AIC RSC-15 Manual de usuario

RSC-15
Rackmount Storage Chassis
User's Manual
UM_RSC-15_v.2_061616

contents
CONTENTS
PREFACE������������������������������������������������������������������������������������������� i
SAFETY INSTRUCTIONS�������������������������������������������������������������������� ii
Chapter 1� Prodcut Introduction ������������������������������������������������ 1
1�1 Box Content ����������������������������������������������������������������������������������������1
1.2 Specications �������������������������������������������������������������������������������������2
1�3 General Information���������������������������������������������������������������������������3
Chapter 2� Hardware Installation����������������������������������������������� 6
2�1 Removing and Installing Top Cover �������������������������������������������������6
2�2 Installing/ Removing a Hard Disk Drive��������������������������������������������7
2�3 Removing and Installing a PSU Module �������������������������������������������8
2�6 Removing and Installing a Fan Module �������������������������������������������9
2�4 Removing and Installing a Fan Module �������������������������������������������9
2�5 Removing and Installing the HDD backplane Module����������������11
2�6 Removing and Installing a 2�5-inch SSD ����������������������������������������12
2�8 Tool-less Blade Slide Installation Introduction �������������������������������13
Chapter 3� Hardware Instruction���������������������������������������������� 17
3�1 HARDWARE DESIGN SPECIFICATION �����������������������������������������������17
3�2 Drive Slot Map�����������������������������������������������������������������������������������19
Chapter 4� Technical Support��������������������������������������������������� 20

Copyright © 2016 AIC, Inc� All Rights Reserved�
This document contains proprietary information about
AIC products and is not to be disclosed or used except in
accordance with applicable agreements.

i
PREFACE
• Copyright
No part of this publication may be reproduced, stored in a retrieval system,
or transmitted in any form or by any means, electronic, mechanical, photo-
static, recording or otherwise, without the prior written consent of the
manufacturer.
• Trademarks
All products and trade names used in this document are trademarks or
registered trademarks of their respective holders.
• Changes
The material in this document is for information purposes only and is subject
to change without notice.
• Warning
1. A shielded-type power cord is required in order to meet FCC emission
limits and also to prevent interference to the nearby radio and television
reception. It is essential that only the supplied power cord be used.
2. Use only shielded cables to connect I/O devices to this equipment.
3. You are cautioned that changes or modications not expressly approved
by the party responsible for compliance could void your authority to
operate the equipment.
• Disclaimer
AIC shall not be liable for technical or editorial errors or omissions
contained herein. The information provided is provided "as is" without
warranty of any kind. To the extent permitted by law, neither AIC or its
affiliates, subcontractors or suppliers will be liable for incidental, special or
consequential damages including downtime cost; lost profits; damages
relating to the procurement of substitute products or services; or damages
for loss of data, or software restoration. The information in this document is
subject to change without notice.

ii
SAFETY INSTRUCTIONS
• Before getting started, please read the following important cautions:
• All cautions and warnings on the equipment or in the manuals should be
noted.
• Most electronic components are sensitive to electrical static discharge.
Therefore, be sure to ground yourself at all times when installing the
internal components.
• Use a grounding wrist strap and place all electronic components in
static-shielded devices. Grounding wrist straps can be purchased in any
electronic supply store.
• Be sure to turn off the power and then disconnect the power cords from
your system before performing any installation or servicing. A sudden
surge of power could damage sensitive electronic components.
• Do not open the system’s top cover. If opening the cover for
maintenance is a must, only a trained technician should do so.
Integrated circuits on computer boards are sensitive to static electricity.
Before handling a board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. This will help to
discharge any static electricity on your body.
• Place this equipment on a stable surface when install. A drop or fall
could cause injury.
• Please keep this equipment away from humidity.
• Carefully mount the equipment into the rack, in such manner, that it
won’t be hazardous due to uneven mechanical loading.
• This equipment is to be installed for operation in an environment with
maximum ambient temperature below 35°C.
• The openings on the enclosure are for air convection to protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
• Never pour any liquid into ventilation openings. This could cause re or
electrical shock.
• Make sure the voltage of the power source is within the specification
on the label when connecting the equipment to the power outlet. The
current load and output power of loads shall be within the specication.
• This equipment must be connected to reliable grounding before using.
Pay special attention to power supplied other than direct connections,
e.g. using of power strips.
• Place the power cord out of the way of foot traffic. Do not place
anything over the power cord. The power cord must be rated for the

