AIC RSC-4BT Manual de usuario

RSC-4BT
Rackmount Storage Chassis
User's Manual
UM_RSC-4BT_v1.1_100617

contents
CONTENTS
PREFACE������������������������������������������������������������������������������������������� i
SAFETY INSTRUCTIONS�������������������������������������������������������������������� ii
Chapter 1� Prodcut Introduction ������������������������������������������������ 1
1�1 Box Content ����������������������������������������������������������������������������������������1
1.2 Specications �������������������������������������������������������������������������������������2
1�3 General Information���������������������������������������������������������������������������3
Chapter 2� Hardware Installation����������������������������������������������� 6
2�1 Removing and Installing Top Cover �������������������������������������������������6
2�2 Installing/ Removing a Hard Disk Drive��������������������������������������������7
2�3 Removing and Installing a PSU Module �������������������������������������������9
2�4 Removing and Installing a Fan Module �����������������������������������������10
2�5 Removing and Installing the HDD backplane Module����������������12
2�6 Tool-less Blade Slide Installation Instruction ����������������������������������14
Chapter 3� Hardware Introduction������������������������������������������� 21
3�1 HARDWARE DESIGN SPECIFICATION �����������������������������������������������21
Chapter 4� HDD Blackplane Introduction�������������������������������� 28
4.1 Expender rmware update through phone connector port ��������28
4.2 Update the expander rmware through in-band. ������������������������41
4�3 12G expander EDFB setting �������������������������������������������������������������45
4�4 Slot HDD power setting���������������������������������������������������������������������47
4�5 HDD BP thermal sensor temperature setting����������������������������������52
Chapter 5� Technical Support��������������������������������������������������� 55

Copyright © 2017 AIC, Inc� All Rights Reserved�
This document contains proprietary information about
AIC products and is not to be disclosed or used except in
accordance with applicable agreements.

i
PREFACE
• Copyright
No part of this publication may be reproduced, stored in a retrieval system,
or transmitted in any form or by any means, electronic, mechanical, photo-
static, recording or otherwise, without the prior written consent of the
manufacturer.
• Trademarks
All products and trade names used in this document are trademarks or
registered trademarks of their respective holders.
• Changes
The material in this document is for information purposes only and is subject
to change without notice.
• Warning
1. A shielded-type power cord is required in order to meet FCC emission
limits and also to prevent interference to the nearby radio and television
reception. It is essential that only the supplied power cord be used.
2. Use only shielded cables to connect I/O devices to this equipment.
3. You are cautioned that changes or modications not expressly approved
by the party responsible for compliance could void your authority to
operate the equipment.
• Disclaimer
AIC shall not be liable for technical or editorial errors or omissions
contained herein. The information provided is provided "as is" without
warranty of any kind. To the extent permitted by law, neither AIC or its
affiliates, subcontractors or suppliers will be liable for incidental, special or
consequential damages including downtime cost; lost profits; damages
relating to the procurement of substitute products or services; or damages
for loss of data, or software restoration. The information in this document is
subject to change without notice.

ii
SAFETY INSTRUCTIONS
• Before getting started, please read the following important cautions:
• All cautions and warnings on the equipment or in the manuals should be
noted.
• Most electronic components are sensitive to electrical static discharge.
Therefore, be sure to ground yourself at all times when installing the
internal components.
• Use a grounding wrist strap and place all electronic components in
static-shielded devices. Grounding wrist straps can be purchased in any
electronic supply store.
• Be sure to turn off the power and then disconnect the power cords from
your system before performing any installation or servicing. A sudden
surge of power could damage sensitive electronic components.
• Do not open the system’s top cover. If opening the cover for
maintenance is a must, only a trained technician should do so.
Integrated circuits on computer boards are sensitive to static electricity.
Before handling a board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. This will help to
discharge any static electricity on your body.
• Place this equipment on a stable surface when install. A drop or fall
could cause injury.
• Please keep this equipment away from humidity.
• Carefully mount the equipment into the rack, in such manner, that it
won’t be hazardous due to uneven mechanical loading.
• This equipment is to be installed for operation in an environment with
maximum ambient temperature below 35°C.
• The openings on the enclosure are for air convection to protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
• Never pour any liquid into ventilation openings. This could cause re or
electrical shock.
• Make sure the voltage of the power source is within the specification
on the label when connecting the equipment to the power outlet. The
current load and output power of loads shall be within the specication.
• This equipment must be connected to reliable grounding before using.
Pay special attention to power supplied other than direct connections,
e.g. using of power strips.
• Place the power cord out of the way of foot traffic. Do not place
anything over the power cord. The power cord must be rated for the

