Agri-Fab 45-0355-131 Manual de usuario

PRINTED IN USA FORM NO. 49358 (4/04)

OWNERS

MANUAL

Model No.

3 PT. HITCH

TANG CULTIVATOR

the fastest way to purchase arts

www.speedepart.com

• Safety

• Assembly

• O eration

• Maintenance

• Parts

CAUTION:

Read Rules for

Safe O eration

and Instructions

Carefully

Agri-Fab¨

45-0355-131

For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

SAFETY RULES

Remember, any ower equi ment can cause injury if o erated im ro erly or if the user does not understand how to

o erate the equi ment. Exercise caution at all times when using ower equi ment.

1. Read this owner's manual before using this equi -

ment.

2. Do not allow children to o erate the tow vehicle or the

tine cultivator.

3. Do not allow adults to o erate the tow vehicle or the

tine cultivator without ro er instruction.

4. Do not allow anyone to ride on the tow vehicle or the

tine cultivator.

5. Before lowering the tine cultivator, make sure no one

is near the area of o eration.

6. Lower the tine cultivator when leaving the tow

vehicle unattended.

7. Wear a ro riate footwear when using the tine culti-

vator. The ti of each tang on the cultivator is ointed

and shar !

8. Tow vehicle braking and stability may be affected by

the tine cultivator. Drive slowly with the tine cultivator

in the trans ort osition. Stay off steep slopes.

9. Sto and ins ect the equi ment for damage after

striking an object. Re air any damage before con-

tinuing o eration.

10. Kee all nuts and bolts tight and be sure that the

equi ment is in safe o erating condition.

11. Before attaching or removing the tine cultivator, ark

and lock the tow vehicle in a safe condition.

LOOK FOR THIS SYMBOL TO POINT OUT

IMPORTANT SAFETY PRECAUTIONS. IT

MEANS – ATTENTION! BECOME ALERT!

YOUR SAFETY IS INVOLVED.

CAUTION: VEHICLE BRAKING AND

STABILITY MAY BE AFFECTED BY THE

ADDITION OF AN ACCESSORY OR AN

ATTACHMENT. BE AWARE OF CHANG-

ING CONDITIONS ON SLOPES.

CARTON CONTENTS

1. Cross Brace

2. De th Gauge Bar (2)

3. Weight Bracket

4. Mast Extension Stra (2)

5. Mast Side (2)

6. Mast Lift Stra (2)

7. Su ort Bracket

8. Cultivator Assembly

Parts Package (see age 3)

For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

KEY QTY. DESCRIPTION KEY QTY. DESCRIPTION

A 2 Category 1 Pin

B 1 Pivot Pin

C 1 Haircotter Pin, 1/8"

D 2 Hex Bolt, 3/8" x 2-1/4" Lg.

E 2 Hex Bolt, 1/2" x 1-1/2" Lg.

F 2 Hex Bolt, 1/2" x 2-3/4" Lg.

G 1 Hex Bolt, 1/2" x 3-1/2" Lg.

H 2 Hex Bolt, 3/8" x 1" Lg.

I 8 Hex Nut, Nylock, 3/8"

J 2 U-Bolt, 3/8"

K 5 Hex Nut, Nylock, 1/2"

L 1 S acer

M 2 Lock Washer, 7/8"

N 2 Hex Nut, 7/8"

PARTS PACKAGE CONTENTS – PARTS SHOWN ACTUAL SIZE

For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

ASSEMBLY

TOOLS REQUIRED FOR ASSEMBLY

(2) 3/4" Wrenches

(2) 9/16" Wrenches

(2) 1-1/8" Wrenches or Adjustable Wrenches

(1) 1-5/16" Wrench or 12" Adjustable Wrench

Remove all loose arts and the hardware ackage

from the shi ing carton. Lay out and identify each

art and the hardware as shown on ages 2 and 3. Be

sure the carton is em ty before it is discarded.

1. Attach two de th gauge bars to the frame using a

3/8" U-bolt and two 3/8" Nylock hex nuts for each

bar. Put each de th gauge bar next to each out-

side tang on the rear of the frame as shown in

figure 1. Use the holes in each bar that will give the

desired working de th, if known at this time. Use

matching holes in both de th gauge bars to kee

the cultivator level.

NOTE: For effective de th control a de th gauge bar

must not be located directly behind a front tang.

2. Attach two mast extension stra s to the front of

the frame using two 1/2" x 2-3/4" hex bolts and two

1/2" Nylock hex nuts. Point the bent end of each

stra toward the outside of the frame. Do not

tighten yet. See figure 2.

CAUTION: THE CULTIVATOR TANGS

HAVE SHARP POINTS. USE CARE

WHEN HANDLING AND ASSEMBLING

THE TANGS. WEAR GLOVES FOR

EXTRA PROTECTION AGAINST CUTS.