iii
• product, voltage and current marked on the product’s electrical ratings
label. The voltage and current rating of the cord should be greater than the
voltage and current rating marked on the product.
• If the equipment is not used for a long time, disconnect the equipment from
mains to avoid being damaged by transient over-voltage.
• Never open the equipment. For safety reasons, only qualified service
personnel should open the equipment.
• If one of the following situations arise, the equipment should be checked by
service personnel:
1. The power cord or plug is damaged.
2. Liquid has penetrated the equipment.
3. The equipment has been exposed to moisture.
4. The equipment does not work well or will not work according to its user
manual.
5. The equipment has been dropped and/or damaged.
6. The equipment has obvious signs of breakage.
7. Please disconnect this equipment from the AC outlet before cleaning.
Do not use liquid or detergent for cleaning. The use of a moisture sheet or
cloth is recommended for cleaning.
• Module and drive bays must not be empty! They must have a dummy cover.
Product features and specications are subject to change without notice.
CAUTION :
risk of explosion if battery is replaced by an incorrect type.
dispose of used batteries according to the instructions.
After performing any installation or servicing, make sure the
enclosure are lock and screw in position, turn on the power.

1
RSC-15 User's Manual
Chapter 1 Product Introduction
1�1 Box Content
Before removing the subsystem from the shipping carton, visually inspect the
physical condition of the shipping carton. Exterior damage to the shipping
carton may indicate that the contents of the carton are damaged. If any
damage is found, do not remove the components; contact the dealer where
the subsystem was purchased for further instructions. Before continuing, rst
unpack the subsystem and verify that the contents of the shipping carton are
all there and in good condition.
• Enclosure( Power supply, fan, 16 x 3.5'' HDD tray included)
• Power cord • Screws kit x 1pcs
• (Include console
serial cable)
• Slide rail x 1set ♦PACKAGE CONTENT MAY VARY PER REGION.
Chapter 1� Prodcut Introduction

2
RSC-15 User's Manual
Chapter 1 Product Introduction
1.2 Specications
Dimensions
(W x D x H)
(with chassis ears)
Standard mm : 483 x 910 x 66.6
inches : 19 x 35.8 x 2.6
Option mm : 483 x 838.2 x 66.6
inches : 19 x 33 x 2.6
Industry Standard EIA-RS310D
Material Heavy-duty preplated SPGC cold-rolled steel
Color Not coated
Cooling Middle : 4 x 60x38mm PWM easy swap fans
Power Supply 650W 1+1 redundant PSU 80+ Gold
Expansion Slots 1 full height & 1 low prole via riser card
(6th + 5th slots or 6th + 4th slots)
Front Panel System power on/off and system reset
LED Indicators Power, LAN and Drive
System Board
12”(W) x 13”(D) E-ATX/SSI EEB 3.6 compliant MB
12”(W) x 9.6”(D) ATX (for 33” depth option)
Drive Bays Internal
3.5” hot swap 16
2.5” 2
Backplanes 4 x 4-port 6Gb SAS backplanes with single
SFF-8087 connector on each
Storage Temperature 0ºC(32ºF) ~ 50ºC(122ºF)
Humidity 5%~95% non-condensing
Gross Weight (w/ PSU & Rail)
kgs : 28
lbs : 61.7
Packaging
Dimensions (W x D x H)
mm : 590 x 1070 x 280
inches : 23.2 x 42.1 x 11
Cubic Feet 6.2
Container Load
Quantity
20’ 155
40’ 150
40’ H 385
Mounting Standard 30” tool-less slide rail

3
RSC-15 User's Manual
Chapter 1 Product Introduction
System power on/off and system reset
2 drawers, each loads 8 x 3.5” drives
1�3 General Information
RSC-15 is a 1.5U rackmount chassis with 16 x 3.5”HDD hot swap Bays at Top
and single 12G expander on HDD Backplane which is a high performance
server storage product.
• Front Panel
System Reset button LAN1 Power LED
LAN2 Power LED System HDD Activity LED
Power System LED Power On/Off Button

4
RSC-15 User's Manual
Chapter 1 Product Introduction
• Rear Panel
2 x8 PCIe 3.0 slots
750W 1+1 redundant PSU 80+ Gold
Tabla de contenidos
Otros manuales de Almacenamiento de AIC
Manuales populares de Almacenamiento de otras marcas

Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic
Panasonic LKM-F931-1 Manual de usuario

Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor
Rocstor COMMANDER 3F series Manual de usuario

HP
HP P9000 Manual de usuario

Western Digital
Western Digital Ultrastar Data60 Manual de usuario



















