Aircatglobal Virtualfly V3RNIO Manual de usuario
© 2021 Virtual Fly, SL
All trademarks and brand names are
trademarks or registered trademarks of their
respective owners. All rights reserved.
V3RNIO & V3RNIO+
USER’S MANUAL
Rev 2.0 - September 2021
1. IN THE BOX
A) V3RNIO / V3RNIO+
B) Clamp
C) Allen Screws
D) Allen Key
E) USB-B to USB Cable
C. Maria Aurèlia Capmany, 21
P.I. La Fàbrica – 08297 Castellgalí (Spain)
Phone: (+34) 983 333 301
www.virtual-fly.com
For support visit help.virtual-fly.com
or contact us at support@virtual-fly.com
V3RNIO / V3RNIO+ | User’s manual
2
2. HARDWARE SETUP
2.1 Using the V3RNIO/V3RNIO+ on a desk
Use the four screws (C) to attach the clamp (B) to the
V3RNIO/V3RNIO+ as seen in the picture. Now you can
secure the device to the desk.
Finally, connect the USB-B to USB cable (E) between
the V3RNIO/V3RNIO+ and the computer where the flight
simulation software is running.
2.2. Using the V3RNIO/V3RNIO+ in a
flight panel
To attach the V3RNIO/V3RNIO+ to your custom flight panel,
unscrew the six front screws to remove the cover. Now, you
can mount the V3RNIO into a fitting socket. Find the exact
measures in PDF and DXF format at https://www.virtual-fly.
com/downloads
Finally, connect the USB-B to USB cable (E) between
the V3RNIO/V3RNIO+ and the computer where the flight
simulation software is running.
V3RNIO / V3RNIO+ | User’s manual 3
2.3. Chaning the V3RNIO levers’ hardness
V3RNIO levers move forward and backward precisely.
Tightening the screw under each lever adjusts its hardness.
2.4. Chaning the V3RNIO+ levers’ hardness
The THROTTLE lever from the V3RNIO+ moves forward and
backward, and you can adjust the hardness by rotating the
adjustment wheel, as seen in the picture.
The PROP and MIXTURE levers can be adjusted precisely,
rotating each handle, as seen in the picture. If you want to
move them quickly forward or backward, you can do so
while pressing the front button.
V3RNIO / V3RNIO+ | User’s manual
4
3. SOFTWARE SETUP
The V3RNIO/V3RNIO+ interacts with any computer as a
joystick (HID), so it is compatible with any flight simulation
software. Below, you have two options for setting up your
V3RNIO/V3RNIO+ with the most popular flight simulation
software: MSFS, Prepar3D, and X-Plane.
3.1. Using VFHUB
VFHub is the software built by Virtual Fly to reduce the
complicated to the simple. It is the recommended software
setup for your V3RNIO/V3RNIO+. With VFHub, you can fly
your favorite flight simulation software without worrying
about configuring your Virtual Fly flight controls.
You can download the VFHub installer from https://www.
virtual-fly.com/downloads. The VFHub installer takes care of
installing VFHub together with all the required modules.
Connect the V3RNIO/V3RNIO+ to your computer, open
VFHub, and start flying right away. VFHub takes care of
making your V3RNIO/V3RNIO+ work with MSFS, Prepar3D,
and X-Plane.
If you use MSFS or X-Plane, set a blank profile to
the V3RNIO/V3RNIO+ in the controls or joysticks
setup menu before using your device. You can find
the detailed steps on how to set a blank profile
here: https://downloads.virtual-fly.com/docs/vub/
latest/VFHUB_SET_BLANK_PROFILES.pdf
If you want to customize how your V3RNIO/
V3RNIO+ works, make sure you read the VFHub
user’s manual available at https://downloads.
virtual-fly.com/docs/vub/latest/VFHUB_USER’S_
MANUAL.pdf for detailed instructions on all the
tuning and customization possibilities.
V3RNIO / V3RNIO+ | User’s manual 5
3.2 Using an alternative joystick
configuration
Since the V3RNIO/V3RNIO+ interacts with any computer
as a joystick (HID), it is compatible with any flight simulation
software. Below, you have a general scheme for setting
up your V3RNIO/V3RNIO+ with the most popular flight
simulation software: MSFS, Prepar3D, and X-Plane.
MSFS
Assign the axes inside the controls menu, and the V3RNIO/
V3RNIO+ will be ready to be used.
Finally, restart MSFS and verify that the device is configured
correctly.
Prepar3D
Open Prepar3D and go to the controls menu. Inside, select
the ‘V3RNIO/V3RNIO+’ from the devices list. Assign the
axes as you please. Then calibrate the device following the
instructions.
Finally, restart Prepar3D and verify that the device is
configured correctly.
X-Plane
Your V3RNIO/V3RNIO+ needs to be calibrated inside X-Plane
since axes are automatically assigned. Open X-Plane, go to
Configuration\Joystick, and follow the calibration steps for
your device.
Finally, restart X-Plane and verify that the device is configured
correctly.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Pantalla aviónica de Aircatglobal
Aircatglobal
Aircatglobal VirtualFly VF-G1000 Manual de usuario
Aircatglobal
Aircatglobal VirtualFly SOLO GA Manual de usuario
Aircatglobal
Aircatglobal VirtualFly SOLO AIRLINER Manual de usuario
Aircatglobal
Aircatglobal VirtualFly SOLO AIRLINER-RS Manual de usuario
Aircatglobal
Aircatglobal Virtualfly COMPOSS Manual de usuario
Manuales populares de Pantalla aviónica de otras marcas
Smart Avionics
Smart Avionics PB-4 Manual de usuario
Midcontinent
Midcontinent SAM MD302 Manual
MGL Avionics
MGL Avionics Stratomaster Maxi Single FF-3 Manual de usuario
Garmin
Garmin GI 275 Manual de usuario
Mid-Continent Instruments
Mid-Continent Instruments 4300 Series Manual
Avidyne
Avidyne 700-00182 Series Manual de servicio