iii
• product, voltage and current marked on the product’s electrical ratings
label. The voltage and current rating of the cord should be greater than the
voltage and current rating marked on the product.
• If the equipment is not used for a long time, disconnect the equipment from
mains to avoid being damaged by transient over-voltage.
• Never open the equipment. For safety reasons, only qualified service
personnel should open the equipment.
• If one of the following situations arise, the equipment should be checked by
service personnel:
1. The power cord or plug is damaged.
2. Liquid has penetrated the equipment.
3. The equipment has been exposed to moisture.
4. The equipment does not work well or will not work according to its user
manual.
5. The equipment has been dropped and/or damaged.
6. The equipment has obvious signs of breakage.
7. Please disconnect this equipment from the AC outlet before cleaning.
Do not use liquid or detergent for cleaning. The use of a moisture sheet or
cloth is recommended for cleaning.
• Module and drive bays must not be empty! They must have a dummy cover.
Product features and specications are subject to change without notice.
CAUTION :
risk of explosion if battery is replaced by an incorrect type.
dispose of used batteries according to the instructions.
After performing any installation or servicing, make sure the
enclosure are lock and screw in position, turn on the power.

1
RSC-4BT User's Manual
Chapter 1 Product Introduction
1�1 Box Content
Before removing the subsystem from the shipping carton, visually inspect the
physical condition of the shipping carton. Exterior damage to the shipping
carton may indicate that the contents of the carton are damaged. If any
damage is found, do not remove the components; contact the dealer where
the subsystem was purchased for further instructions. Before continuing, rst
unpack the subsystem and verify that the contents of the shipping carton are
all there and in good condition.
• Enclosure( Power supply, fan, 36 x 3.5'' HDD tray included)
• Power cord • Screws kit x 1set
• (Include console
serial cable)
• Slide rail x 1set
♦PACKAGE CONTENT MAY VARY PER REGION.
Chapter 1� Prodcut Introduction
• 3.5’’ HDD Tray

2
RSC-4BT User's Manual
Chapter 1 Product Introduction
1.2 Specications
Dimensions
(W x D x H)
(with chassis ears)
mm : 483 x 679 x 173.5
inches : 19 x 26.7 x 6.8
Industry Standard EIA-RS310D
Material Heavy-duty preplated SPGC cold-rolled steel
Color Front Panel : Black
Cooling Middle : 6 x 80x38mm PWM & low-power consumption
hot swap fans
Power Supply 1200W 1+1 redundant PSU PMBus 1.2 80+ Platinum
Expansion Slots 7 low prole
Front Panel System power on/off, system reset and 2 x USB 3.0 ports
LED Indicators Power, LAN, Drive and Alert
System Board 12”(W) x 13”(D) E-ATX/SSI EEB 3.6 compliant MB
Drive Bays
External 3.5” hot swap 36 (24 front + 12 rear)
Internal 2.5” 2
Backplanes
1 x 24-port 12Gb SAS backplane with 36-PHY expander
chip and 3 SFF-8643 connectors
1 x 12-port 12Gb SAS backplane with 28-PHY expander
chip and 3 SFF-8643 connectors
Storage
Temperature 0ºC(32ºF) ~ 50ºC(122ºF)
Humidity 5%~95% non-condensing
Gross Weight (w/ PSU & Rail)
kgs : 40.4
lbs : 89
Packaging
Dimensions (W x D x H)
mm : 616 x 921 x 393
inches : 24.3 x 36.3 x 15.5
Cubic Feet 7.6
Container Load
Quantity
20’ 110
40’ 230
40’ H 295
Mounting Standard 26” tool-less slide rail

3
RSC-4BT User's Manual
Chapter 1 Product Introduction
1�3 General Information
RSC-4BT is a 4U rackmount chassis with 36x3.5”HDD hot swap Bays at front
and single 12G expander on HDD Backplane which is a high performance
server storage product.
• Front Panel
2 x USB3.0 ports
24 x 3.5” hotswap HDD trays
Power On / Off Button
System Reset button
System Power LED
System HDD Activity LED
LAN Power LED
System Alert LED
Push for ID LED On or Off

4
RSC-4BT User's Manual
Chapter 1 Product Introduction
• Rear Panel
Option 1:
uHot-swap redundant power supplies
v12 x 3.5'' hot-swap HDD supported
w7 x PCI slots attribute to expansion and scalability
Option 2:
External (Rear) : 2 x 2.5" (7mm) hot swap
Otros manuales para RSC-4BT
1
Tabla de contenidos
Otros manuales de Chasis de AIC

AIC
AIC J4076-01 Manual de usuario

AIC
AIC RSC-2ETS Manual de usuario

AIC
AIC J2012-01 Manual de usuario

AIC
AIC RSC-2KT Manual de usuario

AIC
AIC RSC-4ET Manual de usuario

AIC
AIC RSC-2ET Manual de usuario

AIC
AIC RSC-1R Manual de usuario

AIC
AIC RSC-4BT Manual de usuario

AIC
AIC RSC-1C Manual de usuario

AIC
AIC RSC-2AT Manual de usuario






