FIGURE 2

1/2" NYLOCK

HEX NUT

MAST EXTENSION

STRAP (RIGHT

SIDE)

1/2" x 2-3/4"

HEX BOLT

FRONT

FIGURE 1

3/8" NYLOCK

HEX NUT

3/8"

U-BOLT

DEPTH

GAUGE BAR

DEPTH

GAUGE

BAR

3. Attach the cross brace and the two mast sides to

the ends of the mast extension stra s. The cross

brace is between the extension stra s while the

mast sides are on the outside. The cross brace

and mast sides are connected to the extension

stra s using two category 1 ins, two 7/8" lock

washers, and two 7/8" hex nuts. Do not tighten

yet. See figure 3.

WORKING

DEPTH

FIGURE 3

MAST

SIDE

CATEGORY

1 PIN

CROSS

BRACE

7/8" LOCK WASHER

7/8" HEX

NUT

EXTENSION

STRAP

For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

4. Arrange the mast lift stra s as shown in figure 4.

Place the stra s and the s acer between the mast

sides, fastening them to the lower hole in the mast

sides using a 1/2" x 3-1/2" hex bolt and 1/2" Nylock

hex nut. Do not tighten yet.

FIGURE 4

MAST LIFT

STRAP

SPACER

1/2" NYLOCK

HEX NUT

1/2" x 3-1/2"

HEX BOLT

FIGURE 6

1/2" x 1-1/2"

HEX BOLT

1/2" NYLOCK

HEX NUT

SUPPORT

BRACKET

MAST LIFT

STRAP

FIGURE 5

PIVOT PIN

1/8" HAIR

COTTER PIN

5. Install the ivot in through the u er hole at the

end of the mast sides. Secure the ivot in with a

1/8" hair cotter in. See figure 5.

6. Attach the lower end of each mast lift stra to the

outside of the welded frame braces and attach the

su ort bracket to the inside of the frame braces.

Use two 1/2" x 1-1/2" hex bolts and two 1/2"

Nylock hex nuts. Do not tighten yet. See figure 6.

7. Attach the front of the weight bracket to the su -

ort bracket using two 3/8" x 1" hex bolts and two

3/8" Nylock hex nuts. Attach the sides of the

weight bracket to the rear of the frame using two

3/8" x 2-1/4" hex bolts and two 3/8" Nylock hex

nuts. See figure 7.

8. Tighten all loose bolts and nuts at this time.

FRAME

BRACES

MAST

SIDE

FIGURE 7

3/8" x 1"

HEX BOLT

3/8" x 2-1/4"

HEX BOLT

WEIGHT

BRACKET

3/8" NYLOCK

HEX NUT 3/8" NYLOCK

HEX NUT

For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

FIGURE 8

ADJUST DEPTH

GAUGE BARS UP

OR DOWN AS

REQUIRED TO

CHANGE DEPTH

OF CULTIVATION

CAUTION: USE CARE WHEN WORKING

AROUND A RAISED CULTIVATOR. KEEP

YOUR FEET AND HANDS FROM UNDER

THE TANGS AT ALL TIMES. SERIOUS

INJURY CAN RESULT SHOULD THE

CULTIVATOR DROP UNEXPECTEDLY.

OPERATION

The tine cultivator is used to loosen soil and other

ty es of landsca e material.

1. Before starting, make sure the material to be

cultivated, such as dirt, is dry enough by squeez-

ing some in your hand. If it forms a ball that doesn't

crumble, the material may be too wet to cultivate.

2. The cultivator can be set for various de ths of

cultivation. To change the cultivation de th, raise

or lower the two de th gauge bars located on the

back of the frame assembly as shown in figure 8.

To adjust the de th gauge bars, remove the nuts

from the U-bolt securing each bar to the frame.

Then re osition the U-bolt in another set of holes

for the desired de th of cultivation. The bars can

be adjusted u or down in 1" increments. Be sure

to use the same matching airs of holes in each

de th gauge bar to ensure the cultivator is level.

3. U to 160 lbs. of weight may be added to hel

increase enetration. 40 lb. suitcase weights can

be attached to the center weight bracket, or con-

crete blocks or other weights may be tied or

stra ed to the cultivator frame. Before adding

weight, the cultivator should be attached to the

tow vehicle and lowered to the ground.

MAINTENANCE

1. Check for and tighten any loose hardware before

each use.

2. Clean the cultivator and lightly oil only bare metal

after each use.

3. Remove all dirt and rust. Touch u aint before

lacing cultivator in storage.

4. Store cultivator inside a dry area.

For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

18 7

the fastest way to purchase arts

www.speedepart.com

REPAIR PARTS FOR MODEL NO. 45-0355-131

3 PT. HITCH TANG CULTIVATOR

REF. PART QTY. DESCRIPTION

NO. NO. REF. PART QTY. DESCRIPTION

NO. NO.

