device complies with Part 15 of FCC rules. Operation is subject to the following two
conditions:
•This device may not cause harmful interface, and
•This device must accept any interface received, including interface that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the distance between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
4
Introduction
The USB 2.0 Gigabit Network Adapter (hereafter referred to as the Gigabit Adapter) is
specifically designed to plug into any available Universal Serial Bus port of a desktop or
laptop PC. The Gigabit Adapter is for users who wish to connect to a 10Mbps, 100Mbps
or 1000Mbps Fast Ethernet LAN using the convenience and ease of USB technology.
The Gigabit Adapter complies with USB Specification 1.0/1.1/2.0. It uses an USB type B
connector to connect directly to the USB host computer and a RJ-45 connector provides
a quick and simple method of connecting to an Ethernet or Fast Ethernet network.
This low power-consuming device draws power from the host USB bus directly, so no
external power supply is required. Simply connect the USB port of this device to the
computer and plug a standard twisted-pair Ethernet cable into the RJ-45 port, and you’ll
be networked in no time. This device offers a simple way to connect to your network.
Package Contents
•Gigabit Network Adapter
•USB 2.0 Cable
•Driver CD
•Quick Installation Guide
Specifications
Network Specification
•IEEE802.3 10BaseT, 802.3u 100BaseTX and 802.3ab 1000Base-T.
•Cat3/Cat5 UTP cable up to 328ft/100M.
Host Interface
•High-power Bus-powered from USB HOST or HUB, no external power needed.
•Full Speed/High Speed USB device, upstream B USB port.
Supported operating systems
•Windows 2000/XP
LED Indicators
•Link: When the device is well-connected to the computer, the Link LED will
appear as solid green.
•TX/RX: 10/100/Gigabit linking status
10Mbps: Appears as solid orange + green when the device is connected to 10Mbps
network; blinking orange + green when transmitting data.
5
100Mbps: Appears as solid orange when the device is connected to 100Mbps network;
blinking orange when transmitting data.
Gigabit: Appears as solid green, when the device is connected to Gigabit network;
blinking green when transmitting data.
Power Requirement
Operating Voltage: 5V DC
Operation Mode: 425mA (Max)
Physical specification
Dimension: 3.2"(L) x 2.2"(W) x1" (H)
EMC Certification
•FCC Part15 ClassB
•CE
•VCCI
6
Installation
The following steps and screen shots are for Windows XP. Steps for Windows 2000 are
similar unless noted otherwise.
Note: Do not connect the USB 2.0 Gigabit Network Adapter to your computer until
you’ve reached the appointed step. If the Gigabit Adapter is connected already,
Windows will detect the Adapter and request for a driver. Click Cancel to quit the wizard
and remove the Gigabit Adapter from your computer.
Step 1 Insert the Driver CD into your CD drive and wait for the autorun window to
appear on screen.
Step 2 Click on Install Driver at the autorun window.
Note: If the autorun window doesn’t appear automatically go to Start, Run, and type
D:\autorun.exe (where D is the letter of your CD drive) and click OK.
7
Step 3 Click Next at the welcome screen.
Step 4 Click Next to accept the default destination location for the driver to be installed
in or click Browse to select the desired location.
8
Step 5 Click Next to accept the Program Folder for the driver.
Step 6 Click Continue Anyway at the Windows Logo Testing prompt.
(For Windows 2000, click Yes at the Digital Signature Not Found prompt).
9
Step 7 Click Finish to complete the installation wizard.
Step 8 Connect one end of the Gigabit Network Adapter to your computer’s USB port
and connect the other end to a hub/switch/router.
Step 9 At the Found New Hardware Wizard window, select No, not this time and
click Next.
10
Step 10 Select Install the software automatically (Recommended) and click Next.
For Windows 2000, select Search for a suitable driver for my device
(Recommended) and click Next. Then check on the CD-ROM drives check box and
click Next.
Step 11 Click Continue Anyway at the Windows Logo Testing prompt.
(For Windows 2000, click Yes at the Digital Signature Not Found prompt).
Tabla de contenidos
Otros manuales de Adaptador de Airlink101
Airlink101
Airlink101 ATVUSB01 Manual de usuario
Airlink101
Airlink101 AWLC6070 Manual de usuario
Airlink101
Airlink101 AWLL6070 Manual de usuario
Airlink101
Airlink101 AWLL3025v2 Manual de usuario
Airlink101
Airlink101 APL8512 Manual de usuario
Airlink101
Airlink101 AWLC6045 Manual de usuario
Airlink101
Airlink101 AWLL5099 Manual de usuario
Airlink101
Airlink101 AWLL3026 Manual de usuario
Airlink101
Airlink101 AWLL6070 Manual de usuario
Airlink101
Airlink101 AWLC3026 Manual de usuario
Airlink101
Airlink101 AWLL5166HP Manual de usuario
Airlink101
Airlink101 AWLL3028 Manual de usuario
Airlink101
Airlink101 AWLC3026 Manual de usuario
Airlink101
Airlink101 ATVUSB01 Manual de usuario
Airlink101
Airlink101 ASOHOUSB Manual de usuario
Airlink101
Airlink101 AWLL4030 Manual de usuario
Airlink101
Airlink101 AWLL5166HP Manual de usuario
Airlink101
Airlink101 AWLL7025 Manual de usuario
Airlink101
Airlink101 AWLC6045 Manual de usuario
Airlink101
Airlink101 ASOHORL Manual de usuario