1 48982 2 Lock Washer, 7/8"

2 48970 2 Hex Nut, 7/8"

3 25154 1 Cross Brace

4 25167 1 S acer, Mast Lift Stra

5 25180 2 Mast Lift Stra

6 43343 1 Haircotter Pin, 1/8" x 2-3/8"

7 712-3083 5 Hex Nut, Nylock, 1/2"

8 25158 2 Mast Side

9 48979 2 Category 1 Pin

10 25169 2 Mast Extension Stra

11 46526 1 Hex Bolt, 1/2" x 3-1/2" Lg.

12 48978 1 Pivot Pin, 3-3/4" Lg.

13 HA180132 2 Hex Bolt, 3/8" x 2-1/4" Lg.

14 43001 2 Hex Bolt, 3/8" x 1" Lg.

15 25191 1 Weight Bracket

16 25192 1 Su ort Bracket

17 43020 2 Hex Bolt, 1/2" x 1-1/2" Lg.

18 HA21362 26 Hex Nut, Nylock, 3/8"

19 43510 2 Hex Bolt, 1/2" x 2-3/4" Lg.

20 64772 1 Cultivator Frame Assembly

21 25170 9 Tang Su ort Stra

22 43022 9 Cultivator Tang

23 46853 11 U-Bolt, 3/8"

24 24238 2 De th Gauge Bar

49358 1 Owners Manual

For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

REPAIR PARTS

Agri-Fab, Inc.

303 West Raymond

Sullivan, IL. 61951

217-728-8388

www.agri-fab.com

the fastest way to purchase arts

www.speedepart.com

For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

Tabla de contenidos

Otros manuales de Caña del timón de Agri-Fab

Agri-Fab

Agri-Fab 45-04381 Manual de usuario

Agri-Fab

Agri-Fab 45-02941 Manual de usuario

Agri-Fab

Agri-Fab 45-03083 Manual de usuario

Agri-Fab

Agri-Fab 45-03081 Manual de usuario

Agri-Fab

Agri-Fab 45-03085 Manual de usuario

Agri-Fab

Agri-Fab 45-0298 Manual de usuario

Agri-Fab

Agri-Fab 45-0308 Manual de usuario

Agri-Fab

Agri-Fab 45-0457 Manual de uso y cuidado

Agri-Fab

Agri-Fab 45-0381 Manual de usuario

Agri-Fab

Agri-Fab 45-0355 Manual de usuario

Agri-Fab

Agri-Fab 45-03084 Manual de usuario

Agri-Fab

Agri-Fab 45-0383 Manual de uso y cuidado

Agri-Fab

Agri-Fab 45-0346 Manual de usuario

Agri-Fab

Agri-Fab 45-02661 Manual de usuario

Agri-Fab

Agri-Fab 45-0356 Manual de usuario

Agri-Fab

Agri-Fab 45-03082 Manual de usuario

Agri-Fab

Agri-Fab 45-0343 Manual de uso y cuidado

Agri-Fab

Agri-Fab 45-0365 Manual de usuario

Agri-Fab

Agri-Fab 45-0355-131 Manual de usuario

Agri-Fab

Agri-Fab 45-0264 Manual de usuario

Agri-Fab

Agri-Fab 45-0406 Manual de uso y cuidado

Agri-Fab

Agri-Fab Spike Aerator 45-0369 Manual de uso y cuidado

Agri-Fab

Agri-Fab 45-0294 Manual de uso y cuidado

Agri-Fab

Agri-Fab 45-0458 Manual de uso y cuidado

Manuales populares de Caña del timón de otras marcas

MTD

MTD 410R Manual de usuario

Craftsman

Craftsman 247.29931 Manual de usuario

MTD

MTD FRT Series Manual de usuario

Craftsman

Craftsman 917.298353 Manual de usuario

Troy-Bilt

Troy-Bilt Colt FT Manual de usuario

Ryobi

Ryobi 510r Manual de usuario

MTD

MTD OHV Series Manual de usuario

YAT

YAT YT5601-01 Manual de mantenimiento

Craftsman

Craftsman 917.296010 Manual de usuario

Troy-Bilt

Troy-Bilt OEM-290-260 Manual de usuario

Scheppach

Scheppach MTP560 Instrucciones de montaje

GARDEN WAY

GARDEN WAY 12194 Manual de usuario

Classen

Classen STAND-AER SA-25 Instrucciones de instalación y mantenimiento

Craftsman

Craftsman 850 Series Manual de usuario

DR PILOT 2 Guía de inicio rápido

Altrad

Altrad ATIKA BH 1400 N Guía

WIL-RICH

WIL-RICH 2500 Manual de usuario

Viking

Viking HB 685 Manual de usuario